HeatStar HS115IR Istruzioni per il montaggio

Model #

OPERATING INSTRUCTIONS AND OWNER’S MANUAL

READ INSTRUCTIONS CAREFULLY: Read and follow all instructions. Place instructions in a safe place for

future reference. Do not allow anyone who has not read these instructions to assemble, light, adjust or

operate the heater.

This is an unvented gas-fired portable heater. It uses air (oxygen) from the area in which it is used.

Adequate combustion and ventilation air must be provided. Refer to page 3-4.

— Donotstoreorusegasolineorotherflammablevaporsandliquidsinthevicinityofthisoranyother

appliance.

— AnLPcylindernotconnectedforuseshallnotbestoredinthevicinityofthisoranyotherappliance.

— WHATTODOIFYOUSMELLGAS

 • Donottrytolightappliance.

 • Extinguishanyopenflame.

 • Shutoffgastoappliance.

— Servicemustbeperformedbyaqualifiedserviceagency.

If the information in this manual is not followed exactly, a fire or explosion

may result, causing property damage, personal injury or loss of life.

WARNING:

HS115IR

FUEL FIRED PORTABLE RADIANT

CONSTRUCTION HEATER

2 0 1 5 

www.heatstarbyenerco.com800-251-0001

Fuel Fired Portable Radiant Construction Heater Operating Instructions and Owner’s Manual

WARNING:

YOURSAFETYISIMPORTANTTOYOUANDTOOTHERS

PLEASEREADTHESEINSTRUCTIONSBEFOREYOUOPERATE

THISHEATER

GENERAL HAZARD WARNING:

FAILURETOCOMPLYWITHTHEPRECAUTIONSAND

INSTRUCTIONSPROVIDEDWITHTHISHEATER,CANRESULT

INDEATH,SERIOUSBODILYINJURYANDPROPERTYLOSS

ORDAMAGEFROMHAZARDSOFFIRE,EXPLOSION,

BURN,ASPHYXIATION,CARBONMONOXIDEPOISONING,

AND/ORELECTRICALSHOCK.ONLYPERSONSWHOCAN

UNDERSTANDANDFOLLOWTHEINSTRUCTIONSSHOULD

USEORSERVICETHISHEATER.IFYOUNEEDASSISTANCE

ORHEATERINFORMATIONSUCHASANINSTRUCTION

MANUAL,LABELS,ETC.CONTACTTHEMANUFACTURER.

WARNING:

NOTFORHOMEORRECREATIONALVEHICLEUSE

WARNING:

FIRE,BURN,INHALATION,ANDEXPLOSIONHAZARD.

KEEPSOLIDCOMBUSTIBLES,SUCHASBUILDINGMATE-

RIALS,PAPERORCARDBOARD,ASAFEDISTANCEAWAY

FROMTHEHEATERASRECOMMENDEDBYTHEINSTRUC-

TIONS.NEVERUSETHEHEATERINSPACESWHICHDOOR

MAYCONTAINVOLATILEORAIRBORNECOMBUSTIBLES,

ORPRODUCTSSUCHASGASOLINE,SOLVENTS,PAINT

THINNER,DUSTPARTICLESORUNKNOWNCHEMICALS.

THE STATE OF CALIFORNIA REQUIRES THE FOLLOWING WARNINGS:

WARNING: Combustionby-productsproducedwhenusingthisproductcontaincarbonmonoxide,achemical

knowntotheStateofCaliforniatocausecancerandbirthdefects(orotherreproductiveharm).

WARNING: ThisproductcontainschemicalsknowntotheStateofCaliforniatocausecancerandbirthdefects

or other reproductive harm.

TABLE OF CONTENTS

WARNINGS......................................................................2

SPECIFICATIONS...............................................................3

OPERATION...................................................................4-5

TROUBLESHOOTING.........................................................6

WIRINGDIAGRAM...........................................................7

PARTSLIST.......................................................................8

EXPLODEDVIEW..............................................................9

WARRANTY....................................................................11

WARNING:

READ THE INSTRUCTIONS GIVEN IN THIS

MANUAL BEFORE USING THE APPLIANCE.

• DONOTUSEGASOLINE,NAPHTHAORVOL-

ATILEFUELS.

• THEELECTRICALSYSTEMTOWHICHTHE

APPLIANCEISCONNECTEDMUSTCOMPLY

WITHALLSAFETYREGULATIONSINFORCE.

