Hidrotermal Hidro-HX45B Manuale utente

SAUNA HEATER

With Digital Display External Controller

USER MANUAL

1. Sauna heater Specifications

Product Not Including Sauna

Stone

Sauna Room Size Min. Distance to heater

CBM Height A

Min.mm

Min. mm

Model Power Min. Max. cm

Hidro-HX45B 4.5 kw 3 6 110 80 280 100

Hidro-HX60B 6.0 kw 5 9 110 100 280 150

Hidro-HX80B 8.0 kw 8 12 110 130 300 200

Hidro-HX90B 9.0 kw 9 13 110 130 300 200

2. Installation

Install the sauna heater onto the wall with the screw provided in the heater, according to the minimum safety

distances and volumes indicated in table 1 and figure 1, or on the plate of the heater.

1) The heater can be installed in the

wall recess at the minimum height of

1900mm.

2) Do not cover the wall behind the

heater with materials like asbestos or

eternity plates etc., because this sort of

covering protection could cause too

temperature and a risk of burn.

3) Must use qualified materials for the

walls and ceiling.

3. Guard Rails

Please follow the minimum distances requirements in

figure 2 if guardrails are desired around the heater.

4. Digital display Controller

This controller is splash proof. You can install it near the sauna room. Temperature detector must install on

inside room wall. please install according to the diagram to prevent burning the wood wall.

Table 1

Figure 1A

Figure 2

Figure 1B

1. Time

2. Temperature

3. Power-on by alarm

4. Power-off by alarm

5. Light power switch

6. Confirm button of timing

Note:

1. Temperature setting range: 35 ℃~120℃.

2. Once the detedcted temperature exceed the target

temperature, the machine will stop heating.

3. If the detected temperature exceed 120 ℃, the

machine will enter the ultra-high temperature

protection, will not heating. If exceed 140 ℃, the

machine will cut off the power automaticlly, and the

5. Usage of heater operative mode switch and time/temp control

A. Proofread time: Press H to adjust hour. After several blinking, it will confirm automatically.

The same as M to adjust minutes.

B. Power-on by alarm: ( at most 24 hours)

Pressing prepare to place, then pressing H, M button to set time. It will confirm automatically after

several blinking.

C. Power-off by alarm:

Press control time button, the display will blinking and then adjust power-off time (at most 5 hours, at

least 1 minutes). It will confirm automatically after several blinking.

D. After power on, press P button to let temperature work, use +/- button to adjust temperature. Do not

under timing control.

6. Temperature detector

For the recommendation of the

minimum installation distances,

please see installation diagram of

sauna heater for details.

A heater resistant cable of 3 meters

long is provided, which can be

extended to the outside of sauna

room by normal weak current cables.

For cables connection of the

thermostat, please see the following

figure.

7. Installation of temperature detector

8. Limit control

If the temperature is too high inside sauna room like the temperature controller break down, the

temperature limiter in the temperature detector will cut power off and reset automatically after trouble

9. Power connection

A. Connect the phase line to controller power input end L1, L2, L3 respectively. Null

line (neutral line) connect to input end N, protective earth wire attach to 〨.

B. Use the heat resistant conductor to connect the controller power output and with

the heater input end according to the same symbol.

(1) Use screwdriver to remove

the cover at the edge of the

(2) Fix the detector circuit

board upon the sauna heater

(3) Fix the cover on the

detector circuit board.

Front side

Back side

10. Put sauna stone

After installing the sauna heater and controller, put appropriate sauna stone (10~15kg) on heater.

Notice: It's high temperature inside heater, so must use superior sauna stone. The poor heat

resistant sauna stone will crack after heating and watering and damage the sauna heater. Or to

be readily and block the heat circulate then damage the heater.

11.Warning

1. Electrical shock hazard-there are no owner serviceable parts in sauna heater. To avoid electrical

shock hazard, all installations and relevant services shall be performed by qualified personnel.

2. Sauna shall be less than half and hour. Bathing too long may cause heart beating too fast, light

heartache, feeling weak or dizzy. Should the bather stop bathing immediately as soon as the above

symptoms occur.

3. Sauna bath may cause tension to the bather. Thus, one who is one of the followings should be

directed by physician:

A. Being pregnant B. Having heart disease C. Having high blood pressur

D. Having circulation system disease E. After drinking F. After taking medicine

G. Diabetes H. Not feeling well

4. Children must be under the company of adult in taking sauna bath.

5. Risk of scald: Must not touch the sauna heater or trim during heating, as it is hot. Stay at least 30cm

away from the hot heater.

12. Connection draft

A. power input (220V/380V 50Hz)

B. power output

C. light power output

13. Error Code and Corresponding

Error code Reason of error Remark Solution

E0 Alarm on the Circuit board is

damaged

Alarm on the Circuit board is

damaged

Need change the controller circuit

board.

E1 The light in the sauna room

is damaged.

The light in the sauna room

is damaged, no lighting.

Need change the light in the sauna

room.

The heating tube of the

sauna heater machine is

damaged.

The sauna heater machine

will not work.

Need contract with the supplier to

check the machine and change the

heating tube.

E3 Button scan is damaged. There is no reaction when

push the controller button.

Need change the controller circuit

board.

E4 Open circuit in temperature

detector connection.

Open circuit in temperature

detector connection.

Need check the cable connection

of the temperature detector, and

make sure the connection is right.

short circuit in the

temperature detector

connection.

short circuit in the

temperature detector

connection.

Need check the cable connection

of the temperature detector, and

make sure the connection is right.

Temperature detector enter

the ultra-high temperature

protection.

The temperature of the

sauna room is too high.

The sauna heater will stop heating

and cut off the power

automatically, once the detected

temperature lower than 120℃, the

machine can restart work.

E7 Sauna room enter the ultra-

high temperature protection

The temperature of the

sauna room is too high.

The sauna heater will stop heating

and cut off the power

automatically, once the detected

temperature drops to 120℃, the

machine can restart work.

The temperature detection

in the sauna room is

damaged.

The temperature detection

in the sauna room is

damaged.

Need change the temperature

detection.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Hidrotermal Stufa

Hidrotermal

Hidrotermal Hidro-H5.5 Manuale utente

Manuali Stufa popolari di altre marche

oventrop

oventrop Regucor Series Manuale utente

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuale utente

ELMEKO

ELMEKO ML 150 Manuale utente

BN Thermic

BN Thermic 830T Manuale utente

KING

KING K Series Guida

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guida rapida

Well Straler

Well Straler RC-16B Manuale utente

EUROM

EUROM 333299 Manuale utente

Heylo

Heylo K 170 Manuale utente

Eterna

Eterna TR70W Manuale utente

Clarke

Clarke GRH15 Manuale di istruzioni

IRSAP

IRSAP The Radiator Company Ovali Manuale utente

Empire Heating Systems

Empire Heating Systems WCC65 Manuale utente

Wetekom

Wetekom 92 86 43 Manuale utente

Desa

Desa SPC170-F Manuale utente

Watlow

Watlow Watrod Electric Tubular Heaters Manuale utente

Haverland

Haverland ECO-DRY GPS Series Manuale elenco delle parti

Stelpro

Stelpro ASILVC2060 Series Manuale utente