Hitachi CM1473ME Manuale utente

..,.’”-’ ‘“ ;,

COLOUR DISPLAY

OPERATING GUIDE

■POWER SOURCE

This colour display is designed to operate on 220/240 volts 50 Hz, AC. Insert the

power cord plug into a220/240 volts 50 Hz safety grounded outlet.

DO NOT CONNECT THE DISPLAY TO OTHER THAN THE SPECI-

FIED VOLTAGE.

Never remove the back cover of the display as this can expose you to very high

voltage and other hazards. If the display does not operate properly, unplug the

display and call your dealer.

NOTES: 1. This colour display is equipped with athree-wire plug. This plug will

only fit into agrounded power outlet. This is asafety feature, do not

defeat the safety purpose of the grounded plug.

2. If the power cord or plug is damaged or frayed, replace it.

3. Do not overload wall outlets or extension cords as this can result in

fire or electric shock.

WARNING:

TO PREVENT SHOCK OR FIRE HAZARD, DO NOT EXPOSE THIS

DISPLAY TO RAIN OR MOISTURE.

TABLE OF CONTENTS

INTRODUCTION SPECIFICATIONS

Genera l..........,.””...”””” 3Specifications . . . . . . . . . . . . . ...10

Features . . . . -. . . . . .”””””-”” “3 Pin Assignments and

Cautions when using Multi 560 . . . . . 4Signdhvel . . . . . . . . . . . . . . ..ll

HOW TO USE Signal Titing . . . . . . . . . . . . . . . . .12

How to Install the Multi 560 ..., . . . 5How to Remove or Install

Location and Description of aTilt/Swivel Stand . . . . . . . . ...14

User Controls ....”. .””” ”6”””6

Adjusting Multi 560 .“””””-””””. 8

INTRODUCTION

The Multi 560 (CM1473ME) from HITACHI is ahigh resolution colour display monitor

that automatically adjust to horizontal scanning frequencies of graphics boards from

15.5 kHz to 35 kHz and vertical scanning frequencies from 50 Hz to 80 Hz.

The Multi 560 gives IBM Personal System/2, PC, PC/XT PC/AT and Compatibles users

quality graphics and text displays.

■High resolution up to 800 dots x 560 lines from 14-inch large screen.

●The Multi 560 automatically adjust to all horizontal frequencies between 15.5 kHz to

35 kHz and all vertical frequencies between 50 Hz to 80 Hz.

Ergonomically designed cabinet with tilt and swivel base.

The Multi 560 offers both TTL and Analogue inputs.

Selection between TTL and Analogue can be controlled from the front panel.

Cautions when using the Multi 560

WARNINGS

NEVER REMOVE THE BACK COVER

Removal of the back cover shall be done only by qualified personnel.

USE CORRECT VOLTAGE

Use only the rated voltage supply. When the power voltage is extremely high or low, -”

it may cause trouble or it may not give optimum performance.

DO NOT USE AT WRONG PLACE

To prevent shock or tire hazard, DO NOT expose the Multi 560 display to rain or mois-

ture.

This unit is designed to be used in offices or homes. DO NOT subject the unit to vibra-

tions, dust or corrosive gases.

KEEP IN AWELL VENTILATED PLACE

Ventilation holes are provided on the cabinet to prevent the temperature from rising.

DO NOT cover the unit or place anything on top of the unit.

AVOID HEAT

Avoid placing the unit in direct sunshine or near heating appliance.

BE CAREFUL OF MAGNETIC FIELDS

Do not place amagnet, speaker systems, printers or floppy disk drives which generate

magnetism near the unit. Amagnetic field may cause blurred colours or distortion of the

displayed pattern. .-

HOW TO USE

(1) Signal cables are not supplied with this monitor.

(2) Proper signal cables have to be obtained from your dealer to suit your application.

IBM IBM

Signal CGA, Personrd Olivetti

source EGA and System/2 M24

compatibles

Signal cable 9pin-9pin 9pin-15pin 9pin-25pin

SC–09 SC–15 SC–25

(12) Auto/

Manual Select Auto Auto Manual

9pin-+@ IBM PC, PC/XT, PC/AT

with CGA, EGA or

compatible

‘ph-@ 0’vettiM24

5pin+@ IBM Personal System/2

*IBM, IBM Personal System/2 IBM PC, PC/XT and PC/AT are registered trade

marks of International Business Machines Corporation.

Location and Description of User Controls

@POWER SWITCH

Press to turn the power ON. Press again

(❑11111111111111]l[lllllllllllll

mlllltllllllltllllll~ln-

to turn the power OFF.

@POWER ON INDICATOR

Agreen light comes on when the power is ON.

@HORIZONTAL PHASE CONTROL

This control adjust the horizontal position of the display data.

At the extreme sides of control the display data may wrap around depending the signal

timing. Adjust to avoid this.

@BRIGHTNESS CONTROL

While receiving analogue signals, this controls background raster brightness. Adjust the

background to the position where the background is just diminished.

While receiving TTL signals, this controls the brightness level of the whole signal. Adjust

‘-

this to obtain required brightness.

@CONTRAST CONTROL

While receiving analogue signals, this controls the brightness of data (including background

colour). Adjust this to obtain the required brightness.

While receiving TTL signal this controls the brightness differences between low and high

intensity colours (16 colour mode) or between primary and secondary colours (64 colour

mode).

@TEXT SWITCH

Pressing this control switches the screen from full colour to single amber colour while

receiving TTL signal input.

Press it again changes screen back to full colour.