ARESIDUALCURRENTCIRCUITBREAKER

MUSTBEPROVIDEDONTHEMAINDISTRI-

BUTIONBOARD.

• UNPLUGTHEHEATERBEFOREATTEMPTING

ANYSERVICEORMAINTENANCE.

• ALWAYSCHECKTHEPOWERSUPPLYCA-

BLEBEFOREUSE.ITMUSTNOTBEBENT,

CRUSHED,ORINANYWAYDAMAGED.

• THEPOWERSUPPLYCABLEMUSTBERE-

PLACEDONLYBYQUALIFIEDPERSONNEL.

• ONLYUSEANORIGINALPOWERCABLE

WITHWATERPROOFPLUG.

• DONOTTOUCHTHEEXHAUSTGASOUTLET.

DANGEROFBURNS!

Fuel Fired Portable Radiant Construction Heater Operating Instructions and Owner’s Manual

IMPORTANT:

Beforeusingtheheater,readandunderstandallinstruc-

tions and follow them carefully. The manufacturer

is not responsible for damages to goods or persons due to

improper use of units.

GENERAL RECOMMENDATIONS

The heater described in this manual is a portable oil-fueled

infrared heater running on heating oil. Its easy handling

and large fuel tank allow it to be used locally and tempo-

rarily with complete stand-alone operation. The area to

be heated is therefore hit by an even and uniform flow of

heat, without air movement. The unit is a direct combus-

tion heater that works by sending both hot air and combus-

tion products in the room you wish to heat: all the neces-

sary precautions must therefore be taken to guarantee a

sufficient exchange of air.

Always follow local ordinances and codes when using

this heater:

• Readandfollowthisowner’smanualbeforeusingthe

heater;

• THEINSTALLATIONOFTHEUNITSHALLBEINACCOR-

DANCEWITHTHEREGULATIONSOFTHEAUTHORI-

TIESHAVINGJURISDICTIONINYOURAREA.Also,as

a recommended operation practice reference should

bemadetothecurrentissueofCSAB139,Installation

CodeforOilBurningEquipmentinCanadaandNFPA

31StandardfortheInstallationofOil-BurningEquip-

mentIntheUSA;

• Useonlyinplacesfreeofflammablevaporsorhigh

dust content;

• Neveruseheaterinimmediateproximityofflammable

materials(theminimumdistancemustbe10feet);

• Make sure fire fighting equipment is readily available;

• Make sure sufficient fresh outside air is provided ac-

THERMOELECTRIC SPECIFICATIONS

Consumption@0°C

Lb/HR 2.67

Kg/HR 5.88

USGAL/HR 0.849

EFFICIENCY %100

UPPER CALORIFIC VALUE

HEATINPUT

BTU/HR 115,160

Kw 33.5

kcal/h 28,790

HEAToutput

BTU/HR 115,160

Kw 33.5

kcal/h 28,790

LOWER CALORIFIC VALUE

HEATINPUT BTU/HR 109,402

Kw 31.8

kcal/h 27, 351

HEAToutput BTU/HR 109,402

Kw 31.8

kcal/h 27, 351

PUMP PRESSURE

(Factoryset) 174PSI 12bar

SMOKE BACHARACH INDEX

COMBUSTION AIR SETTING

POSITIONHEAD IN 0.126

MM 3.2

NOISE LEVEL @ 3’

AVERAGEDba 69.5

RUN TIME

TANKCAP 11.3GAL

RUNTIME(HOURS) 13.4

OIL NOZZLE

TYPE DELAVAN 80°W

FLOW GPH 0.6

OIL PUMP

TYPE SUNTEC CS30

MOTOR

POWER 200W

CURRENT 3.8A

RPM 3300

OVERHEAT THERMOSTAT

SETPOINT 170°C

ELECTRONIC FLAME CONTROL

MANUFACTURER BRAHMA

TYPE TGRD71

APPROVAL UL

CENTRIFIGUAL FAN

DIAMETER 133MM

METALTHICKNESS 50MM

SUCTIONAIRDISKI.D. 76MM

WHEELS

DIAMETER 9.843"

SHAFTDIAMETER .98"

POWER SUPPLY

INPUT 120 V 60Hz

POWERANDCURRENT

210 W 2.15A FUSE3.15A "T"STYLE

HS115IR WEIGHTS AND DIMENSIONS

DRY

WEIGHT

92.5LB FULL

WEIGHT

173.02LB

LENGTH 35.25"

HEIGHT 31.81"

WIDTH 20.94

SHIPPING DIMENSIONS

LENGTH 29.1" HEIGHT 27.76"

WIDTH 22.4" WEIGHT 104LBS

SPECIFICATIONS

Fuel Fired Portable Radiant Construction Heater Operating Instructions and Owner’s Manual

cording to the heater requirements. Direct combustion

heaters should only be used in well vented areas in

order to avoid carbon monoxide poisoning;

• A rough estimate of opening required for each gallon

(US)ofcapacityisthreesquarefootatheaterlevel,for

direct-fired heaters;

• The heater is installed and connected to properly

grounded electrical outlet with adequate supply. (refer

to specifications for reference.

• Ensurethatthemachinerestingsurfaceorgroundis

not made of flammable material.

• Minimum clearances from combustible material must

be:30”fromsideandrear(airinlet)ofheater80”

fromceiling40”onairoutletofheater.

• Neverblockairinlet(rear)orairoutlet(front);Incase

of very low temperatures add kerosene to the heating

oil;

• Connectthepowercordtotheoutletandwait15min

at least be fore starting heater, to allow pre-heated

filterwarmingheatingoilinsidethefilter(NOTONALL

MODELS)

• Make sure heater is always under surveillance and keep

children and animals away from it;

• Beforestartingtheheateralwayscheckfreerotationof

ventilator;

• Heaterisnotductable.

• Allow heater to fully complete its cooling cycle before

unplugging

• Unplugheaterwhennotinuse.

SAFETY DEVICES

The unit is fitted with an electronic flame control box. In

case of malfunction this box will cut in and stop the heater,

at the same time the reset lamp in the control box will light

up.Referto“ResetButton”sectionforinformation.

Heatersarealsoequippedwithanoverheatthermostat

safety cut out which will stop the heater in case of over-

heating. This thermostat will reset automatically but you

will have to depress button on control panel before being

able to restart the heater.

OPERATION

Beforeanyattemptofstartingtheheaterismade,check

that your electrical supply conforms to the data on the

model plate.

The heater must be placed on a flat, stable and level sur-

facetoavoidmachinetippingand/orgasoilleakagefrom

the tank fuel cap. The flow of heat can be directed upward

withanapproximate10°angle:loosenthetwolocking

knobs (A) and tilt the combustion unit by pressing on the

handle until the desired angle is reached, then lock the

knobs by tightening.

 WARNING:

Beforestart-up,alwaysensuretheguard(B)hasbeencom-

pletely pulled out, so as to guarantee maximum protection

of the machine resting surface.

PUSH UP OR

DOWN TO

ADJUST ANGLE

BURNER ANGLE ADJUSTMENT

FLOOR TEMPERATURE GUARD

Fuel Fired Portable Radiant Construction Heater Operating Instructions and Owner’s Manual

1RESETBUTTONWITHCONTROLLAMP

2CONTROLLAMP

3MAINSWITCH

4ROOMTHERMOSTATPLUG

5POWERCORD

Electrode Gap

Clearances

The following minimum safety clearances from materials or

objects in the surroundings of the heater must be ensured:

 Sides30in. AirInlet30in.

Top 80 in. Air outlet 40 in

• Floorsandceilingsmustbemadeoffireproofmaterials

in the room where the heater is operated

• The air inlet and outlet must never be blocked for any

reason.

• Install the heater on a flat , level floor in a steady

position.

• It is forbidden to connect direct-fired heaters to air

ducts.

CONTROL BOARD

WARNING

• DONOTUSEGASOLINE,NAPHTHAORVOLATILE

FUELS.

• STOPHEATERBEFOREADDINGFUELS.

• ALWAYSFILLOUTDOORSAWAYFROMOPENFLAME

• DONOTUSEEXTERNALFUELSOURCE.

• DONOTOPERATEHEATERWHEREFLAMMABLELIQ-

UIDSORVAPORSMAYBEPRESENT.

• DONOTSTARTHEATERWHENCHAMBERISHOT

• DONOTSTARTHEATERWHENEXCESSFUELHAS

ACCUMULATEDINTHECHAMBER.

• DONOTPLACECOOKINGUTENSILSONTOPOFTHE

HEATER.

• PLUGELECTRICALCORDINTOAPROPERLYGROUND-

EDTHREE-PRONGRECEPTACLE.

STARTING THE HEATER

The heater can only work automatically when a control

device, such as a thermostat or a timer, is connected to the

heater.Connectiontotheheaterismadebyremovingthe

socket cover(4) and inserting the thermostat plug. To start

the machine you must:

• If connected to the thermostat, turn the switch to

(ON+II)thedownposition.

• If not connected to the thermostat, turn the switch to

(ON+I)theupposition.

Whenunitisstartedforthefirsttimeorisstartedafter

the oil tank has been totally emptied, the flow of oil to the

burner may be impaired by air in the circuit. In this case the

control box will cut out the heater and it might be nec-

essary to restart the starting procedure once or twice by

depressingtheresetbutton(1).

Shouldtheheaternotstart,checkthatoiltankisfulland

depressresetbutton(1).

Shouldtheheaterstillnotwork,pleaserefertothetrouble

shooting section of this manual.

RESET BUTTON

This heater is equipped with an internal diagnostics system.

Shouldtheheaternotstartforanyreasontheresetswitch

(1)willilluminate.Inordertoobservethediagnosticblinks

youhavetodepresstheresetbuttonfor10seconds.The

light will then generate a series of blinks that will indicate

why the heater entered a fault mode. Refer to the chart

below for the list of fault codes.

2-BLINKSHeaterfailedtostart

4-BLINKSPhotocellshutdown(lackoflight)

6-BLINKSLossofflameduringoperation

*Refer to Troubleshooting for solutions.

STOPPING THE HEATER

Setmainswitch(3)on“0”positionorturnthermostator

other control device on lowest setting or to a temperature

lower than that of the room it resides.

The flame goes out and the fan continues to work for

approx.90sec.coolingthecombustionchamber.

Fuel Fired Portable Radiant Construction Heater Operating Instructions and Owner’s Manual

MAINTENANCE

Preventive and regular maintenance will ensure a long trou-

ble free life to your heater.

WARNING

• Neverserviceheaterwhileitispluggedin,operatingor

hot.Severeburnsorelectricalshockcanoccur.

Every50hoursofoperation:disassemblethefilterand

wash with clean oil, remove upper body parts and clean

inside and ventilator with compressed air, check for the

correct attachment of the connectors to the electrodes and

check all cables, remove burner assembly, clean and check

electrode settings, adjust according to figure

“ElectrodeGap”.

SAFETY DEVICES

This heater is equipped with an overheat thermostat safety

cutout which will stop the heater in case of overheating.

This thermostat will reset automatically but you will have

todepressbutton(1)oncontrolboxbeforebeingableto

restart the heater.

WARNING

• Before making any attempt to restart the heater

find and eliminate the reason

TRANSPORT

Beforeheaterismoveditmustbestoppedandunplugged.

Beforemovingtheheaterwaittillithastotallycooledoff

and make sure oil tank cap is securely fixed.

OBSERVED FAULT CAUSE REMEDY

Motor does not start, no ignition

Noelectricalcurrent

Checkmainpowersupply

Checkproperpositioningandfunctionofswitch

Checkfuse

Wrongsettingofroomthermostator

other control

Checkcorrectsettingofheatercontrol.Ifthermostat,

make sure selected temperature is higher than room

temperature

Thermostat or other control defective Replace control device

Electricalmotordefective Replace motor

Electricalmotorbearingsdefective Replace motor

burned out condenser Replace condenser

Motor starts, no ignition or cuts out

Electricignitordefective CheckconnectionofH.TLeadstoelectrodesand

transformer

Checkelectrodessetting

Checkelectrodeforcleanliness

ReplaceH.T.transformer

Flamecontrolboxdefective Replace control box

Photocell defective Cleanorreplacethephotocell

Notenoughornofuelatburner Checkstateofmotor-pumpplasticcoupling

Checkfuellinesystemincludingfuelfilterforpossible

leaks

Cleanorreplaceoilnozzle

SolenoidDefective Checkelectricalconnection

Cleanorreplacesolenoid

Motor starts, heater emits smoke

Notenoughcombustionair Make sure Air inlet and outlet are free

Checksettingsofcombustionairflap

Cleanburnerdisc

Too much combustion air Checksettingsofcombustionairflap

Fuelcontaminatedorcontainswater Replace fuel in tank with clean fuel

Cleanorreplaceoilfilter

Air leaks in fuel circuit Checkfuellineandfilterforpossibleleaks

Notenoughfuelatburner Checkpumppressure

Cleanorreplacefuelnozzle

Too much fuel at burner Checkpumppressure

Replacenozzle

Heaterdoesnotstop Solenoiddefective Replace solenoid

TROUBLESHOOTING

IFYOURUNITISSTILLNOTWORKINGLOCATETHENEARESTAUTHORIZEDSERVICECENTERORCONTACTHEATSTARAT800-251-0001

Fuel Fired Portable Radiant Construction Heater Operating Instructions and Owner’s Manual

WIRING DIAGRAM – SCHEMA ELECTRIQUE

AP CONTROL BOX

C OFFRET DE SECURITE

TA R OOM THERMOSTAT PLUG

P RISE THERMOSTAT D’AMBIANCE

LI1 O VERHEAT THERMOSTAT

T HERMOSTAT DE SURCHAUFFE

EV1 SOLENOID VALVE

E LECTROVANNE

FO P HOTOCELL

P HOTORESISTANCE

CO C APACITOR

C ONDENSATEUR

MV B URNER MOTOR

M OTEUR BRULEUR

FUA FUSE

F USIBLE

RV S WITCH

COMMUTATEUR

ST E LECTRIC PILOT

LAMPE TEMOIN D’ALIMENTATION

RF HEATED FILTER >> OPTIONAL

F ILTRE GASOIL RECHAUFFE

RL RESET BUTTON

BOUTON REARMEMENT

LL LOCK OUT INDICATOR LIGHT

RV1 SWITCH

COMMUTATEUR

TD T RANSFORMER H.V.

TRANSFORMATEUR H.T.

LI1

EV1

FUA

RV1

CONTROLBOX

ROOMTHERMOSTATPLUG

SOLENOIDVALVE

OVERHEATTHERMOSTAT

PHOTOCELL

CAPACITOR

BURNERMOTOR

FUSE

SWITCH

ELECTRICPILOT

HEATEDFILTER(OPTIONAL)

RESETBUTTON

LOCK-OUTINDICATOR

TRANSFORMERH.V.

SWITCH

Fuel Fired Portable Radiant Construction Heater Operating Instructions and Owner’s Manual

