HELVAR Digidim 458 Manuale utente

Digidim 458

Digidim 458Digidim 458

Digidim 458

-Channel

ChannelChannel

Channel

Dimmer

DimmerDimmer

Dimmer

STEP

STEPSTEP

STEP 6

Set SDIM

Addresses

STEP

STEPSTEP

STEP 5

Replace Cover

& Power Up

Unit

STEP

STEPSTEP

STEP 4

Attach Module

and Make

Connections

STEP 3

STEP 3STEP 3

STEP 3

Electrical

Installation

STEP 2

STEP 2STEP 2

STEP 2

Mount Dimmer

Chassis

STEP 1

STEP 1STEP 1

STEP 1

Disassemble

Dimmer Unit

READY FOR USE

INSTALLATION GUID

INSTALLATION GUIDE

INSTALLATION GUID

Digidim 458 Dimmer Installation Guide Helvar Ltd.

Doc. No. 7860186 Page 1 Issue 1 (10/7/2008)

Step 1 Disassemble Dimmer Unit

1.1. Remove Cover

2) Remove

screws to

left of door

3) Remove cover from

chassis

1) Open door and

remove screws from

inside door

1.2. Detach Dimmer Module and Remove Knockouts

1. Partially unscrew the two knobs.

2. Remove the module from the chassis.

3. Remove the knockouts. Use the grommets provided to protect cabling going

through the knockouts. If necessary, the knockout gland plates can be removed to

provide more space for cabling.

Module mounting bracket

Unscrew knobs

Knockouts

Digidim 458 Dimmer Installation Guide Helvar Ltd.

Doc. No. 7860186 Page 2 Issue 1 (10/7/2008)

311

363

Note: All dimensions in mm

178

Step 2 Mount Dimmer Chassis

2.1. Mounting Requirements

Mounted vertically on a flat surface.

A clearance of at least 50 mm on all sides of the unit to allow for adequate

ventilation. The grilles must NOT be obstructed.

Sufficient clearance must be left to allow for the connection of cables and trunking.

The ambient temperature must be within the range of 0ºC to 40ºC and the area

must be adequately ventilated.

Humidity must be within the range of 0% to 90% (non-condensing). Do NOT install

this product in a damp location.

2.2. Mounting Procedure

Use 4 screws (not provided) to mount to

the wall (No.8 or No. 10 screws with a head

diameter greater than 6 mm and less than

9 mm).

Note 1 Use the mounting holes located

at the furthest corners of the

chassis.

Note 2: If you are replacing an Imagine

dimmer, e.g.HES99400, and are

using the existing screw

locations, then you can use the

two holes at the top and the two

in the middle.

Note 3: Use wall plugs, if necessary.

180

280

230

31.5

41.5

to edge of

dimmer

module

41.5

Note: All dimensions in mm

clearancefor

ventilation

Digidim 458 Dimmer Installation Guide Helvar Ltd.

Doc. No. 7860186 Page 3 Issue 1 (10/7/2008)

Step 3 Electrical Installation

WARNING: BEFORE COMMENCING ANY ELECTRICAL WORK, ISOLATE THE

ELECTRICITY SUPPLY AT THE MAIN DISTRIBUTION BOARD.

Mains Supply Voltage Range

The dimmer is designed for use with the following voltage range:

85 to 264 VAC (absolute); 110 VAC / 230 VAC (nominal).

Mains Supply Protection

The mains supply input must be externally protected by an MCB or fuse of a suitable

rating.

WARNING: THE SUPPLY INPUT MUST ONLY BE CONNECTED TO A SINGLE-

PHASE SUPPLY. THE SUPPLY INPUT EARTH MUST BE CONNECTED.

Using Spring-Lever Cage Clamp Terminals

Note: The supply earth, supply neutral and output terminals are spring-lever cage

clamp terminals.

1. Insert a screwdriver as far as it will go into the terminal release point.

2. Lever the screwdriver back. This opens the cage clamp. (For output terminals,

levering the screwdriver back is unnecessary).

3. With the cage clamp open, cable can be inserted or removed from the terminal.

4. Release the pressure on the screwdriver and then remove it. This closes the cage

clamp. If you have inserted a cable, check that the connection is secure.

Digidim 458 Dimmer Installation Guide Helvar Ltd.

Doc. No. 7860186 Page 4 Issue 1 (10/7/2008)

3.1. Connect the Mains Supply Input

Connect the mains supply input to the MCB and earth and neutral terminals, as shown

in the diagram below.

3.2. Connect the Loads

Connect the loads to the output terminals, as shown below.

SUPPLY EARTH

SUPPLY LIVE

Miniature Circuit Breakers (MCBs)

MAINS SUPPLY INPUT

SUPPLY NEUTRAL

EARTH

OUTPUT TERMINALS

NEUTRAL

OUTPUTS

LIVE

OUTPUTS

54321

Dimmed

Load

Copper Bus Bar

(live supply to all channels)

Digidim 458 Dimmer Installation Guide Helvar Ltd.

Doc. No. 7860186 Page 5 Issue 1 (10/7/2008)

Step 4 Attach Module and Make Connections

WARNING: BEFORE ATTACHING THE MODULE AND MAKING ANY

CONNECTIONS, ENSURE THAT THE MAINS SUPPLY IS STILL ISOLATED.

Re-assemble the dimmer module to the chassis before making any connections.

4.1. Connect Module Supply and Dimmer Channels

1. Remove the cables from the bypass terminals and connect them to the channel

terminals.

(Ensure that the terminal numbers correspond to the channels numbers).

2. Connect the supply to the module.

Note: The bypass terminals allow operation and testing of the lights and installation

wiring. The supply cable is supplied disconnected.

Channel Output

Channel Input

Dimmer Channels 1 - 8

Bypass

connection

terminals

Dimmer mains

supply terminal

Use cable sleeving over these signal wires

Options module

connection socket

Digidim 458 Dimmer Installation Guide Helvar Ltd.

Doc. No. 7860186 Page 6 Issue 1 (10/7/2008)

4.2. Make Necessary Control Connections

DALI

SDIM

Link for

termination

Close for

Override

Link for DALI

power

SCN 0V ATERM B DA+ DA-

Touch

Panel Power

/OVR

Power

Link

Override

The dimmer may be controlled by either DALI or S-DIM, but DO NOT CONNECT

BOTH AT THE SAME THE TIME.

Note: Use the cable sleeving (supplied) to provide an extra layer of insulation

between the S-DIM, TouchPanel and Override low voltage signal wires and

other wiring.

S-DIM

If connecting to an Imagine system, connect to the S-DIM terminals.

If the dimmer is at the end of the S-DIM cable, wire between the ‘TERM’ and ‘B’

connections of the S-DIM terminals to enable the cable termination.

TouchPanel

You can supply one TouchPanel from the TouchPanel power connection terminal.

Override

If you wish to provide output level override functionality, wire between the ‘–/0V’ and

‘OVR’ connections of the override input connection terminal. This sets the light output

of all dimmer channels to the override level (the default is 100%, but can be changed).

DALI

If connecting to a Digidim system, use the DALI connector.

If the built-in 250mA DALI power supply is required, wire between the ‘+’ and

‘Power Link’ terminals of the DALI connector to provide DALI power.

REMEMBER THAT YOU CANNOT EXCEED THE DALI POWER SUPPLY OF 250 mA.

4.3. Check Connections

Check that all the necessary connections have been made correctly and securely

Step 5 Replace Cover & Power Up the Unit

1. Replace the cover using the original screws. (Screw size = M4x6).

2. Power up the dimmer unit by switching on the MCBs.

3. Check that the display screen lights up and the dimmer channel levels appear.

Digidim 458 Dimmer Installation Guide Helvar Ltd.

Doc. No. 7860186 Page 7 Issue 1 (10/7/2008)

Step 6 Set SDIM Addresses

If the dimmer is connected to a system through its SDIM connection terminal, the

SDIM addresses must be set as follows:

Display Procedure

Upon power up of the unit, the LCD

‘Display Screen’ appears.

Access Addresses Menu

From the Control Panel of the dimmer module:

1) Press on the keypad to access ‘Main Menu’.

2) In ‘Main Menu’, with the arrow pointing at

‘Addresses’,

press .

The ‘Addresses’ menu appears, listing

the addresses for S-DIM and DALI.

Set SDIM base address

1) At ‘Set SDIM base’, press .

2) Press or to select a base address

and press to enter.

3) Press to return to ‘Addresses’ menu.

Note: The base address is the first channel address,

from which the remaining addresses follow

consecutively (unless changed manually in the ‘SDIM

address’ sub-menu, see procedure below).

