Henri Studio 5231F21 Istruzioni utente

SETTING UP THE

5231F21

1) Place 6719 Fiberglass Pool on your prepared

surface.

2) Check the standpipe in the 6719 pool center to make sure it is tight. Place pump in center of pool

and feed power cord through attached standpipe and (using channel area built under pool) out to

desired area outside of pool. Open the slit in the large rubber stopper, place around the power cord

near the top of the standpipe, close the slit, then press into the pipe to make it

watertight. Insert largest barbed adapter into the pump exhaust. Attached

18” tube and clamp it tight to the adapter.

3) With help, place the 7234 Base in the center of the

fiberglass pool, making sure to pull the tube safely up

through it.

4) Thread the two Bushings into the top and bottom of

the coupling in the 6234 Bowl’s floor, then thread a 1”

Barbed Adapter into each of the bushings. Set the

6234 bowl on the base, pushing and clamping

the tube onto the bottom barb as you set it

down. Attach the 8” x 1” clear tube to the barb

inside this bowl. Push the other end of the tube

over the straight leg of the 1” tee. Push the 4”

x 1” tube over the opposing straight leg of the

tee and push the 1” x 1” tube sleeve over the

middle leg of the tee. Insert the Elbow into the

1” tube sleeve and then press the ¾” x 4” long

clear tube over the barbed end of the elbow.

Position a flow Restrictor over the ¾” x 4”

tube and tighten it just enough to stay in place.

(Later, you can tighten the restrictor further if you

want to adjust down the water flow.)

5) Set the 7232 Base into the 6234 bowl. Insert

a 1” Barbed Adapter into the bottom of the

6232 Bowl and insert the smaller ¾” Barbed

Adapter into the top side of the same

bowl. Set the 6232 onto the 7232 base,

pressing the open end of the 1”

x 4” tube over the adapter’s

barbed underneath.

6) Build another tee assembly similar to the one in the bowl below. This time, attach a ¾” x 8”

flexible tube onto each leg of the ¾” Tee. Position and slightly tighten a flow Restrictor over the

tube on the middle leg of the tee. Then push the open end of a tube on a straight leg over the barb

inside the bowl.

Make sure to place your fountain on a firm and level

surface which will not settle. Note: Always follow

local electrical codes and use a 110V GFCI protected

outlet. Do not let children climb on fountain.

7) Insert two ¾” Barbed Adapters in the top and underside of the 6231 Bowl/Base unit. Attach the

12” tube to the top adapter. As you lower the bowl/base unit into place, push the other end of the

tube from the tee below (not the restricted tube) onto the barbed adapter under the 6231 unit.

8) Place the 5231 Finial within the top of the 6231 bowl/base unit. As you lower the finial into

place, slip the top of the 12” tube up inside of the finial.

9) Now, install the 6233A and 6233B ledge rim sections in alternating order on the top edge of the

large 6234 bowl. A steel strapping system is provided to hold these securely in place and caulk is

provided for you to make a water tight seal (so the water will spill over the rim sections rather than

through them). Remove the bolts provided under the rim edges and above the bowl edge. Hold a

slotted strap against the top edge of the 6234 bowl and bolt in, using the washers between the head

of the bolt and the strap. Apply caulk generously to the top edge of the 6234 bowl. Set one of the

rim edges in place and insert a bolt (with washer) from the bottom up into the bolt hole under the

middle of the rim edge and tighten. Apply caulk to the left and right ends of the ledge rim section

(all the way up to the highest level of the end. Repeat until all the rim edges are on.

10) While allowing the caulk some time to cure (see caulk instructions) place the 9029a and 9029b

Toscano Pool Surrounds around the pool in alternating sequence.

11) After filling the pool and bowls of the fountain with water, read your pump instruction. Then

connect the pump to a GFCI protected. Turn on the pump and check for balance. If necessary, use

shims to adjust bowls (starting from bottom up).

You can tighten restrictors now if you desire to

adjust the water flow from any section.

Csd

11/2022

Online Resources

Products: www.henristudio.com/products

FAQs: www.henristudio.com/faq

Warranty: www.henristudio.com/warranty

Contact : www.henristudio.com/contact-us

Caution: The use of Chlorine or Chlorine Bleach or water

coloring additives may damage the finish of your fountain.

IMPORTANT – WINTER CARE

Winter ice build-up can cause damage to concrete statuary. Follow

these tips to reduce winter weathering to your fountain:

* Disconnect power to pumps and any lights.

* Remove plugs/stoppers in all fountain bowls to open drains and let

all moisture out. Keep drains open throughout winter.

* Cover with a Henri fountain cover. Keep tight and do not let snow

or water collect in sagging areas.

* Do not allow snow or ice to build up on or against the concrete.

Remove snow before it turns to ice. Do not use antifreeze, salt or

chemical ice removers as these may damage concrete.

Indice

Altri manuali Henri Studio Fontana da esterno

Henri Studio

Henri Studio Palazzo Venus Manuale utente

Henri Studio

Henri Studio 5661F Manuale utente

Henri Studio

Henri Studio 5701F2 Manuale utente

Henri Studio

Henri Studio 4006F17 Istruzioni utente

Henri Studio

Henri Studio 5649F15 Manuale utente

Henri Studio

Henri Studio Large Rock Falls Fountain Manuale utente

Henri Studio

Henri Studio 5595F14 Istruzioni utente

Henri Studio

Henri Studio Rock Falls 5887F2 Manuale utente

Henri Studio

Henri Studio 4012F2 Manuale utente

Henri Studio

Henri Studio 4005F3 Istruzioni utente

Henri Studio

Henri Studio 5501F6 Istruzioni utente

Henri Studio

Henri Studio 4946F1 Istruzioni utente

Henri Studio

Henri Studio 5452F Guida rapida

Henri Studio

Henri Studio 5887F3 Istruzioni utente

Henri Studio

Henri Studio 5705F7 Manuale utente

Henri Studio

Henri Studio 5513F20 Istruzioni utente

Henri Studio

Henri Studio 4875A Manuale

Manuali Fontana da esterno popolari di altre marche

Sunnydaze Decor

Sunnydaze Decor XSS-578 Manuale utente

Campania International

Campania International Bibendum FT-400 Manuale utente

Elkay

Elkay FLEXI-GUARD EFHA8 1M Series Manuale di installazione

S.R.Smith

S.R.Smith Color Light Stream 2CLSLBK Manuale utente

Hozelock Cyprio

Hozelock Cyprio Cascade 1500 Manuale utente

Campania International

Campania International Juliet Fountain Manuale utente

YARDART

YARDART FT-155 Manuale utente

Alpine

Alpine WIN732 Manuale utente

Campania

Campania Valencia Manuale utente

Campania International

Campania International FT-320 Manuale utente

GardenWize

GardenWize SWGSL230 Manuale utente

Kelkay

Kelkay Easy Fountain Rustic Windmill Manuale utente

Alpine

Alpine WIN258 Manuale utente

Bond

Bond Signature Series Manuale utente

Kenroy Home

Kenroy Home 51112COPBL Guida all'installazione

EasyPro

EasyPro Tranquil Décor HBB39 Manuale utente

Angelo Decor

Angelo Decor Castillo Manuale utente

Campania International

Campania International Girona FT-102A Manuale utente