Hiboy P7 Manuale utente

The manufacturer reserves the right to make changes to the product,

and update this manual at any time.

www.hiboy.com

USER MANUAL

Electric Bike

Contents

Important! Before Riding, You Should

1. Package Contents

2. Product Overview

3. Installing The Handlebars

4. Installing The Front Wheel

5. Installing The Pedals

6. Installing The Headlight

7. Installing The Saddle

8. Display Introduction

9. How To Use The Display, Headlight & Horn

10. How To Take Off The Battery

11. How To Charge The Battery

12. Notes Of Charging

IMPORTANT! BEFORE RIDING, YOU SHOULD

• Make sure your electric bike is fully charged before the ﬁrst ride

• Make sure the pedals are tight

• Make sure the front wheel is installed properly and tightly

• Check to be sure the tires are inﬂated properly

• Learn how to use the display

• Wear a helmet when riding is highly advised

When riding, please

• Always respect pedestrians

• Obey local trafﬁc rules

• Pay attention to other running vehicles around you

After riding

• If there is any abnormality or loosen parts, please check and repair as soon as possible

• After riding on a rainy day, please clean up the rainwater and sediment immediately

If you have any trouble with the installation, please contact Hiboy customer service

for support: [email protected]

13. Daily Care And Maintenance

14. Speciﬁcations

15. Limited Warranty Statement

16. Q&A and Trouble shooting

17. Contact Us 22

1. Package Contents

Please check package contents carefully, if anything is missing or damaged, please

contact Hiboy customer service for support:support@hiboy.com

Charger x 1

Battery Key x 2

Hexagon wrench x 4

Pedals (R and L) x 2 User manual x 1

Headlight screw x 1

Electric bike x 1

Installing tool x 1

Spring x 2

Skewer x 1

End nut x 1

2. Product Overview

Brake lever

Headlight

Fork

Seat

Freewheel

Rear Derailleur

Crank Set Pedal

Display

Thumb Throttle

Disc Brake

Battery

Disc Brake

Motor

Kickstand

Charge Port

Battery Lock

Sensor

3.Installing The Handlebars

1. Shown in ﬁgure 1, according to the direction of the arrow, rotate the handle stem towards the front of the bike.

2. Put the handlebar in the handlebar mount and be careful with the wires.

3. Insert the screws and tighten alternating sides with installing tool.

4. Verify and check all items are tight.

4. Installing The Front Wheel

Spring

Brake disc

5. Installing The Pedals

1. Insert the front wheel in between the front fork on the bike. Be sure the fork is resting on the outside of the axle.

2. Shown in ﬁgure 2, align the wheel axle with the disc brake slot, put the brake disc into the disc brake slot. Keep

the skewer and spring on the RIGHT side of electric bike's riding direction, and the other spring and the end nut on the LEFT

side of electric bike’s riding direction. Then insert the skewer into the wheel axle, shown in ﬁgure 1. BE AWARE TO DISTINGUISH

THE LEFT SIDE AND THE RIGHT SIDE.

3. Screw the skewer with the end nut and tighten.

4. Lock up the lever. Lift the lever up until parallel with the front fork. The front wheel is now installed.

1. Identify the Left and Right labels on the pedals. They can only be installed in their own side. INCORRECT INSTALLATION WILL

CAUSE DAMAGE. PLEASE BE AWARE TO DISTINGUISH LEFT & RIGHT BEFORE INSTALLATION.

2. L is for the Left pedal of the riding direction; R is for the Right pedal of the riding direction, Screw on the pedal in the direction

of the arrow.

3. Take out the 15 # open-end wrench in the tool kit and tighten it in the direction of the arrow.

Skewer

Spring

End nut

Spring

Skewer End nut

Disc brake slot

Left - Riding direction

Right - Riding direction

6. Installing The Headlight

7. Installing The Saddle

2. Tighten the screw with nut by using the installing tool.

3. Take out the hexagonal wrench and open-end wrench in the tool kit, adjust the headlight to the proper position, and then lock the screws.

1. Shown in Figure 1, insert the screw of the headlight into the headlight hole.

2.Push the saddle down, pull up or push down to adjust the height.

3.Check to make sure the saddle is fully inserted and adjust it accordingly.

1. Install the saddle according to the picture.

4. Lock the handle.

Nut Headlight hole

Headlight Hexagon wrench

Nut

Installing tool

1. Press and hold for 3 seconds to turn on the display. Your bike will be turned on. Press and hold for 3 seconds again to turn

off. The display will turn off automatically when there is no operation or riding for 5 minutes.

2. Short press the "+" or "-" button to change the boost level between 0-5 levels. 0 is the output power, 1 is the minimum boost, 5

is the maximum boost level.

3. Short press to switch the display data of multi-function area when the display is on.

4. When the power is on, press and hold "-" to enter 3.7MPH/H towing mode; release "-" to cancel towing mode.

1110

8. Display Introduction 9. How To Use The Display, Headlight & Horn

1. Press the light button to turn on/off the headlight

2. Press the horn button for horn control

Speed display

Controller failure

Brake

Motor failure

Voltage protection

Battery indicator

Cruise mark

Multi-function display area

Assist level

VOL:voltage ODO:total mileage

TRIP:single meleage

TIME:working time

1312

11. How To Charge The Battery

10. How To Take Off The Battery

1. Insert the key and turn 90 degrees clockwise to open the battery lock of the frame.

2. There is a separate battery lock at the bottom of the frame, which can be opened left or right.

3. Take out the battery upwards from the bottom of the frame.

Your electric bike will be fully charged when the LED light on the charger changes from red (charging) to green (fully charged).