Set SDIM addresses (optional)

If you wish to set the addresses individually:

1) Press ‘down’ to select ‘SDIM addresses’ and press

2) Press or to select a channel and

press to enter.

3) Press or to select an address and

press to enter.

4) Press and hold to return to ‘Main Menu’.

The S-DIM addresses are now set and the unit is operational.

- ADDRESSES -

Set SDIM base

SDIM address

- ADDRESSES -

Set SDIM base

SDIM address

- MAIN MENU -

Addresses

About product

12345678

Dimmer

Digidim 458 Dimmer Installation Guide Helvar Ltd.

Doc. No. 7860186 Page 8 Issue 1 (10/7/2008)

Technical Data

Mains supply voltage: 85 VAC to 264 VAC

Supply frequency:

Protection:

45 Hz to 65 Hz

4 of 10 A MCBs for loads, 4 A MCB and PTC for control board (MCB

type C 10 kA)

Output regulation:

Supply current:

Nominal load:

DALI Supply:

TouchPanel Supply:

Automatic compensation for supply voltage and frequency variations

40 A (max)

8x5 A or 4x10 A loads

250 mA (max), 16 VDC (nominal)

Conformity & Standards

EMC – Emission:

Immunity:

Safety – Safety:

Isolation:

IP rating:

Data transfer requirements

– DALI:

– S-DIM:

Environmental:

EN 55015

EN 61547

EN 60950

4 kV

EN 60929

Helvar protocol (RS485, 115 kbps)

Complies with WEEE and RoHS

Power consumption (excluding loads):

Thermal protection:

Installation:

1.3 W (with no DALI or TouchPanel PSUs used)

Control board – resettable fuse, power devices – thermal sensing

Vertically-mounted using four 4.5 mm mounting holes

Weight:

Dimensions (in mm):

Operating conditions

Temperature range:

Humidity:

11 kg

363 (L) x 311 (W) x 178 (D)

Storage temp. -10ºC to 70ºC

Ambient operating temp. 0ºC to 40ºC

90% max. (no condensation)

Cable Requirements

Note: DALI cable must be mains-rated and the maximum voltage drop along the

length of the cable must not exceed 2V.

Connection Cable Type Cable Length

Dimmer Mains Supply Solid core up to 10 mm

stranded up to 10 mm

N/A

Dimmer Channel Outputs Solid core up to 4 mm

stranded up to 2.5 mm

N/A

DALI 1.0 mm

to 1.5 mm

(recommended)

Note: Supply output 250 mA (nom)

max. 300 m

@ 1.5 mm

S-DIM Low loss RS485 type; multi-stranded,

twisted and shielded; 3 or 4 core plus

screen; 0.22 to 1.5mm

Recommended: one or two twisted pairs

(screened and earthed) e.g. ‘Belden 8102’

max. 1000 m

(without

repeater)

Override Screened, twisted pair, 0.5 mm

to 1.5 mm

max. 50 m

Helvar Ltd

Hawley Mill

Hawley Road

Dartford, Kent DA2 7SY, UK

Tel: +44 1322 222 211

Fax: +44 (0)1322 282 216

www.helvar.com

8-Channel Dimmer

Product: 458

Doc No. 7860186

Issue 1

Date: 10/07/2008

Indice

Altri manuali HELVAR Dimmer

HELVAR

HELVAR HES99300 Manuale utente

Manuali Dimmer popolari di altre marche

ZooZ

ZooZ ZEN54 LR Manuale utente

Lex

Lex 6KW Manuale utente

DIODE LED

DIODE LED TOUCHDIAL Mini Manuale utente

Viessmann

Viessmann 5590 Manuale utente

American DJ

American DJ DP-8A Manuale utente

Teleco

Teleco TVSTICK868RGB29 Manuale utente

INSTEON

INSTEON LampLinc 2457D2 Manuale utente

LEGRAND

LEGRAND WattStopper RH703PTU Manuale utente

ADB

ADB EURODIM TWIN TECH Manuale utente

Sinope

Sinope DM2550ZB-C4 Manuale utente

SkyLink

SkyLink SK7 Manuale utente

Makel

Makel RC Manuale utente

Lightronics

Lightronics XC-62 Manuale utente

Triton Blue

Triton Blue DM-1225 Manuale utente

ETC

ETC ES750 Istruzioni operative

NA OMEGA + Manuale utente

GE ZB3001 Manuale utente

LSC

LSC DP-1210 Manuale utente