POS P/N ALT# DESCRIPTION

01 G 110 51 PROTECTIVEPANEL

02 G 110 5 2 FRONTDISC

03 G 11 0 5 3 INSULATINGPANEL

04 G11054 COMBUSTIONCHAMBER

05 G 110 55 REARDISC

06 G11056-N500 UPPERPROTECTIVEPANEL

07 M20820 SPACER

08 G11057-9010 BODY

09 C10714 HANDWHEEL

10 G11058 BLASTTUBE

11 50 413 E20671 TERMINALBOARD

12 50214 C 30361 PIPECAP

13 P20304-9005 HANDLE

14 G11059-9010 PANEL

15 G11060-9010 PANEL

16 C30383 TANKCAP

17 P50150 FUELTANK

18 50 413 C30375 O-RING

19 50428 I25020 DRAINCAP

20 G11061-9010 PANEL

21 G11062-9010 PANEL

22 G11063-9010 PANEL

23 G11064-N500 LOWERPROTECTIVEPANEL

24 I40347 FLEXDIESELPIPE

25 C30729 CLIP

26 50314 I 30 414 FILTER

27 I40327 FLEXDIESELPIPE

28 I40348 FLEXDIESELPIPE

29 50061 I30696 SUCTIONPIPE

30 50063 I30737 BRASSFITTING

31 G11065-9005 SUPPORT

32 G11066-9005 WHEELAXLE

33 C10504 WHEEL

34 50226 M20204 ELASTICWASHER

35 50318 C10513-N BLACKWHEELCOVER

36 T20375 NOZZLE

37 G11069 AIRFLAP

38 G11068 DIFFUSERRING

39 G 1107 0 AIRADJUSTMENTDISC

40 50104 E10248 IGNITIONELECTRODE

41 50247 G 110 2 0 ELECTRODESSUPPORTSTIRRUP

42 50131 I31034 BRASSLOCKNUT

43 G 11071 BURNERSUPPORTDISC

44 50336 E50327 PHOTORESISTORSUPPORT

45 50323 E50328 PHOTOCELL

46 G02089 H.T.CABLECONNECT.

47 50522 C30368 CABLEPROTECTION

48 50232 I40339 MICROPIPE

49 50 414 E50109 SAFETYTHERMOSTAT

50 50430 I33007 NOZZLESUPPORT

51 G11072-9010 EL.CONTROLBOXPANEL

52 5 0 013 E10102-P SWITCH

53 E10140 RESETBUTTON

54 50009 E30443-1 POWERCORD

55 E20964 CABLEFASTENER

56 E20965 CABLEFASTENERNUT

57 E20319 GROUNDTERMINALBOARD

58 E 11 0 33 LAMP

59 5 0 3 11 E40125 FLAMECONTROLBOX

60 50570 E20640 THERMOSTATPLUG

61 5 0 011 E20665 THERMOSTATPLUGCOVER

62 C10331 ELBOWCONNECTION

63 C10323 SCROLL

64 T10296 FAN

65 G11073-9010 FANSUPPORTBRACKET

66 G11074-9010 MOTORSUPPORTBRACKET

67 E10769 MOTOR

68 E10769-1 CAPACITOR

69 50237 E10698 MOTOR-PUMPCOUPLING

70 50729 I20104 IRONFITTING

71 50132 I 2 0115 IRONFITTING

72 T20448 DIESELPUMP

73 50141 T 2 0117 SOLENOIDVALVEBODY

74 5014 0 T 2 0118 SOLENOIDCOIL

75 50433 T20442 SOLENOIDVALVECABLE

PARTS ORDERING INFORMATION:

PURCHASING: AccessoriesmaybepurchasedatanyHeat-

star local dealer or direct from the factory

FOR INFORMATION REGARDING SERVICE

PleasecallToll-Free800-251-0001

www.heatstarbyenerco.com

Ourofficehoursare8:00AM–5:00PM,EST,Monday

throughFriday.

Please include the model number, date of purchase, and

description of problem in all communication.

Fuel Fired Portable Radiant Construction Heater Operating Instructions and Owner’s Manual

36 37 38 39 40

41 43 45

49 47

48 46

17 16

22 14

Optional

57 59

53 58

55 56

70 71

WARNING:

USEONLYMANUFACTURER’SREPLACEMENTPARTS.USEOFANYOTHERPARTSCOULD

CAUSEINJURYORDEATH.REPLACEMENTPARTSAREONLYAVAILABLEDIRECTFROM

THEFACTORYANDMUSTBEINSTALLEDBYAQUALIFIEDSERVICEAGENCY.

PARTS ORDERING INFORMATION:

PURCHASING: AccessoriesmaybepurchasedatanyHeatstar/Mr.Heaterlocaldealeror

direct from the factory

FOR INFORMATION REGARDING SERVICE

PleasecallToll-Free800-251-0001•www.heatstarbyenerco.com

Ourofficehoursare8:00AM–5:00PM,EST,MondaythroughFriday.

Please include the model number, date of purchase, and description of problem in all

communication.

LIMITED WARRANTY

The company warrants this product to be free from imperfections in material or workmanship,

undernormalandproperuseinaccordancewithinstructionsofTheCompany,foraperiodof

threeyearsonparts(limited)and10yearsontheheatexchanger,fromthedateofdeliveryto

thebuyer.TheCompany,atitsoption,willrepairorreplaceproductsreturnedbythebuyertothe

factory,transportationprepaidwithinsaidoneyearperiodandfoundbytheCompanytohave

imperfections in material or workmanship.

Ifapartisdamagedormissing,callourTechnicalSupportDepartmentat800-251-0001.

AddressanyWarrantyClaimstotheServiceDepartment,HeatstarbyEnerco,4560W.160THST.,

CLEVELAND,OHIO44135.Includeyourname,addressandtelephonenumberandincludedetails

concerning the claim. Also, supply us with the purchase date and the name and address of the

dealer from whom you purchased our product.

TheforegoingisthefullextentoftheresponsibilityoftheCompany.Therearenootherwarranties,

expressorimplied.Specificallythereisnowarrantyoffitnessforaparticularpurposeandthere

isnowarrantyofmerchantability.InnoeventshalltheCompanybeliablefordelaycausedby

imperfections, for consequential damages, or for any charges of the expense of any nature incurred

without its written consent. The cost of repair or replacement shall be the exclusive remedy for any

breach of warranty. There is no warranty against infringement of the like and no implied warranty

arising from course of dealing or usage of trade. This warranty will not apply to any product which

has been repaired or altered outside of the factory in any respect which in our judgment affects its

condition or operation.

Somestatesdonotallowtheexclusionorlimitationofincidentalorconsequentialdamages,sothe

abovelimitationorexclusionmaynotapplytoyou.ThisWarrantygivesyouspecificlegalrights,and

you may have other rights which vary from state to state.

Heatstar,INC.,4560W.160THST.,CLEVELAND,OHIO44135•800-251-0001

HEATSTARisaregisteredtrademarksofENERCOGROUP,Inc.

HeatstarbyEnercoreservestherighttomakechangesatanytime,withoutnoticeorobligation,

in colors, specifications, accessories, materials and models.

OPERATING INSTRUCTIONS

AND OWNER’S MANUAL

READ INSTRUCTIONS CAREFULLY: Read and follow all instructions. Place instructions in a safe

place for future reference. Do not allow anyone who has not read these instructions to assemble,

light, adjust or operate the heater.

HS115IR

Model #

PRODUCTREGISTRATION:Thankyouforyourpurchase.

Pleaselogintohttp://www.egiregistration.comtoregisteryourproduct.

ANSI Z83.7b/CGA 2.14b-2009

Indice

Lingue:

Altri manuali HeatStar Stufa

HeatStar

HeatStar THP750S Manuale utente

HeatStar

HeatStar HS60CLP Istruzioni per il montaggio

HeatStar

HeatStar HSVFBF10NG Istruzioni per il montaggio

HeatStar

HeatStar ERSP-40 Istruzioni per il montaggio

HeatStar

HeatStar HSU50NG Istruzioni per il montaggio

HeatStar

HeatStar HS80CVNG Istruzioni per il montaggio

HeatStar

HeatStar HSSVFRD20LPBT Istruzioni per il montaggio

HeatStar

HeatStar HSVFRD20NGBTS Istruzioni per il montaggio

HeatStar

HeatStar HS 3500DF Istruzioni per il montaggio

HeatStar

HeatStar HSRR30SP(LP) Istruzioni per il montaggio

HeatStar

HeatStar HS100CVNG Istruzioni per il montaggio

HeatStar

HeatStar ERSP-60 Istruzioni per il montaggio

HeatStar

HeatStar HS18CH Istruzioni per il montaggio

HeatStar

HeatStar HS4000 NG/LP Istruzioni per il montaggio

HeatStar

HeatStar HS50K Istruzioni per il montaggio

HeatStar

HeatStar HSU200NG Istruzioni per il montaggio

HeatStar

HeatStar HSU50 Istruzioni per il montaggio

HeatStar

HeatStar HSP500ID-A Manuale

HeatStar

HeatStar HSVFRD10NG Istruzioni per il montaggio

HeatStar

HeatStar ERXL-40 Istruzioni per il montaggio

HeatStar

HeatStar HS50KPA Istruzioni per il montaggio

HeatStar

HeatStar HS400FAVT Istruzioni per il montaggio

HeatStar

HeatStar HSU100NGPALP Istruzioni per il montaggio

HeatStar

HeatStar HSP60R Istruzioni per il montaggio

Manuali Stufa popolari di altre marche

oventrop

oventrop Regucor Series Manuale utente

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuale utente

ELMEKO

ELMEKO ML 150 Manuale utente

BN Thermic

BN Thermic 830T Manuale utente

KING

KING K Series Guida

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guida rapida

Well Straler

Well Straler RC-16B Manuale utente

EUROM

EUROM 333299 Manuale utente

Heylo

Heylo K 170 Manuale utente

Eterna

Eterna TR70W Manuale utente

Clarke

Clarke GRH15 Manuale di istruzioni

IRSAP

IRSAP The Radiator Company Ovali Manuale utente

Empire Heating Systems

Empire Heating Systems WCC65 Manuale utente

Wetekom

Wetekom 92 86 43 Manuale utente

Desa

Desa SPC170-F Manuale utente

Watlow

Watlow Watrod Electric Tubular Heaters Manuale utente

Haverland

Haverland ECO-DRY GPS Series Manuale elenco delle parti

Stelpro

Stelpro ASILVC2060 Series Manuale utente