After a period of full charge, it will automatically cut off the charging.

Even so, we still don't recommend to charge your electric bike for a long time.

Do not connect the charger if the charging port is wet. Cover the charging port when not use.

12. Notes of Charging

1. Charging time: 4 hours 80% full charge , full charge in 5-6 hours.

2. The small light on the charger in RED indicates it is in charging; GREEN indicates it is fully charged.

3. Insufﬁcient charging will not inﬂuence the battery lifecycle. AVOIDING deep discharge is helpful to protect the

battery and extend its lifecycle.

4. Pay attention to check whether the surface temperature of the battery case rises too high during charging. It is

FORBIDDEN to cover battery with ﬂammable and explosive materials while charging.

5. Due to high temperature in summer, it is NOT advised to charge it immediately after riding.

FORBIDDEN to charge the battery OUTSIDE where the temperature is below 32-degree F. You are recommended

to charge it in room temperature.

6. If the battery will not be used for a long time, take it off from the bike and discharge its capacity to 60%-80% for

stock. Disconnect it from the charger and place it in a dry, ventilated place without direct sunlight. In order to maintain

a long lifecycle, it is recommended to charge the battery every two months.

13. Daily Care And Maintenance

Cleaning and storage

If you see stains on the electric bike's body, wipe them off with a damp cloth. If the stains won't scrub off, put on some toothpaste, and brush them with a toothbrush,

then wipe them off with a damp cloth. If you see scratches on plastic parts, use sandpaper or other abrasive materials to polish them.

Notes: do not clean the electric bike with alcohol, gasoline, kerosene or other corrosive and volatile chemical solvents to prevent dire damage. Do not wash the

electric bike with a high-pressure water spray. During cleaning, make sure that the electric bike's turned off, the charging cable is unplugged as water leakage may

result in electric shock or other major problems.

When the electric bike's not in use, keep it indoors where it is dry and cool. Do not put it outdoors for long time. Excessive sunlight, overheating and overcooling

accelerate tire aging and compromise the electric bike and the battery pack's lifespan. (Lorsque le electric bike n'est pas utilisé, gardez-le à l'intérieur dans un

endroit sec et frais. Ne le mettez pas en plein air pendant longtemps. La lumière du soleil excessive, la surchauffe et le sur-refroidissement accélèrent le vieillisse-

ment des pneus et compromettent le electric bike et la durée de vie de la batterie.)

WARNING!

Battery maintenance

1. Use original battery packs, use of other models or brands may bring about safety issues;

2. Do not touch the contacts. Do not dismantle or puncture the casing. Keep the contacts away from metal objects to prevent short circuit which may result in battery

damage or even injuries and deaths;

3. Use original power adapter to avoid potential damage or ﬁﬁre;

4. Mishandling of used batteries may do tremendous harm to the environment. To protect natural environment, please follow local regulations to properly dispose used

batteries;

5. After every use, fully charge the battery to prolong its lifespan.

Do not place the battery in an environment where the ambient temperature is higher than 104°F or lower than 14°F (e.g., do not leave the electric bike or the battery

pack in a car under direct sunlight for an extended time). Do not throw the battery pack into ﬁﬁre as it may lead to battery failure, battery overheating, and even another

ﬁﬁre. If the electric bike is expected to be left idle for more than 30 days, please fully charge the battery and place it in a dry and cool place. Keep in mind to recharge

it every 60 days to protect the battery from potential damage which is beyond limited warranty.

Always charge before exhausting the battery to prolong the battery's lifespan. The battery pack performs better at normal temperature, and poor when it is below 32°F.

For instance, when it is below -4°F, the riding range is only half or less at normal state. When the temperature rises, the riding range restores.

The damage caused by prolonged no charge is irreversible and is beyond limited warranty. Once the damage is done, the battery can not be recharged.

15. Limited Warranty Statement

30 DAY SATISFACTION GUARANTEED RETURN POLICY

If you are unsatisﬁed with your purchase, Hiboy's return policy allows you to return your undamaged Hiboy product purchased on the Authorization channel within 30 days counting

from the date of receipt of shipment, and request a refund from the Authorization channel for any reason. Note: The cost of return shipping will be borne by the customer if the

product has no quality issue.

For the return request, Hiboy is not responsible for lost packages due to the carrier, or products received that cannot be veriﬁed. Received products that have damage determined

to have been caused by the end-user may be subject to denial of the return request.

LIMITED PRODUCT WARRANTY

Hiboy product basically will be free from defects in materials and workmanship under normal use for a period aforementioned.

Hiboy does not warrant the operation of the product will be uninterrupted or error-free.

Hiboy is not responsible for damage arising from failure to follow instructions relating to the product's usage.

TO QUALIFY FOR A REFUND, ALL THE FOLLOWING CONDITIONS MUST BE MET:

1. A Return Merchandise Authorization (RMA) must be requested from Hiboy within 30 days from the date of receipt of shipment. To request an RMA, contact Hiboy Service

Team at support@hiboy.com.

2. The cost of return shipping will be borne by the customer.

3. For warranty service, please keep your receipt and/or invoice to validate proof of purchase.

4. Returned product must be in good physical condition (not physically broken or damaged).

5. All accessories originally included with your purchase must be included with your return.

6. If you return a product to Hiboy, (a) without an RMA from Hiboy(b) without all parts included in the original package, Hiboy retains the right to refuse delivery of such return.

1716

14. Speciﬁcations

Dimensions

Size

Tire

Item weight

Max. load

Age

Max Speed

Pure Electric Riding Dist.(Load 143lb)

Pedal Assist Riding Dist.(Load 143lb)

Max Angle of Climb