Q!E%$TTL/ANALoGuEs~TcH

By pressing this switch, input signals can be selected between analogue and TTL.

* Avoid supplying both analogue and TTL signals at the same time since this may cause

interferences between the signals (cross-talk). Both connectors can be connected at the

same time.

QHORIZONTAL SIZE CONTROL

This controls the horizontal size.

_VERTICAL SIZE CONTROL

This controls the vertical size.

eVERTICAL CENTERING CONTROL

This controls the vertical position of the data display. /

-16/64 COLOUR SELECT

When pressed in, the 64 colour mode is selected.

When set out, the 16 colour mode is selected.

When the AUTO mode is selected by the switch @.This colour select does not work.

Instead, the monitor select 16 or 64 colour as standard EGA monitor.

@@l?@ AuTo/MANuAL SELECT

When it is pressed out, the auto mode is selected. When the auto mode is selected, the

Multi 560 automatically adjust to the IBM graphics board requirements including Per-

sonal system/2.

When set in, the manual mode is selected.

The display size is proportional to the signal. When the signal timing is differ from afried

size, size controls 8and 9should be adjusted to obtain the required size. These controls

may not be capable for complete controls depending on the signal supplied.

_TTL INPUT TERMINAL

Connect TTL output of the computer.

eANALOGUE ~p~ TE~~AL

Connect analogue output of the computer.

@@@ AC ~LET

Connect asuitable cord set for your power outlet.

Some units are supplied with aproper power cord.

Some are NOT.

@TILT& SWIVEL BASE

Refer to page 14.

When signals other than the recommended signal are received

Cause

Phenomenon

Adjustment

Picture width too

wide. Data display period is more than standard timing.

DAdjust horizontal size control @) .

Picture width too

narrow. Data display period is less than standard timing.

BAdjust horizontal size control @.

Picture deviates to

the right. Horizontal front porch is greater than standard timing.

uAdjust horizontal phase control @.

Picture deviates to

the left. Horizontal front porch is less than standard timing.

mAdjust horizontal phase control @.

Height of picture too

short. Vertical blanking period is more than standard timing.

aAdjust vertical size control @.

‘.

.,- f

Cause

Phenomenon Adjustment

Picture length

too much extended. Vertical blanking period is less than standard timing.

[m]

.: .. Adjust verticil sizecontrol @) .

,:.

. . .. .

Picture deviates

upward. Vertical front porch is less than standard timing.

,,. ,..

:J: ,’

J-.,.-,

Adjust vertical centering control @.

Picture deviates

downward. Vertical front porch is greater than standard timing.

[=1

,,s“L..,,.S,alt.,u>$::.

“~;~::;,~;~:33},f$~,1~,z,,

.- .,,~, .,

Adjust vertical centering control @.

..,.

Note: Adjustment range has its design limit which may not cover the timing you would

-1

/a like to see on the display.

SPECIFICATIONS

‘====)

CRT 14”, 90-deg., In-Line, 0.31 mm dot pitch P22,

Tinted glass (55%), Non-Glare (Silica)

Analogue TTL

0.6Vp-p/75-ohm positive TTL level positive

Input Signal Video R, G, BR, G, B, I(16-colour) or

R, r, G, g, B,b

(64-colour)

H/V composite or

sync H, Vseparate TTL

TTL

Scanning frequency Horizontal :15.5 -35kHz

Vertical :15-80 Hz

Resolution Horizontal :800 dots

Vertical :560 lines

Video bandwidth 30 MHz

Display size 240 (H) x 180 (V) mm

Linearity +/– 10%

Misconvergence Center :0.4 mm Max.

Corners :0.6 mm Max.

Power input AC 220/240 V, 50 Hz

Connector 9-pin DB-9 for TTL and analogue

Power consumption 80W

Dimensions (W xHxD) 358 x 362 x 389mm

Weight 14kg

Specifications are subject to change without notice.

Questo manuale è adatto per i seguenti modelli

Altri manuali Hitachi Monitor

Hitachi

Hitachi 55PD8800 Manuale utente

Hitachi

Hitachi CM715U Manuale utente

Hitachi

Hitachi CML156XW Manuale utente

Hitachi

Hitachi DT3140 Manuale utente

Hitachi

Hitachi CMP4201 Manuale utente

Hitachi

Hitachi CM721F - 19" CRT Display Manuale utente

Hitachi

Hitachi CMP4211 - 42" Plasma Panel Manuale utente

Hitachi

Hitachi UT32-MH700A Manuale utente

Hitachi

Hitachi DW1-UA Manuale utente

Hitachi

Hitachi CM776ET Manuale utente

Hitachi

Hitachi CM721FET Manuale utente

Hitachi

Hitachi CML154XW Manuale utente

Hitachi

Hitachi CML171SXW Manuale utente

Hitachi

Hitachi 42PD8900TA Manuale utente

Hitachi

Hitachi StarBoard T-17SXL Manuale utente

Hitachi

Hitachi COLOR PLASMA TELEVISION 42PD9800TA Manuale utente

Hitachi

Hitachi CML156XW Manuale utente

Hitachi

Hitachi 32HDL51M Manuale utente

Hitachi

Hitachi 42PMA225EZ Manuale utente

Hitachi

Hitachi CM2186A Manuale utente

Hitachi

Hitachi V700 Manuale utente

Hitachi

Hitachi CM827U Manuale utente

Hitachi

Hitachi CM802ET Manuale utente

Hitachi

Hitachi CML174SXWB Manuale utente

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione