HCFA HCA2 Series Manuale utente

HCFA Corporation Limited

HARDWARE MANUAL

HCA2 SERIES PROGRAMMABLE CONTROLLERS

Foreword.......................................................................................................................................... 2

1. Introduction.................................................................................................................................5

1.1 Model Name....................................................................................................................... 6

1.2 Rules of Expansion........................................................................................................... 6

1.3 Back up Data...................................................................................................................... 7

1.3.1 EEPROM backup................................................................................................... 7

1.3.2 Capacitor backup................................................................................................... 7

1.3.3 Initialize Latched (Keep) Devices................................................................................ 7

2. Terminal layouts.........................................................................................................................8

3. Installation Notes.......................................................................................................................9

3.1 Product Outline.................................................................................................................. 9

3.2 HCA2RUN/STOP Control...............................................................................................10

3.3 General Specifications.................................................................................................... 11

3.4 PLC Mounting Arrangements........................................................................................ 12

3.5 DIN Rail Mounting........................................................................................................... 13

3.6 Direct Mounting................................................................................................................ 14

3.7 Wiring.................................................................................................................................14

3.7.1 Termination at Screw Terminals.........................................................................14

3.7.2 Removal and installation of quick-release terminal block............................. 15

3.8 Installing Optional Units..................................................................................................16

3.8.1 Expansion Boards................................................................................................ 16

4. Power Supply........................................................................................................................... 17

4.1 Wiring Techniques........................................................................................................... 17

4.2 Wiring Cautions................................................................................................................17

4.3 Power Supply................................................................................................................... 17

4.4 Power Requirements...................................................................................................... 18

4.5 Example Wiring................................................................................................................ 19

4.5.1 AC Power supply.................................................................................................. 19

4.5.2 24V DC Power supply......................................................................................... 19

4.5.3 12V DC Power Supply.........................................................................................20

4.6 Service Power supply..................................................................................................... 21

4.7 Earthing / Grounding....................................................................................................... 21

5. Inputs.......................................................................................................................................... 21

5.1 24V DC input Specifications.......................................................................................... 21

5.1.1 Typical Wiring........................................................................................................22

5.1.2 Input Circuit Connection......................................................................................22

HCFA Corporation Limited

5.1.3 Diodes and Inputs Connected in Series...........................................................22

5.1.4 Resistors and Inputs Connected in Parallel.................................................... 23

5.2 AC110V Input Extension Block......................................................................................23

6. Outputs.......................................................................................................................................24

6.1 Output Specifications...................................................................................................... 24

6.2 Relay Output Example....................................................................................................24

6.2.1 Product life of relay contacts.............................................................................. 24

6.2.2 Output circuit configuration.................................................................................25

6.3 Transistor Output Example............................................................................................ 27

6.3.1 Transistor Output Writing Diagram (Source Type)......................................... 27

6.3.2 Japanese Model Transistor Output (Sink Type)..............................................27

6.3.3 Response Times...................................................................................................28

6.3.4 External wiring precaution.................................................................................. 28

7. Diagnostics............................................................................................................................... 29

7.1 Preliminary Checks......................................................................................................... 29

7.2 ERROR LED ON (CPU ERROR)................................................................................. 29

7.3 Common Errors................................................................................................................29

7.4 Maintenance..................................................................................................................... 30

7.5 Operation and Error Flags............................................................................................. 30

7.6 PLC Status Registers...................................................................................................30

7.7 Error Registers................................................................................................................. 31

7.8 Error Codes...................................................................................................................... 31

7.9 Instruction List.................................................................................................................. 32

7.10 Device List...................................................................................................................... 33

HCFA Corporation Limited

Foreword

•This manual contains text, diagrams and explanations which will guide the reader in the

correct installation and operation of the HCA2 Series Programmable Controllers. It should

be read and understood before attempting to install or use the unit.

•If in doubt at any stage of the installation of an HCA2Series Programmable Controller

always consult a professional electrical engineer who is qualified and trained to the local

and national standards which apply to the installation site.

•If in doubt about the operation or use of HCA2Series Programmable Controller please

consult the nearest HCFA Electric distributor.

•This manual is subject to change without notice.

HCA2 SERIES PROGRAMMING CAUTION

Thank you for buying The HCFA HCA2 series controller.

Please note the following.

Notes: Block Move instruction

Applicable PLC: HCA2 Ver 1.00-2.10

Applicable instructions: BMOV, BMOVP(FNC15)

If the file register parameter setting and the registers D8000-D8225 are used as the

destination devices for the BMOV (BMOVP) instruction, program steps or file register data

may be lost or damaged. All other data registers can be used safely for BMOV(BMOVP)

instruction destination registers.

Program example

Guidelines for the safety of the user and protection of the HCA2.

This manual provides information for the installation and use of the HCA2. The manual

has been written to be used by trained and competent personnel. The definition of such a

person or persons is as follows;

a) Any engineer who is responsible for the planning, design and construction of automatic

equipment using the product associated with this manual should be of a competent nature,

(trained and qualified to the local and national standards required to fulfill that role). These

engineers should be fully aware of all aspects of safety with regards to automated

equipment.

b) Any commissioning or service engineer must be of a competent nature, trained and

qualified to the local and national standards required to fulfill that job. These engineers

should also be trained in the use and maintenance of the completed product. This

includes being completely familiar with all associated documentation for the said product.

All maintenance should be carried out in accordance with established safety practices.

c) All operators of the completed equipment (see Note) should be trained to use that

HCFA Corporation Limited

product in a safe manner in compliance to established safety practices. The operators

should also be familiar with documentation which is associated with the operation of the

completed equipment.

Note :The term ‘completed equipment’ refers to a third party constructed device which

contains or uses the product associated with this manual.

Note’s on the symbols used in this manual

At various times throughout this manual certain symbols will be used to highlight points of

information which are intended to ensure the users’ personal safety and protect the

integrity of the equipment. Whenever any of the following symbols are encountered, its

associated note must be read and understood. Each of the symbols used will now be

listed with a brief description of its meaning.

Hardware warnings

1) Indicates that the identified danger WILL cause physical and property damage.

2) Indicates that the identified danger could POSSIBLY cause physical and property

damage.

3) Indicates a point of further interest or further explanation.

Software warning

1) Indicates special care must be taken when using this element of software.

2) Indicates a special point which the user of the associate software element

should be aware of.

3) Indicates a point of interest or further explanation.

•Under no circumstances will HCFA Electric be liable or responsible for any

consequential damage that may arise as a result of the installation or use of this

equipment.

•All examples and diagrams shown in this manual are intended only as an aid to

understanding the text, not to guarantee operation. HCFA Electric will accept no

responsibility for actual use of the product based on these illustrative examples.

•Please contact a HCFA Electric distributor for more information concerning applications

in life critical situations or high reliability.

Note Concerning the CE Marking

This document does not guarantee that a mechanical system including this product will

comply with the following standards. Compliance to EMC directive and LVD directive of

the entire mechanical system should be checked by the user / manufacturer.

HCFA Corporation Limited

For more details please contact the local HCFA Electric sales site.

Programmable logic controllers are open-type devices that must be installed and used

within conductive control boxes.

Please use the HCA2Series programmable logic controllers while installed in conductive

shielded control boxes.

Please secure the control box lid to the control box (for conduction).

Installation within a control box greatly affects the safety of the system and aids in

shielding noise from the programmable logic controller.

HCFA Corporation Limited

1. Introduction

This manual covers hardware installation instructions for the HCA2Series PLC.

Table 1.1: HCA2Main Modules

AC Power Supply DC Power Supply DC INPUT Relay output Transistor output

Points L(mm) W(mm) H(mm)

HCA2-8X6Y(14 points) 100.2 90 81

HCA2-14X10Y(24 points) 130.2 90 81

HCA2-24X16Y(40 points) 182.2 90 83

HCA2-36X24Y(60 points) 220.2 90 83

Figure 1.1 :Main unit outline

Table 1.2: Powered Extension Units

■Input

Expansion

■Output

Expansion

■Special Expansion

Block/Analog Unit

■Input &

output

Expansion

Block

■Positioning

Control Block

■Analogue

Block

TX2N-8EX

TX2N-16E

TX2N-8EYR

TX2N-8EYT

TX2N-16EY

A/D

TX2N-2A

TX2N-4A

TX2N-8A

D/A

TX2N-2D

TX2N-4D

TX2N-8ER

TX2N-16E

TX2N-32E

TX2N-48E

TX2N-1PG

TX2N-4PG

TX2N-10PG

TX2N-1RM-SE

TX2N-10GM

TX2N-20GM

TX0N-3A

TX2N-4AD-4D

TX2N-4AD-2D

TX2N-4AD-TC

TX2N-4AD-PT

TX2N-2LC

TX2N-1HC

HCFA Corporation Limited

1.1 Model Name

Code Contents

1HC represents the Chinese Character Pinyin Initials ‘HeChuan’

2A2 represents series number of PLC. HC PLC Types: A1~A8

336X represents 36 input points; Input points of A2 series: 8X, 14X, 24X, 36X

424Y represents 24 output points; Output points of A2 series: 6Y、10Y、16Y、24Y

Corresponding to the combination of input & output:

A2: 14 points, 24 points, 40 points, 60 points

5R(T) represents output type of PLC R: relay output T: transistor output

6A(D) represents power supply type of PLC A: AC 85V~264V input D: DC

20.4V~26.4V input

Table : Configuration Notes

A HCA2 Series Main Unit

B HCA2 Expansion Boards for Analog

I/O

C HCA2 Expansion Boards without

Analog I/O

D Memory Cassette or Display Module

E Programming Software

F RS-232C/RS-422 Converter for PC

F’ USB/RS-422 Converter for PC

G Dedicated Programming Tools

1.2 Rules of Expansion

The maximum I/O for an HCA2system is 128 I/O points and 8 special function blocks.

The HCA2 Series can be expanded as follows when used independently.

- 2 special function blocks

- 1 special function block and up to 16 I/O points

- Up to 32 I/O points

An AC powered HCA2 can be expanded by 8 special function blocks when used in

conjunction with an HCA5 extension unit (2+6).

•If a DC powered main unit is used with a power supply of less than 24VDC -15% (20.4V

DC or less), then it cannot be fully expanded by using special function blocks or powered

extension units.

It can accommodate a maximum of an additional 32 I/O points.

HCFA Corporation Limited

•If an HCA2 expansion board is being used, it does not alter the rules of expansion

outlined above, as it utilizes special M coils for its operation and therefore does not

contribute to the maximum 128 I/O point count. Only one special function board can be

used at any time.

See section 3.8 for more details.

1.3 Back up Data

1.3.1 EEPROM backup

Data includes the Program, Comment, File Registers (D1000 ~ D7999), and parameter

data.

This will be stored as long as the EEPROM is not damaged. HCFA Electric has

guaranteed a life cycle time of 10,000 writes to the EEPROM memory. Users may

experience operational writes to the EEPROM in excess of 10,000; however, due to

temperature effects a quantitative estimation cannot be given.

When saving the device status in the EEPROM, the electric power of the PLC's built-in

capacitor is used.

If the PLC has been powered on for five minutes or more, the following device data will be

saved in the EEPROM at power down: S0 ~ S127, M384 ~ M511, C16 ~ C31, C235

~C255, and D128 ~ D255.

When the EEPROM keep device status cannot be correctly saved to the EEPROM by

shortage of electric charge, at the next power-on the status of the device will be that which

saved to the EEPROM at the last save.

1.3.2 Capacitor backup

The capacitor backed memory includes M512 ~ M1535, S128 ~ S999, T246 ~ T255, C32

~ C199, C220 ~ C234, D256 ~ D7999 and the RTC.

The capacitor backed memory will retain data for a maximum of 10 days (Ambient

temperature: 25 °C), and requires 30 minutes to recharge upon power up.

Note: The HCA2 does not have battery backup, if a system requires backup of more than

10 days (Ambient temperature: 25 °C), a peripheral backup power source must be

provided.

1.3.3 Initialize Latched (Keep) Devices

•When using non-latched devices

To use the latched devices as the non-latched devices, reset the latched devices by an

initial pulse (M8002) in program.

•When using capacitor latched (keep) devices

If the voltage of a capacitor drops, the capacitor keep device status may be stored

incorrectly. Therefore, when using the PLC after it has been powered off for more than 10

HCFA Corporation Limited

days (Ambient temperature: 25 °C), re-set up the required devices and the current time

after initializing capacitor latched (keep) devices before selecting RUN.

Initialization method

Latched (keep) devices can be initialized in the PLC memory by using peripheral

equipment, and the special auxiliary relay M8032, or executing the ZRST instruction. The

two major methods are described below.

•Latch memory all clear by special auxiliary relay (M8032)

When M8032 is turned ON, all latched (keep) devices (including reset coils of timers and

counters) are cleared. M8032 can be turned ON and OFF using the forced ON/OFF

operation from peripheral equipment or within the sequence program. Note that latched

devices cannot be turned ON while M8032 is ON. When turning ON M8032 within the

sequence program, note that latched devices are cleared during END processing after

M8032 is turned ON.

Program example: This program clears all latched devices.

•Reset of device by ZRST (zone reset) instruction

The ZRST instruction can clear multiple devices at once. (Because a limited device range

can be specified for the ZRST instruction, only part of the latched (keep) devices can be

cleared at a time.)

However, initialization method by the ZRST

instruction for capacitor backed timer and

counter devices

(T246 ~ T255, C32 ~ C199, C220 ~ C234)

does not reset the associated coil devices.

In order to initialize the associated coil

devices, execute the RST instruction for

the coil devices being used in the user

program as shown in the example program

on the left.

2. Terminal layouts

The following selection of terminal layouts are taken from the HCA2product range.

Note: All layouts are schematic only and are intended to aid the creation of wiring

diagrams.

HCFA Corporation Limited

3. Installation Notes

The installation of HCA2products has been designed to be safe and easy. When the

products associated with this manual are used as a system or individually, they must be

installed in a suitable enclosure. The enclosure should be selected and installed in

accordance to the local and national standards.

3.1 Product Outline

Figure 3.1:Features of the HCA2 PLC

Indice

Altri manuali HCFA Controllori

HCFA

HCFA Q Series Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente