HIK VISION TurboHD Manuale utente

TURBO

HD 1080p Turret & Bullet

Camera

User Manual

UD01984B

User Manual

Thank you for purchasing our product. If there are any

questions, or requests, do not hesitate to contact the

dealer.

This manual applies to models listed below.

Model

DS-2CE56D5T-IR3Z

DS-2CE16D5T-AIR3ZH

DS-2CE16D5T-AIR3Z

This manual may contain several technically incorrect

places or printing errors, and the content is subject to

change without notice. The updates will be added to

the new version of this manual. We will readily improve

or update the products or procedures described in the

manual.

0100001060613

Regulatory Information

FCC Information

FCC compliance: This equipment has been tested and

found to comply with the limits for a digital device,

pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference when the equipment is operated

in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in

which case the user will be required to correct the

interference at his own expense.

FCC Conditions

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received,

including interference that may cause undesired

operation

EU Conformity Statement

This product and - if applicable - the

supplied accessories too are marked with

"CE" and comply therefore with the

applicable harmonized European

standards listed under the EMC Directive 2014/30/EU,

the RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products

marked with this symbol cannot be

disposed of as unsorted municipal waste in

the European Union. For proper recycling,

return this product to your local supplier

upon the purchase of equivalent new equipment, or

dispose of it at designated collection points. For more

information see: www.recyclethis.info.

2006/66/EC (battery directive): This

product contains a battery that cannot be

disposed of as unsorted municipal waste in

the European Union. See the product

documentation for specific battery

information. The battery is marked with

this symbol, which may include lettering to indicate

cadmium (Cd), lead (Pb), or mercury (Hg). For proper

recycling, return the battery to your supplier or to a

designated collection point. For more information see:

www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A)

standards requirements.

Safety Instruction

These instructions are intended to ensure that user can

use the product correctly to avoid danger or property

loss.

The precaution measure is divided into “Warnings” and

“Cautions”

Warnings: Serious injury or death may occur if any of

the warnings are neglected.

Cautions: Injury or equipment damage may occur if any

of the cautions are neglected.

Warnings

In the use of the product, you must be in strict

compliance with the electrical safety regulations of

the nation and region.

Please refer to technical specifications for detailed

information.

Input voltage should meet both the SELV (Safety Extra

Low Voltage) and the Limited Power Source with AC

24V or DC 12V according to the IEC60950-1 standard.

Please refer to technical specifications for detailed

information.

Do not connect several devices to one power adapter

as adapter overload may cause over-heating or a fire

hazard.

Please make sure that the plug is firmly connected to

the power socket.

When the product is mounted on wall or ceiling, the

device shall be firmly fixed.

If smoke, odor or noise rise from the device, turn off

the power at once and unplug the power cable, and

then please contact the service center.

If the product does not work properly, please contact

your dealer or the nearest service center. Never

attempt to disassemble the camera yourself. (We

shall not assume any responsibility for problems

caused by unauthorized repair or maintenance.)

Cautions

Make sure the power supply voltage is correct before

using the camera.

Do not drop the camera or subject it to physical

shock.

Do not touch senor modules with fingers. If cleaning

is necessary, use clean cloth with a bit of ethanol and

wipe it gently. If the camera will not be used for an

Warnings Follow

these safeguards to

prevent serious injury

or death.

Cautions Follow these

precautions to prevent

potential injury or

material damage.

extended period, please replace the lens cap to

protect the sensor from dirt.

Do not aim the camera at the sun or extra bright

places. Blooming or smearing may occur otherwise

(which is not a malfunction), and affect the

endurance of sensor at the same time.

The sensor may be burned out by a laser beam, so

when any laser equipment is in using, make sure that

the surface of sensor will not be exposed to the laser

beam.

Do not place the camera in extremely hot, cold, dusty

or damp locations, and do not expose it to high

electromagnetic radiation.

To avoid heat accumulation, good ventilation is

required for operating environment.

Keep the camera away from liquid while in use.

While in delivery, the camera shall be packed in its

original packing, or packing of the same texture.

Improper use or replacement of the battery may

result in hazard of explosion. Replace with the same

or equivalent type only. Dispose of used batteries

according to the instructions provided by the battery

manufacturer.

IntroductionChapter 1

1.1 Product Features

The camera is applicable for both indoor and outdoor

conditions, and the application scenarios include road,

warehouse, underground parking lot, bar, etc..

The main features are as follows:

High performance CMOS sensor

1080p resolution

OSD menu, Day/Night switch, Smart IR, ACG

IR cut filter

2.8 to 12 mm motorized vari-focal lens

Internal 3-axis adjustment

Built-in heater

Note:

The built-in heater function varies according to different

models.

1.2 Overview of Turret Camera

CVBS

Enclosure

Camera

Clip Plate

Mounting

Base

OSD Button

Switch Cable

Power Cable (12 V DC)

Video Cable (TVI)

Video Cable (CVBS)

Figure 1. 1 Overview of Turret Camera

1.3 Overview of Bullet Camera

Power Cabl (12 V DC)

Video Cable (TVI)

Video Cable (CVBS)

Mounting Base

Main Body

Lens

Figure 1. 2 Overview of Bullet Camera

InstallationChapter 2

Before you start:

Make sure that the device in the package is in good

condition and all the assembly parts are included.

Make sure that all the related equipment is power-off

during the installation.

Check the specification of the products for the

installation environment.

Check whether the power supply is matched with

your power output to avoid damage.

Make sure the wall is strong enough to withstand

three times the weight of the camera and the

mounting bracket.

If the wall is cement, insert expansion bolts before

you install the camera. If the wall is wooden, use

self-tapping screws to secure the camera.

If the product does not function properly, contact

your dealer or the nearest service center. Do not

disassemble the camera for repair or maintenance by

yourself.

2.1 Installation of Turret Camera

Steps:

1. Stick the drill template on the ceiling.

2. Drill the screw holes and cable hole (optional) on

the ceiling according to the supplied drill template.

Note:

Cable hole is required when adopting ceiling outlet to

route the cable.

120°

Screw Hole

Screw Hole Screw Hole

Figure 2. 1 The Drill Template

3. Loosen the screw to remove the clip plate and take

off the main body.

Screw

Clip Plate

Figure 2. 2 Remove the Clip Plate

4. Fix the mounting base to the ceiling with supplied

screws.

Note:

In the supplied screw package, both self-tapping

screws and expansion blots are contained.

If the wall is cement, expansion blots are required

to fix the camera. If the wall is wooden,

self-tapping screws are required.

5. Route the cables through the cable hole and

connect the corresponding cables, such as power

cable and video cable.

6. Install the main body onto the mounting base and

insert the clip plate.

7. Tighten the screw with the wrench.

Clip

Plate

Screw

Figure 2. 3 Install the Turret Camera

8. Power on the camera to check whether the image

on the monitor is gotten from the optimum angle. If

not, adjust the camera according to the figure below

to get an optimum angle.

0° to 360°

0° to 75°

Figure 2. 4 3-Aix Adjustment

2.2 Installation of Bullet Camera

Note:

Both wall mounting and ceiling mounting are suitable

for the bullet camera. Ceiling mounting will be taken as

an example in this section. And you can take steps of

ceiling mounting as a reference when wall mounting is

adopted.

Steps:

1. Stick the drill template on the ceiling.

2. Drill the screw holes and the cable hole (optional) in

the ceiling according to the supplied drill template.

Note:

Cable hole is required when adopting ceiling outlet to

route the cable.

120 °120 °

Screw

Hole

Figure 2. 5 Drill the Template

3. Route the cables to the cable hole and connect the

corresponding cables, such as power cable, and

video cable.

4. Fix the camera to the ceiling with the supplied

screws.

Figure 2. 6 Fix the Camera to the Ceiling

Note:

In the supplied screw package, both self-tapping

screws and expansion blots are contained.

If the wall is cement, expansion blots are required

to fix the camera. If the wall is wooden,

self-tapping screws are required.

5. Power on the camera to check whether the image

on the monitor is gotten from the optimum angle. If

not, adjust the surveillance angle.

1) Loosen the No.1 adjusting screw to adjust the

pan position (0°to 360°).

2) Tighten the No.1 adjusting screw.

3) Loosen the No.2 adjusting screw to adjust the

tilting position (0°to 90°).

4) Tighten the No. 2 adjusting screw.

5) Loosen the No.3 adjusting screw to adjust the

rotation position (0°to 360°).

6) Tighten the No.3 adjusting screw.

0°to 90°

0°to 360°

Figure 2. 7 3-Axis Adjustment

Menu OperationChapter 3

Two methods are available to call the menu. This

section takes method b) as an example to state the

menu operation.

a) Call the menu and adjust the camera parameters

with a coaxial camera controller (purchase

separately).

b) Call the menu with supported TVI DVR by clicking

button on the PTZ interface, or by calling preset No.

95.

Camera

TVI DVR

Monitor

Figure 3. 1 Connection

Steps:

1. After the connection is done, power on the analog

camera, TVI DVR, and the monitor to view the image

on the monitor.

2. Click PTZ Control to enter the PTZ Control Interface.

3. Call the camera menu by clicking button, or call

preset No. 95.

4. Click up/down direction button to select the item,

click Iris + to confirm the selection, and click

left/right direction button to adjust the value of the

selected item.

SMART

FOCUS

SCENE

LENS

INDOOR

SET UP

VIDEO OUT

LANGUAGE

EXPOSURE

BACKLIGHT

DAY & NIGHT

SPECIAL

ADJUST

RESET

EXIT

OUTDOOR

INDOOR1

LOW-LIGHT

MANUAL

SHUTTER

AGC

SENS-UP

BRIGHTNESS

D-WDR

BLC

WDR

ATW

AWC-SET

MANUAL

COLOR

B/W

EXIT

2D NR

3D NR

CAM TITLE

D-EFFECT

MOTION

PRIVACY

DEFECT

SHARPNESS

MONITOR

LSC

HSBLC

OFF

Figure 3. 2 Menu Tree

3.2 VIDEO OUT

PAL: Phase Alternating Lines is a color encoding system

for analog television used in broadcast television

systems in most countries.

NTSC: National Television System Committee is the

analog television system that is used in most of North

America, parts of South America, Myanmar, South

Korea, etc.

3.3 LANGUAGE

Supports multiple languages, as English, Japanese,

Chinese, etc..

3.4 SET UP

3.4.1 SMART FOCUS

Automatically adjusts the camera focus according to the

scene.

You are allowed to set the value manually by clicking

FOCUS+, FOCUS-, ZOOM+, ZOOM-.The value ranges

from 0 to 99. The higher the value, the clearer the

image is.

3.4.2 SCENE

You can select INDOOR, OUTDOOR, INDOOR 1, and

LOW LIGHT as the working environment.

INDOOR: Applicable to the indoor environment whose

color temperature changes are relatively slight.

OUTDOOR: Applicable to the outdoor environment

whose color temperature changes are relatively

obvious.

INDOOR1: Applicable to the indoor environment with

the strong light. Under this circumstance, WDR is ON by

default.

LOW LIGHT: Applicable to the environment with the

low light. Under this circumstance, the slow shutter is

ON by default to receive more light.

3.4.3 LENS

The camera is equipped with 2.8 to 12 mm motorized

vari-focal lens.

3.4.4 EXPOSURE

Exposure describes the brightness-related parameters.

You can adjust the image brightness by the SHUTTER,

AGC, SENS-UP, BRIGHTNESS, and D-WDR in different

light conditions.

EXPOSURE

1. SHUTTER AUTO

2. AGC OFF

3. SENS-UP ---

4. BRIGHTNESS ---|------ 40

5. D-WDR OFF

6. RETURN RET

Figure 3. 3 Exposure

SHUTTER: Shutter denotes the speed of the shutter.

AUTO, 1/25 s, 1/50 s, FLK, 1/200 s, 1/400 s, 1/1k s, 1/2k

s, 1/5k s, 1/10k s, 1/50k s, ×2, ×4, ×6, ×8, ×10, and ×15

are selectable.

Note:

If you select shutter as AUTO or 1/25, the SENS-UP is

adjustable (OFF/AUTO), and the SENS-UP is disabled if

any other shutter speed is selected.

AGC: It’s a form of amplification where the camera will

automatically boost the image output signal to optimize

the clarity of image in poor light conditions. You can set

the AGC value from 0 to 15. The AGC is disabled if the

value is set to 0.

Note:

The noise will be amplified if the AGC is on.

SENS-UP: Sense up increases the exposure on a signal

frame, which makes a camera more sensitive to light so

it can produce images even in low lux conditions. You

can set the SENS-UP as OFF or AUTO according to

different light conditions.

OFF: SENS-UP function is disabled.

AUTO: The SENS-UP function will atomically adjust itself

to x2, x4, x6, x8, x10, x15, x20, x25, and x30 according

to the different light conditions.

Note:

If you select shutter as AUTO or 1/25, the SENS-UP is

adjustable (OFF/AUTO), and the SENS-UP is disabled if

any other shutter speed is selected.

BRIGHTNESS: Brightness refers to the brightness of the

image. You can set the brightness value from 1 to 100

to darken or brighten the image. The higher the value,

the brighter the image is.

D-WDR: The digital wide dynamic range helps the

camera provide clear images even under backlight

circumstances. When there are both very bright and

very dark areas simultaneously in the field of view,

D-WDR balances the brightness level of the whole

image and provide clear images with details.

Set the D-WDR as ON to improve the image quality

under the backlight environment.

Set the D-WDR as OFF to disable the function.

3.4.5 BACKLIGHT

Backlight is applicable for the backlight or the high

luminance environment. You can set the Backlight to

BLC, HSBLC, and WDR.

BLC: (Backlight Compensation): If there’s a strong

backlight, the object in front of the backlight will appear

silhouetted or dark. Based on the back area, BLC

enhances the brightness of the whole image, which

makes it possible to see the area in the strong backlight

clearly, but the backlight area will be over-exposed.

GAIN: The gain of BLC can be set as High, Middle, or

Low, the higher the gain, and the clearer the image is.

Follow the steps below to set a BLC area.

AREA: Click the up/down/left/right button to define the

BLC position and size. Select RET to go back to the BLC

menu or re-define the BLC area.

Default: Restore the BLC settings to the default.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali HIK VISION Telecamera di sicurezza

HIK VISION

HIK VISION DS-2DP1636Z-D Manuale utente

HIK VISION

HIK VISION DS-2CD2132-I Manuale utente

HIK VISION

HIK VISION DS-2TD2667-15/PY Manuale utente

HIK VISION

HIK VISION I092000 Manuale utente

HIK VISION

HIK VISION DS-2CD20x2-I Manuale utente

HIK VISION

HIK VISION DS-2CE5582P(N)-VFIR3 Manuale utente

HIK VISION

HIK VISION DS-2CE16C0T-IRPF Manuale utente

HIK VISION

HIK VISION DS-2DE4425IW-DE Manuale utente

HIK VISION

HIK VISION IR Network Speed Dome Manuale utente

HIK VISION

HIK VISION DS-2CD8464F-EI Manuale utente

HIK VISION

HIK VISION DS-2TD4238-7/S2 Manuale utente

HIK VISION

HIK VISION ECI-B12F Manuale utente

HIK VISION

HIK VISION DS-2CD6425G0 Series Manuale utente

HIK VISION

HIK VISION DS-2XC6225G0-L Manuale utente

HIK VISION

HIK VISION NETWORK CAMERA Manuale utente

HIK VISION

HIK VISION TURBO HD H5T Series Manuale utente

HIK VISION

HIK VISION Turbo HD D0T Series Manuale utente

HIK VISION

HIK VISION DS-2DF8C842IXS-AELW Manuale utente

HIK VISION

HIK VISION TURBO HD U1T Series Manuale utente

HIK VISION

HIK VISION DS-2CC5181P-VF Manuale utente

HIK VISION

HIK VISION TURBO HD F1T Series Manuale utente

HIK VISION

HIK VISION DS-2CE17U8T-IT Manuale utente

HIK VISION

HIK VISION DS-2CE71H0T-PIRL Manuale utente

HIK VISION

HIK VISION DS-2CD7126G0/L-IZS Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente