TABLE OF CONTENTS Translation of the original operating instructions HERMA 400
8/130 3.26 EN (200416)
7.1.1 List of malfunctions (indicated via display) 104
7.1.1.1 SM106 Missing label at dispensing beak 104
7.1.1.2 SM107 End of label web 104
7.1.1.3 SM108 Dispensing unit does not reach home position 104
7.1.1.4 SM109 Dispensing unit does not leave home position 104
7.1.1.5 SM110 Dispensing unit does not reach work position 104
7.1.1.6 SM111 Dispensing unit does not leave work position 104
7.1.1.7 SM113 Transfer unit does not reach home position 104
7.1.1.8 SM114 Transfer unit does not leave home position 105
7.1.1.9 SM115 Transfer unit does not reach work position 105
7.1.1.10 SM116 Transfer unit does not leave work position 105
7.1.1.11 SM119 Label check Error after label feed 105
7.1.1.12 SM120 Label check Error after label transfer 105
7.1.1.13 SM134 Printer fault 105
7.1.1.14 SM141 Undefined movement of label web 105
7.1.1.15 SM148 Missing label series fault (web break?) 106
7.1.1.16 SM153 Multi labelling Start sequence too close 106
7.1.1.17 SM154 Batch finished! 106
7.1.1.18 SM162 Start delay too low or vMax was exceeded 106
7.1.1.19 SM163 Start sequence too close 106
7.1.1.20 SM164 Start signal Sensor mark not detected 106
7.1.1.21 SM165 Roller unit Communication error 106
7.1.1.22 SM166 Applicator Communication error 106
7.1.1.23 SM167 Roller unit Error 106
7.1.1.24 SM168 CAN connection Disconnect! 106
7.1.1.25 SM169 Firmware update required! 107
7.1.1.26 SM170 Bluetooth Initialization error! 107
7.1.1.27 SM171 Bluetooth H400 S/N required! 107
7.1.1.28 SM180 Printer not finished 107
7.1.1.29 SM181 Chip changed! 107
7.1.1.30 SM185 Firmware update Winder required 107
7.1.1.31 SM198 CAN communikation Response time 107
7.1.1.32 SM199 CAN communication no CAN module detected 107
7.1.1.33 SM805 Unwinder failure TEACH process 107
7.1.1.34 SM808 Unwinder failure Too slow 107
7.1.1.35 SM809 Unwinder failure Circuit voltage too low 107
7.1.1.36 SM810 Unwinder failure Overload 108
7.1.1.37 SM811 Unwinder failure Temperature too high 108
7.1.1.38 SM812 Unwinder failure End of reel 108
7.1.1.39 SM813 Unwinder failure Diameter determination 108
7.1.1.40 SM825 Loop unwinder failure TEACH process 108
7.1.1.41 SM828 Loop unwinder failure Too slow 108
7.1.1.42 SM829 Loop unwinder failure Circuit voltage too low 108
7.1.1.43 SM830 Loop unwinder failure Overload 108
7.1.1.44 SM831 Loop unwinder failure Temperature too high 108
7.1.1.45 SM832 Loop unwinder failure End of reel 108
7.1.1.46 SM845 Winder failure TEACH process 108
7.1.1.47 SM848 Winder failure Torn tape / too slow 108
7.1.1.48 SM849 Winder failure Circuit voltage too low 108
7.1.1.49 SM850 Winder failure Overload 109
7.1.1.50 SM851 Winder failure Temperature too high 109
7.1.1.51 SM865 Loop filler failure 109
7.1.1.52 SM910 Drive failure Low voltage 109
7.1.1.53 SM911 Drive failure High voltage 109
7.1.1.54 SM912 Drive failure High temperature 109
7.1.1.55 SM913 Drive failure Overload (period) 109
7.1.1.56 SM914 Drive failure 109
7.1.1.57 SM917 Drive failure Powerfail 109
7.1.1.58 SM918 Drive failure 109
