Heath Zenith 6168 Manuale utente

Wireless Door

Sensor Chime

Model 6168

1. Plug wireless chime into wall

outlet.

Note: The volume control is on the back

of the wireless chime. Unplug chime to

adjust volume.

To reduce the risk of electrical shock,

this equipment has a polarized plug

(one blade is wider than the other). This

plug will ﬁt in a polarized outlet only one

way. If the plug does not ﬁt fully in the

outlet, reverse the plug. If it still does

not ﬁt, contact a qualiﬁed electrician to

install the proper outlet. Do not attempt

to bypass this safety feature.

Chime

Volume

Control

Wireless Plug-in

Chime

Sensor

Magnet

Spacer

This package includes:

• Wireless plug-in chime

• Door sensor with battery

• Door magnet

• Magnet spacer

• Hardware pack

-2- 595-5724-04

Installation

Important considerations: The sensor must be mounted to the door jamb.The

magnet should be attached to the door. Sensor is for indoor use only.

2. Install alkaline type A23 12 volt push button

battery (included). Remove back of case by

pushing in tab on bottom with a small screw-

driver. See diagram inside sensor for correct

battery orientation.

3. Select mounting location. The maximum gap

between sensor and magnet is 1/2" (13 mm).

The arrows located on the face of each com-

ponent must be aligned and facing toward each

other. The magnet must be beside the sensor.

Note: If the magnet is recessed, use spacer to

ensure proper alignment.

4. Test range. Before mounting, hold sensor and

magnet in selected location and verify opera-

tion. While holding the sensor still, move the

magnet away from the sensor to simulate door

being opened.Verify red LED on sensor ﬂashes

momentarily and chime sounds.Note: If sensor

does not operate correctly, see Troubleshooting

Guide.

Alignment Arrows

WARNING: To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.

• If battery is swallowed, immediately notify doctor.

1/2" Maximum

Use Optional

Spacer if Needed

-3-595-5724-04

Use Optional

Spacer if Needed

5. Mount sensor.

Screw Mounting: Attach sensor back cover to

wall using two short screws (provided). Snap

sensor onto back cover.

Tape Mounting: Apply foam tape to the sensor

back cover. Stick sensor back cover to frame of

door in desired position.Snap sensor onto back

cover.

6. Mount magnet.Repeat step 5 to attach magnet

(and spacer if needed) to door using two screws

(provided). Note: If using spacer, use the two

long screws (provided).

-4- 595-5724-04

12345678

Inside

Sensor

Remove screw to

open access door

Back of Chime

Tune Setting

Tune Setting (Not

used on all models)

Note: Some models might require

the use of tweezers to remove and

replace the jumpers.

Tune Settings

Your Heath®/Zenith wireless chime has different selectable tunes: Ding (one

note), Ding-Dong (two note), or Westminster (eight note) (Available on se-

lected Heath®/Zenith chimes). The factory setting is for the Ding-Dong tune

(or Westminster, when available). This tune can be changed by following the

instructions below.

• Ding (one note tune)

Sensor: Add a jumper to location 8.

• Ding-Dong (two note tune)

Sensor: Remove jumper from location 8.

Chime: Remove jumper from location 8.

• Westminster (Eight note tune) (Available on selected Heath®/Zenith

chimes)

Sensor: Remove jumper from location 8.

Chime: Add a jumper to location 8.

Note: All models have both front and back door tune capabilities.You may pur-

chase any Heath®/Zenith wireless push button for a second entrance.

-5-595-5724-04

Troubleshooting

A. Chime does not sound:

• Red light on the sensor does not light. Check battery polarity. Replace the

sensor battery.

• Red light on the sensor does light. Make sure sensor and chime codes

are the same (see Code Setting below). Make sure the plug-in chime has

power going to it.

B. Chime sounds when not intended (false triggers): Chime is receiving

interference from another wireless device; change the code setting (see

Code Setting below).

C. Battery seems OK, but the chime does not work when installed:

• Do not mount the sensor on metal or near metal studs. This reduces the

sensor range. Use 1/4" to 1/2" (6 to 13 mm) wood shims to move the sen-

sor off the metal surface.

• Concrete ﬂoors may reduce range. Move chime away from ﬂoor.

• Try different locations for the chime closer to the sensor.

D. Code Setting:

It is recommended to only change one code position at a time and then check

to see if system is functioning properly.

