Heath Consultants RMLD-CS Manuale utente

POWERING INSTRUMENT

Power ON: Press and hold the middle button for 3 seconds.

RMLD-CS Quick Start Guide

SELF-TEST

Self-Test feature should be performed daily before survey to ensure that the

instrument is operational.

Self-Test and Calibration procedure:

1. Turn on the instrument and allow instrument to successfully boot up.

2. Press the MENU button and select the SELF-TEST option.

3. The screen will display and guide the next steps for the operator to

follow within 10 seconds (enough time for the steps).

4. Place the instrument in its designated area in the carrying case, making

 sureitisallthewayinplaceandat.

5. Statuses of test will be present on the display and by audible tones. A

continuous one beep every second means the instrument passed the

self-test.

a. If the instrument fails, two beeps every second will play and operator

should repeat self-test.

b. If instrument fails on a third attempt, contact Heath Consultants.

SPOTTER LASER

The green spotter laser in under the control of the operator and is on for one

minute when the spotter “ON” button has been pressed.

Tousethespotterlaser,theusermustrstENABLEthelaserintheMENU.To

dothis,selectMENU,scrolldowntoSPOTTERCONTROL,thenselectENABLE.

www.heathus.com

713.844.1300

Power OFF: Press and hold the middle button for 3 seconds.

The spotter icon will now be visible in the top menu bar. When the spotter laser

is turned ON, the icon will change from white to green.

The left menu button will now display the spotter ON

option. Pressing the left button (on/off) will activate the

spotter for 1 minute.

DMD MODE

The Digital Methane Detection (DMD) mode greatly enhances the use of the

RMLD-CS. In most situations, the operator should survey with the DMD mode

turned on. To turn on the DMD mode, press the MENU button, select AUDIO

MODE, then select DMD.

DATA LOGGING

The RMLD-CS data logging feature allows the instrument to store complete

telemetry records of the instrument, while powered on, to an internal SD mem-

ory card. To enable this feature, select DATA LOGGING from the MENU, then

selectENABLED.

To disable this feature, select DATA LOGGING in the MENU, then select DIS-

ABLED.

NOTE: Data logging does not need to be enabled in order for the instrument

to record FAULT logs, SELF-TEST logs, or screen captures.

USB FILE TRANSFER

Toaccessrecorded/captureddata,plugintheprovidedUSBcordintothe

instrumentwhilepoweredonandtotheoperator’sPC.TheUSBmodein

theMENUmustbesetto“MassStorageDevice”forPCrecognitionandle

logging operations.

NOTE:RecognitionofRMLD-CSmaytakesometimeonrstpluginasthe

required drivers are installed. Please allow time for this initial process to

complete.

Aleexplorerwindowwillopenautomaticallywhenthedeviceisreadyfor

access.Thebasicleandfolderstructureisshownbelow.

Daily Folders: Will be created in the YYMMDD format

Self Test Logs: Will be created in the format, hhmmss-SELF_TEST.txt

Data Logs: Will be created in the format, YYMMDD-hhmmss_’USER’_Datalog.txt

NOTE:‘USER’willbereplacedbytheoperatorprolebeingusedduring

operation.

SERVICE AND SUPPORT

Houston Factory Service Center

Manufacturing Division

9030 Monroe Rd

Houston, TX 77061

Phone: 713.844.1300

www.heathus.com

Datatelemetryisrecordedintomultipleloglesduringoperation.Thefollow-

ingmeasurementinformationiscontainedwithinthelogles:

• CH4 PPM-M measurement

• Batterylevel

• Batteryvoltage

• GPS location

• Timestamp

• Serial number of instrument

Theloglealsocontainsvarioussystemstatuseldsandvaluesthatcanbe

used to help evaluate unit performance or aid in troubleshooting if a fault

condition occurs.

The alarm level setting is

shown on the display within

a rectangle (AL 20).

ALARM LEVELS

To change the Alarm Detection Threshold, press the MENU button, scroll down

and select ALARM LEVELS. Press the down button to increase or decrease

the threshold and SELECT to move the placeholder. The higher the threshold

setting is, the less sensitive the instrument becomes. Press the back arrow

button to return to the menu.

NOTE:

Read and understand manual fully

before use.

Manual available online:

www.heathus.com/products/rmld-cs

Altri manuali per RMLD-CS

Altri manuali Heath Consultants Sensore di sicurezza

Heath Consultants

Heath Consultants RMLD-CS Manuale utente

Manuali Sensore di sicurezza popolari di altre marche

THORLABS

THORLABS PDA10JT Manuale utente

Waeco

Waeco UV-DETECT Manuale utente

Intermatic

Intermatic IOS-DSIMF Manuale utente

urmet domus

urmet domus 1083 Manuale utente

Siemens

Siemens AZL66 Series Manuale utente

BTI

BTI Profiline Multi Finder Manuale utente

Challenger

Challenger SL01 Manuale utente

DMP Electronics

DMP Electronics 1122INT Manuale utente

Rielta

Rielta Ladoga MK-RK Manuale utente

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuale utente

Bosch

Bosch DS835 Manuale utente

DBI SALA

DBI SALA EZ Stop Manuale dell'operatore

Lamptime

Lamptime ST05C Manuale utente

Ubiquiti

Ubiquiti MFI-MSC Manuale utente

Subsite

Subsite 910R Istruzioni per l'installazione

Satel

Satel OPAL Pro Manuale utente

Aleph

Aleph XC-1XTEU Manuale utente

Pima

Pima LARIS QUAD Manuale utente