Hitachi S10 Series Manuale utente
1
Hitachi, Ltd.
S10 Series SIO
Driver
1 System Configuration....................................................................................................... 3
2 Selection of External Device ............................................................................................ 7
3 Example of Communication Setting ................................................................................. 8
4 Setup Items ....................................................................................................................18
5 Cable Diagram ............................................................................................................... 23
6 Supported Device........................................................................................................... 35
7 Device Code and Address Code.................................................................................... 44
8 Error Messages.............................................................................................................. 53
S10 Series SIO Driver
GP-Pro EX Device/PLC Connection Manual 2
Introduction
This manual describes how to connect the Display and the External Device (target PLC).
In this manual, the connection procedure will be described by following the below sections:
1System Configuration
This section shows the types of External
Devices which can be connected and SIO
type.
)"1 System Configuration" (page 3)
2Selection of External Device
Select a model (series) of the External
Device to be connected and connection
method.
)"2 Selection of External Device" (page 7)
3Example of Communication Settings
This section shows setting examples for
communicating between the Display and
the External Device.
)"3 Example of Communication Setting" (page
8)
4Setup Items
This section describes communication
setup items on the Display.
Set communication settings of the Display
with GP-Pro EX or in offline mode.
)"4 Setup Items" (page 18)
5Cable Diagram
This section shows cables and adapters
for connecting the Display and the
External Device.
)"5 Cable Diagram" (page 23)
Operation
S10 Series SIO Driver
GP-Pro EX Device/PLC Connection Manual 3
1 System Configuration
The system configuration in the case when the External Device of Hitachi, Ltd. and the Display are connected is
shown.
Connection Configuration
• 1:1 connection
Series CPU Link I/F SIO Type Setting Example Cable Diagram
S10V LQP510*1
*1 To connect to the Display, a C revision or higher version of the LPU Module is required. Check the alphabet on
the right end of the bar code seal (top surface of the LPU Module) for the revision number of the LPU Module.
UP LINK Connector
on LPU Module
RS422/485
(4wire)
Setting Example 1
(page 8)
Cable Diagram 1
(page 23)
LQE560 (CN1) RS232C Setting Example 2
(page 9)
Cable Diagram 2
(page 29)
LQE560 (CN2) RS232C Setting Example 3
(page 10)
Cable Diagram 2
(page 29)
LQE565 (CN1) RS422/485
(4wire)
Setting Example 4
(page 11)
Cable Diagram 1
(page 23)
LQE565 (CN2) RS422/485
(4wire)
Setting Example 5
(page 12)
Cable Diagram 1
(page 23)
HIDIC-S10α
2α(LWP000) *2 ,
2αE (LWP040) *2,
2αH (LWP070) *2
*2 Connect to the CPU Module's HOST LINK COMPUTER LINK Input/Output Terminal (Upper Calculation I/F).
Terminal Block on
CPU Unit RS422/485
(4wire)
Setting Example 6
(page 13)
Cable Diagram 3
(page 30)
4α, 4αF LWE805
S10mini
Model S (LQP000),
Model H (LQP010),
Model F (LQP011),
Model D (LQP120),
Model L (LQP800)
LQE060 (CN1)
LQE160 (CN1)
LQE560 (CN1)
RS232C Setting Example 7
(page 14)
Cable Diagram 2
(page 29)
LQE060 (CN2)
LQE160 (CN2)
LQE560 (CN2)
RS232C Setting Example 8
(page 15)
LQE165 (CN1)
LQE565 (CN1)
RS422/485
(4wire)
Setting Example 9
(page 16) Cable Diagram 1
(page 23)
LQE165 (CN2)
LQE565 (CN2)
RS422/485
(4wire)
Setting Example
10 (page 17)
Display External Device
S10 Series SIO Driver
GP-Pro EX Device/PLC Connection Manual 4
IPC COM Port
When connecting IPC with an External Device, the COM port used depends on the series and SIO type. Please
refer to the IPC manual for details.
Usable port
Series
Usable Port
RS-232C RS-422/485(4 wire) RS-422/485(2 wire)
PS-2000B COM1*1 , COM2,
COM3*1, COM4
*1 The RI/5V can be switched. Use the IPC’s switch to change if necessary.