1. Unplug chime from power source.

2. Open the cases and locate the jumpers on both the sensor and chime.

3. The sensor and chime both have eight different jumper locations. Jumper

positions 1 through 7 are used for setting the code.

Continued

-6- 595-5724-04

12345678

* Code Settings 1-7

Must Match Both

Sensor and Chime

Inside

Sensor

Remove

screw to open

access door

Back of Chime

4. To change the code, either:

• Add a jumper to the same location on both the sensor and the chime

or...

• Remove a jumper from the same location on both the sensor and the

chime or...

• Move a jumper on the sensor from one location to another.Move the corre-

sponding jumper on the chime to match the new location in the sensor.

Example: Move jumper at location “5” to location “4” on both the sensor

and the chime.

Note: Jumpers in positions 1 through 7 must be exactly the same for both

the sensor and chime for this system to function.

Note: Unit will come factory set with jumpers in locations 5, 6, and 7 on the

sensor and on the chime.

The range of the wireless chime can vary with location, temperature, and

battery condition.

Note: Some models might require the use of

tweezers to remove and replace the jumpers.

HeathCo LLC reserves the right to discontinue and to change speciﬁcations at any time

without notice without incurring any obligation to incorporate new features in previously

sold products.

-7-595-5724-04

Regulatory Information

This device complies with Part 15 of the FCC Rules and RSS-210 of Industry

Canada.Operation is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

The user is cautioned that changes or modiﬁcations not expressly approved by

the party responsible for regulatory compliance could void the user's authority

to operate the equipment.

Technical Service

Please call 1-800-858-8501 (English speaking only) for assistance

before returning product to store.

If you experience a problem, follow this guide. You may also want to visit our

Web site at: www.hzsupport.com. If the problem persists, call* for assistance

at 1-800-858-8501, 7:30 AM to 4:30 PM CST (M-F).You may also write* to:

HeathCo LLC

P.O. Box 90004, Bowling Green, KY 42102-9004

ATTN: Technical Service

* If contacting Technical Service, please have the following information available:

Model Number, Date of Purchase, and Place of Purchase.

No Service Parts Available for this Product

FIVE YEAR LIMITED WARRANTY

This is a “Limited Warranty” which gives you speciﬁc legal rights.You may also have

other rights which vary from state to state or province to province.

For a period of ﬁve years from the date of purchase, any malfunction caused by factory

defective parts or workmanship will be corrected at no charge to you.

Not Covered - Repair service, adjustment and calibration due to misuse, abuse or

negligence, light bulbs, batteries, and other expendable items are not covered by

this warranty. Unauthorized service or modiﬁcation of the product or of any furnished

component will void this warranty in its entirety. This warranty does not include

reimbursement for inconvenience, installation, setup time, loss of use, unauthorized

service, or return shipping charges.

This warranty covers only HeathCo LLC assembled products and is not extended to other

equipment and components that a customer uses in conjunction with our products.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,

EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION OR

CONDITION OF MERCHANT ABILITY ORTHATTHE PRODUCTS ARE FIT FOR ANY

PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL,

INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

REPAIR OR REPLACEMENT SHALL BETHE SOLE REMEDY OF THE CUSTOMER

AND THERE SHALL BE NO LIABILITY ON THE PART OF HEATHCO LLC FOR ANY

SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUD-

ING BUT NOT LIMITED TO ANY LOSS OF BUSINESS OR PROFITS, WHETHER

OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitation or exclu-

sion may not apply to you. Please keep your dated sales receipt, it is required for all

warranty requests.

-8- 595-5724-04

Control del

Volumen de la

Campana

1. Enchufe la campana inalám-

brica en el tomacorriente de la

pared.

Nota: El control del volumen está

en el reverso de la campana ina-

lámbrica. Para cambiar el volumen

desenchufe la campana.

Para reducir el riesgo de choque

eléctrico, este equipo tiene un en-

chufe polarizado (una patilla es más

ancha que la otra). Este enchufe

podrá insertarse en un tomaco-

rriente polarizado solamente de

una manera. Si el mismo no entra

completamente en el tomacorriente,

invierta el enchufe. Si aún no encaja

completamente, póngase en contac-

to con un electrista competente para

qua éste instale el tomacorriente

correcto. No trate de suprimir esta

característica de seguridad.

Campana

inalámbrica para el

detector de puerta

Modelo 6168

Campana inalámbri-

ca enchufable

Detector

Imán

Espaciador

del imán

Este paquete tiene:

•

Campana inalámbrica enchufable

• Detector de puerta con batería

• Imán para la puerta

• Espaciador del imán

• Paquete de accesorios

-9-595-5724-04

Instalación

Consideraciones importantes: El detector debe ser montado en el marco

de la puerta. El imán debe ser colocado en la puerta. El detector es sólo para

uso dentro de casa.

Instalar pila alcalina de botón tipo A23 de 12

voltios (Se incluye). Extraer la parte posterior de

la caja presionando la aleta en el botón con un

destornillador pequeño.

Vea el diagrama dentro

del detector para la correcta orientación de la

batería.

3. Seleccione el sitio de montaje. El máximo es-

pacio entre el detector y el imán es de 1/2" (13

mm).Las ﬂechas ubicadas en el frente de cada

componente deben alinearse y mirarse unas a

otras.El imán debe estar junto al detector.Nota:

Si el imán está empotrado, use el espaciador

para asegurar una alineación correcta.

4. Pruebe el alcance. Antes de montarlos,

sostenga el detector y el imán en el sitio

seleccionado y veriﬁque su funcionamiento.

Mientras sostiene el detector, mueva el imán

lejos del detector para simular una puerta que

se abre. Veriﬁque que el LED rojo del detector

se prenda y se apague momentáneamente y

que la campana suene. Nota: Si el detector no

funciona correctamente, vea la Guía de Análisis

de Averías.

Flechas de alineación

ADVERTENCIA: Para evitar una posible LESIÓN SERIA o la MUERTE:

• NUNCA deje que los niños estén cerca de las baterías.

• Si se ingiere una batería, notiﬁque inmediatamente al doctor.

13 mm

Máximo

Use el espaciador

opcional si es necesario

-10- 595-5724-04

Use el espaciador

opcional si es necesario

5. Monte el detector.

Montaje con tornillos: Fije la tapa posterior

del detector a la pared con los dos tornillos

pequeños (provistos). Presione el detector

sobre la tapa posterior.

Montaje con cinta adhesiva: Fije la cinta

adhesiva de espuma a la tapa posterior del

detector. Pegue la tapa posterior del detector

al marco de la puerta en la posición deseada.

Presione el detector sobre la tapa posterior.

6. Montaje con imán. Repita el paso 5 para ﬁjar

el imán (y el espaciador si es necesario) a la

puerta con los dos tornillos (provistos).Nota: Si

usa el espaciador, use los dos tornillos largos

(provistos).

Altri manuali per 6168

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Heath Zenith Accessori

Heath Zenith

Heath Zenith 5210 Manuale utente

Heath Zenith

Heath Zenith SL-7464-03 Manuale utente

Heath Zenith

Heath Zenith 5867 Manuale di servizio

Heath Zenith

Heath Zenith Hardwired Electronic Chime 598-1313-00 Manuale utente

Heath Zenith

Heath Zenith 7797 Manuale utente

Heath Zenith

Heath Zenith SL-6155 Series Manuale utente

Heath Zenith

Heath Zenith 6180 Series Manuale utente

Heath Zenith

Heath Zenith 6106 Manuale utente

Heath Zenith

Heath Zenith Motion Sensing 3-Way Wall Switch 6107 Manuale utente

Heath Zenith

Heath Zenith SL-6153 Manuale utente

Heath Zenith

Heath Zenith Wireless Christmas Chime 598-1127-03 Manuale utente

Heath Zenith

Heath Zenith 7311 Manuale utente

Heath Zenith

Heath Zenith notifi alert Manuale utente

Heath Zenith

Heath Zenith Decorative Wireless Chime 6180 Manuale utente

Heath Zenith

Heath Zenith 6180 Series Manuale utente

Heath Zenith

Heath Zenith Replacement Motion Sensor SL-5407 Manuale utente

Heath Zenith

Heath Zenith 7776 Manuale utente

Heath Zenith

Heath Zenith Replacement Motion Sensor SH-5407 Manuale utente

Heath Zenith

Heath Zenith InTune MP3 Door Chime Manuale utente

Heath Zenith

Heath Zenith Decorative Wireless Chime 598-1000-07 Manuale utente

Heath Zenith

Heath Zenith DualBrite 5716 Manuale utente

Heath Zenith

Heath Zenith Weatherproof Long Range Wireless Chime with Chime Extender... Manuale utente

Heath Zenith

Heath Zenith Wireless Mechanical Battery Operated Chime... Manuale utente

Heath Zenith

Heath Zenith Lighted Wireless Push Button Accessory Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente