HASHIMA HP-450CS Manuale utente
HASHIMA
HASHIMA COMPACT PRESS
HP-450C/CS
INSTRUCTION MANUAL
HASHIMA CO.,LTD
SPECIFICATIONS
MODEL HP-450C/CS
POWER SUPPLY 1P-220V
RATED OUTPUT HEATER ４．５KW
MOTOR ４０W
TEMPERATURE A(MAX) ２００℃
PRESSURE (MAX) １．５KG/cm
BELT SPEED ８．７ｍ／min.
HEATING TIME ５ − ２０ sec.
FUSING WIDTH ４５０ｍｍ
DEMENTIONS W １６６０ｍｍ
D ８８０ｍｍ
H ４９０ｍｍ
WEIGHT １５２ｋｇ
Attention to be paid at the time of installation
1. Install this machine, which weights 152kg, in regard to the 450C/CS
respectively, on the robust foundation horizontally.
2. Don’t install this machine near the object easy to burn, as it generates high
temperature when it has been put into use. Exclude, in addition, dusts and
others stuck onto this machine periodically.
3. Connect the machine to an exclusive power source corresponding with the
ratio consumption power by referring to the specifications.
4. Don’t fail to the ground .By the way ,it has no relations to the rotary direction
of the belt.
5. In the case where you change the power source plug or lengthen construction
shop near by.
6. When the machine has been brought in or when it has been transferred, don’t
fail to remove the main unit’s cover, before ensuring that the upper and lower
belt warping prevention limit switches place correctly the belt between them
from both sides. (Refer to next page.)
Attention to be paid at the time of using
1. Don’t fail to read the User’s Manual prior to the usage.
2. Don’t fail to remove the main unit’s cover and ensure that the upper and lower
warp prevention limit switches place correctly the belt between them from
both sides, before connecting the power source. (Refer to next page.)
3. Wipe off dusts using a dry floor mat, before inserting the material.
4. Pay sufficient attention not to make contact with the belt and the upper cover
whose temperature rises high nor mount things on them.
5. Don’t absolutely put your hands on to the roller inside the machine beyond the
necessity at the time you insert the material for fear that they might be
caught in.
6. Don’t put any things to the main unit of the press except the materials to be
inserted.
7. Disconnect the power source breaker immediately and insert the manual
handle (an accessory) to the emergency screw, then, turn it to the arrow
marked direction in order to remove the unusual things before the operation,
if they have been inserted.
8. When the material, has twined rounded the strip off device at the exit of the
material, don’t fail to disconnect the power source breaker, before removing it.
9. Don’t fail to pull the power source plug off when you inspect the inside.
10. This machine is an exclusive use for fusing and folding the clothes. Don’t put it
to use for other purposes, otherwise resulting in troubles.
11. After the operation ensure that the machine has stopped completely, before
disconnecting the power source breaker without fail.
Procedure of usage
1. Set the power source to ‘ON’.(Ensure the ‘off ’condition of the timer switch.)
2. Press the start button. The lamp will light up and the machine will start
moving.
3. Set pressure to the designated by using the pressure adjust knob.
4. Set the fusing time by using the speed controller .Use it within the limit
between 5 and 20 seconds for the warp prevention.
5. Set the setting temperature by using the thermostat .It takes about 15
minutes before you’ll get the usable thermo-lamp will start blinking.
6. Here, you are able to start the operation.
At the time the operation is over.
1. Set the pressure to 0(zero).
2. Set the timer switch to ‘ON’. The machine stop automatically and the
surface temperature of the belt is below 100 degrees.
3. When the machine has stopped , set the power source breaker to ‘OFF’.
The holding’s adjustment
In the case where you want to strengthen the holding at the injecting entrance
of the machine when you’ve put the inside belt scale, pocket folding and others to
use, turn the holding’s handle to the right. Set the holding’s adjustment to
0(zero),when you try to fuse the interlining.
How to prevent and adjust roller moiré (puckering)
In the case where roller moiré has taken place on the fused material, fuse it by
lowering heat and pressure as low as possible. Even when the prevention is
impossible in spite of the efforts, adjustments to be shown below will be
necessary.
1. Remove the main unit’s cover.
2. Remove the rear cover.
3. You’ll find a screw for securing the moiré adjust roller on the side of the
machine . And you will find an other when you open the rear cover of the
machine loosen both of the stop screws and rise right and left equally.
4. The moiré is hard to appear when you bring up the roller.
5. Tighten both of the stop screws.
How to move the machine by hand at the emergency
Press the stop switch in order to stop the machine before setting the pressure to 0
(zero), when you’ve put other things to the belt’s injecting entrance by mistake.
Put the T-typed wrench (an accessory) on to the screw for emergency on the side of
the main unit and turn it to the arrow marked direction, before you will unload
the finished material. In the case where a hard thing has been put in the machine,
ensure the safety before resuming the operation for fear that the teflon belt and
rubber parts of the pressure roller might be damaged. And in the case of an
electric failure, put the T-typed wrench (an accessory ) on to the screw for
emergency use on the side of the main unit and turn it to the arrow marked
direction. before you’ll unload the finished material
Daily maintenance <<Pay attention to fear such accidents as burn and caught
–in.>>
Cleaning belts
Clean the belt while it is hot. Use the Hashima New Ace or the New Clean Spray
to clean the belt. In the case where you put the latter to use . pay attention not to
spray such electric parts as the warp prevention limit switch and others, resulting
in troubles. Moreover, don’t use the powders New Cleaning except when dirt is
remarkable. Wipe with sure the powders which have a character to be hardened
when it is cool. Apply the Hashima New Ace onto the belt for the prevention of
dirts.
Cleaning the cleaner
The cleaner is provided at the rear part of the machine. At the start of the
cleaning, don’t fail to pay attention so that the clean surface could make contact
with to belt. And observe it about twice a day to change the dirty surface if
necessary. The cleaner is to be removed when you push it to the manipulation
panel’s side. When you wind a new cloth. make it coincide with the rotary
direction of the belt and, then ,wind it ,not being caught in.
Cleaning the brush scraper.(C)
The brush, too, is provided at the rear part of the main unit of the machine. Raise the scraper
three or four times a day in order to clean.
Cleaning the rotary strip off blade (CS)
Pick the blade, using a piece of the cloth and move it left to right and right to left
in order to take the fusing resin resin and others away. Here. if the blade remains
lying ,raise it before cleaning it.
ATTENTION TO BE PAID MAINTANANCE OF FUSING MACHINE
Put-off electric sources, fill “grease” inside rollers every two weeks
You should use HASHIMA genuine grease and never use grease which contains
MOLYBDENUM (LACK OF THIS GIVES DAMAGES TO BEARINGS)
1. TAKE OUT MAIN COVER A.
2. FULL GREASE INTO THE PLACE OF ARROW MARKS.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali HASHIMA Accessori per macchine da cucire