--
PS-3450A, PS-3451A,
PS3000-BA, PS3001-BD COM1, COM2*1*2 COM2*1*2 COM2*1*2
PS-3650A (T41 model),
PS-3651A (T41 model) COM1*1 --
PS-3650A (T42 model),
PS-3651A (T42 model) COM1*1*2, COM2 COM1*1*2 COM1*1*2
PS-3700A (Pentium®4-M)
PS-3710A
COM1*1, COM2*1,
COM3*2 , COM4
*2 Set up the SIO type with the DIP Switch. Please set up as follows according to SIO type to be used.
COM3*2 COM3*2
PS-3711A COM1*1, COM2*2 COM2*2 COM2*2
PS4000*3
*3 When making communication between an External Device and COM port on the Expansion slot,
only RS-232C is supported. However, ER (DTR/CTS) control cannot be executed because of the
specification of COM port.
For connection with External Device, use user-created cables and disable Pin Nos. 1, 4, 6 and 9.
Please refer to the IPC manual for details of pin layout.
COM1, COM2 - -
PL3000 COM1*1*2, COM2*1,
COM3, COM4 COM1*1*2 COM1*1*2
PE-4000B Atom N270 COM1, COM2 - -
PE-4000B Atom N2600 COM1, COM2 COM3*4 , COM4*4,
COM5*4, COM6*4
*4 Set up the SIO type with the BIOS. Please refer to the IPC manual for details of BIOS.
COM3*4, COM4*4,
COM5*4, COM6*4
PS5000 (Slim Panel Type
Core i3 Model) *5 *6 COM1, COM2*4 COM2*4 COM2*4
PS5000 (Slim Panel Type
Atom Model)
*5 *6
COM1, COM2*7 COM2*7 COM2*7
PS5000 (Enclosed Panel
Type)*8 COM1 - -
PS5000 (Modular Type
PFXPU/PFXPP)*5 *6
PS5000 (Modular Type
PFXPL2B5-6)
COM1*7 COM1*7 COM1*7
PS5000 (Modular Type
PFXPL2B1-4) COM1, COM2*7 COM2*7 COM2*7
S10 Series SIO Driver
GP-Pro EX Device/PLC Connection Manual 5
DIP Switch settings (PL3000 / PS3000 Series)
RS-232C
*5 When setting up communication between an External Device and the RS-232C/422/485 interface
module, use the IPC (RS-232C) or PS5000 (RS-422/485) cable diagrams. However, when using
PFXZPBMPR42P2 in a RS-422/485 (4-wire) configuration with no flow control, connect 7.RTS+
and 8.CTS+, and connect 6.RTS- and 9.CTS-.
When using RS-422/485 communication with External Devices, you may need to reduce the
transmission speed and increase the TX Wait time.
*6 To use RS-422/485 communication on the RS-232C/422/485 interface module, the DIP Switch
setting is required. Please refer to "Knowledge Base" (FAQs) on the support site. (http://www.pro-
face.com/trans/en/manual/1001.html)
*7 Set up the SIO type with the DIP Switch. Please refer to the IPC manual for details of DIP Switch.
The BOX Atom has not a switch to set the RS-232C, RS-422/485 mode. Use the BIOS for the
setting.
*8 For the connection with the External Device, on the user-created cable read as if the connector on
the Display-side is a M12 A-coding 8 pin socket. The pin assignment is the same as described in
the cable diagram. For the M12 A-coding connector, use PFXZPSCNM122.
DIP Switch Setting Description
1OFF
*1
*1 When using PS-3450A, PS-3451A, PS3000-BA and PS3001-BD, turn ON the set value.
Reserved (always OFF)
2OFF
SIO type: RS-232C
3OFF
4 OFF Output mode of SD (TXD) data: Always output
5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None
6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None
7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Not available
8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Not available
9OFF
RS (RTS) Auto control mode: Disabled
10 OFF
Settings FAQ ID
PFXZPBMPR42P2, RS422/485 change method FA263858
PFXZPBMPR42P2 termination resistor setting FA263974
PFXZPBMPR44P2, RS422/485 change method FA264087
PFXZPBMPR44P2 termination resistor setting FA264088
S10 Series SIO Driver
GP-Pro EX Device/PLC Connection Manual 6
RS-422/485 (4 wire)
RS-422/485 (2 wire)
DIP Switch Setting Description
1 OFF Reserved (always OFF)
2ON
SIO type: RS-422/485
3ON
4 OFF Output mode of SD (TXD) data: Always output
5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None
6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None
7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Not available
8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Not available
9OFF
RS (RTS) Auto control mode: Disabled
10 OFF
DIP Switch Setting Description
1 OFF Reserved (always OFF)
2ON
SIO type: RS-422/485
3ON
4 OFF Output mode of SD (TXD) data: Always output
5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None
6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None
7 ON Short-circuit of SDA (TXA) and RDA (RXA): Available
8 ON Short-circuit of SDB (TXB) and RDB (RXB): Available
9ON
RS (RTS) Auto control mode: Enabled
10 ON
S10 Series SIO Driver
GP-Pro EX Device/PLC Connection Manual 7
2 Selection of External Device
Select the External Device to be connected to the Display.
Setup Items Setup Description
Number of Devices/
PLCs
Enter an integer from 1 to 4 to define the number of Devices/PLCs to connect to the
display.
Manufacturer Select the manufacturer of the External Device to connect. Select "Hitachi, Ltd.".
Series
Select the External Device model (series) and the connection method. Select "S10 Series
SIO".
In System configuration, make sure the External Device you are connecting is supported by
"S10 Series SIO".
)"1 System Configuration" (page 3)
Port Select the Display port to be connected to the External Device.
Use System Area
Check this option to synchronize the system data area of the Display and the device
(memory) of the External Device. When synchronized, you can use the External Device’s
ladder program to switch the display or display the window on the Display.
Cf. GP-Pro EX Reference Manual "LS Area (Direct Access Method Area)"
This feature can also be set in GP-Pro EX or in the Display's offline mode.
Cf. GP-Pro EX Reference Manual "System Settings [Display Unit] - [System
Area] Settings Guide"
Cf. Maintenance/Troubleshooting Guide "Main Unit - System Area Settings"
S10 Series SIO Driver
GP-Pro EX Device/PLC Connection Manual 8
3 Example of Communication Setting
The following shows examples of communication settings of the Display and the External Device, which is
recommended by Pro-face.
3.1 Setting Example 1
Settings of GP-Pro EX
Communication Settings
To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC].
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
.
Settings of External Device
Communication setting of External Device is fixed. No setting is required.
S10 Series SIO Driver
GP-Pro EX Device/PLC Connection Manual 9
3.2 Setting Example 2
Settings of GP-Pro EX
Communication Settings
To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC].
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
Settings of External Device
Communication setting of External Device is fixed. No setting is required.
Rotary switch of External Device needs to be set depending on the channel in use.
Set as shown in the table below.
Channel in use
Rotary Switch
CN1MODU
CN1 8
S10 Series SIO Driver
GP-Pro EX Device/PLC Connection Manual 10
3.3 Setting Example 3
Settings of GP-Pro EX
Communication Settings
To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC].
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
Settings of External Device
Communication setting of External Device is fixed. No setting is required.
Rotary switch of External Device needs to be set depending on the channel in use.
Set as shown in the table below.
Channel in use
Rotary Switch
CN2MODU
CN2 9
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Hitachi Controllori
Hitachi
Hitachi PC-ARF1 Manuale di istruzioni
Hitachi
Hitachi EH-150 Series Istruzioni per l’uso
Hitachi
Hitachi HD64465 Manuale utente
Hitachi
Hitachi PSC-A64S Manuale utente
Hitachi
Hitachi EH-150 Type I Istruzioni per l’uso
Hitachi
Hitachi ATW-YCC-03 Manuale utente
Hitachi
Hitachi EHV+ Series Istruzioni per l’uso
Hitachi
Hitachi FL.NET Manuale utente
Hitachi
Hitachi STARTSP14N001 Manuale utente
Hitachi
Hitachi SJ-P1 Series Manuale utente
Hitachi
Hitachi Eco Compact PC-ARC-A Manuale utente
Hitachi
Hitachi LQZ700 Manuale utente
Hitachi
Hitachi SPX-WDC5 Manuale utente
Hitachi
Hitachi HF-W100E/IoT Manuale utente
Hitachi
Hitachi H8/3637 Manuale utente
Hitachi
Hitachi PC-ARFG2-M Manuale di istruzioni
Hitachi
Hitachi H Series Manuale utente
Hitachi
Hitachi HD44780 Manuale utente
Hitachi
Hitachi MICRO-EHV+ Istruzioni per l’uso
Hitachi
Hitachi HX-CP1S08-0 Manuale utente
