Hitachi CP-TW2503 Manuale utente

FT-01 Finger Touch Unit - Quick Start Guide

INSTALLATION:

• Use one of three ways to attach/secure the

ﬁnger touch unit:

— Use four strips of double sided tape (A) on

ﬂat, smooth surfaces

— Using magnetic sheet (B), afﬁx three strips.

Secure on a ﬁxed location i.e. metal

— Using two screws (C)

*Always use screws when installing at heights

of more than 6.5’ or 2m

• Use a Phillips-head screwdriver to remove the

cover

• Use the USB cable to connect the Finger

Touch to the Projector option port

CONFIGURATION:

1. Press the IWB button on the remote control to change to

WITH PC mode.

The unit must be mounted 2"- 4" above the

projected image, also allow 2" between the

projected image and the screen frame. You may

need to shrink your image. The image needs to be

between 60"- 80" diagonal.

The adjustment procedure using a Windows PC

is shown. If using a Mac PC, perform the same

procedure by referring to the U-Pointer manual

loaded in the DVD drive.

Models CP-TW2503 and CP-TW3003

Getting Started: Installation and Conﬁguration

Please read pages 12-16 in the FT-01 User’s Manual for complete installation instructions

U-Pointer software should be installed on computer before Finger Touch Unit is used

This device can only be used with Hitachi LCD projectors. It cannot be used with

other projectors or for ﬂoor-mounted installation.

Double-sided tape (A)

Pull out so that

3M is visible.

Red side

Magnetic sheet (B) Fixing screws (C)

or or

Projector's Ports

USB cable

Option port

2 Click the U-Pointer icon in the task tray of the

computer and select conﬁguration

U-POINTER CONFIGURATION:

1. Set U-Pointer conﬁguration as shown below

2. Once the conﬁrmation screen is displayed,

click [Finish]

Getting Started: Installation and Conﬁguration (continued)

3. Click [Next] [Alignment View] to open the

Alignment View.

4. Secure the supplied adjusting bars to the right

and left edges of the projector display screen.

Align the white print surface of the adjusting bar

toward the direction of the ﬁnger touch unit and

use the double sided tape to secure

Adjusting bar

approx. 8mm

5. Turn the adjusting knob 2until the reﬂection line

appears on the screen.

6. Turn the adjusting knob 3clockwise until the

reﬂection line is horizontal.

7. Turn the adjusting knob 1clockwise so the

reﬂection line moves near the vertical center.

8. If the reﬂection line is not horizontal, use the

adjusting knobs 2or 3to make the reﬂection

line horizontal

9. Turn the adjusting knob 1counterclockwise

until two adjusting bars each appear at the

bottom right and left of the screen. You are

looking for two white dots on either side.

Touch your ﬁnger on the projector display and check that your ﬁngertip is lit up within

the display

Conﬁguration continued on next page

• Attach the cover so that it does not touch the adjusting knobs

• Remove adjusting knobs

• Click [OK] to exit the alignment view

• Click [Next] [Auto Calibration] to run Auto Calibration

• Click [Finish] to exit U-Pointer Conﬁguration

• Click the U-Pointer icon on the task tray, select [Finger Touch Mode]

This completes the adjustment

GLOSSARY:

IWB - Interactive white board. Use with I-PEN or ﬁnger touch unit to make drawings on your own or

projected images.

I-PEN - The interactive pen that is provided with the projector.

Stand Alone Mode – With this mode, you can use the projector as an interactive whiteboard by itself.

With PC - With this mode, you can connect the projector and PC and use advanced drawing, annotation,

media features and organize ﬁles.

Calibration (Calibrate) - Process needed so that the projector can recognize the I-PEN or Finger

Touch Unit.

U-Pointer - U-Pointer is the “interactive projector driver” for PC or MAC®. It also has an auto

calibration feature.

i-PRO - Advanced annotation, drawing & multi-media interactive software. For use WITH PC mode.

StarBoard Software - Advanced Interactive software that comes complimentary with your Hitachi

projector. There is no yearly subscription fee associated with the use of this software.

BASIC FINGER TOUCH OPERATIONS:

Left Click - Touching the screen with your ﬁnger performs a clicking operation

Double Click - Two quick clicks results in a double click operation

Right Click - Touch and hold for 2 seconds to perform a right click command

Drag - Moving your ﬁnger while touching the screen performs a dragging operation

There is no yearly subscription fee for the StarBoard Interactive Software,

it comes complimentary with Hitachi Interactive Projectors

If you have been using other interactive software and want to transfer ﬁles to use with StarBoard, you can!

1. Open your current ﬁle

2. Go to the File tab and select Save As

3. Save your ﬁles as .IWB

4. Load back into StarBoard as .IWB ﬁle

To begin, click the U-Pointer icon on the task tray

of your computer and select Finger Touch Mode

You can now use your ﬁnger to control operations

in the same way as if using the I-PEN or mouse.

You can switch between using the I-PEN

and ﬁnger touch, but they can not be used

simultaneously.

How to transfer ﬁles to StarBoard

Using the Finger Touch Unit

Getting Started: Installation and Conﬁguration (continued)

For complete information and installation instructions refer to the

FT-01 User’s Manual or go to www.hitachiserviceusa.com

We are here to help! 800-HITACHI was established to give our U.S.

customers easier access to Hitachi products and service information.

Hitachi’s Call Center is empowered to provide you with expedited service

& solutions. Our goal is to ensure you have smooth performance from

any of our Hitachi Business Products. Some examples of our service

include:

• Out of the box missing accessories

• In-warranty lamp replacement

• Hook-up and operational assistance

• Wireless, networking and support of RS-232 codes

• Coordinating a service solution for any service related issue

Call: 800-HITACHI (800-448-2244)

Email: lcdprojector@hal.hitachi.com

Hours of operation: Monday through Friday, 9:00 AM—6:00 PM EST

Trouble Shooting

HI0392-04/15

Q. Where do I get the U-Pointer Software?

A. U-Pointer software comes complimentary with your Hitachi interactive

projector. It is also available for download under the interactive projectors

resources tab on the Hitachi Projectors website:

http://dmd.hitachi-america.us/products/consumer/digitalmedia/lcd_

projectors/lineup/details/CP-TW2503.php

Q. Can I mount the ﬁnger touch unit above my white board?

A. No. The ﬁnger touch unit MUST be mounted on the same surface as the

display.

Q. Can I use the ﬁnger touch unit on an uneven surface?

A. No. The surface must be ﬂat, there is only a 2mm tolerance.

Q. Can I use this in “stand alone mode”?

A. No. A PC is required in order for you to interact with this unit. Also make

sure the projector’s IWB mode is set to “with PC mode” in the OSD menu of

projector, and set to “Finger touch mode” at the U-pointer’s menu on the PC.

Q. When using the ﬁnger touch unit, the cursor and drawing

functions are inaccurate (i.e. The line I am drawing is 2 inches away

from tip of the interactive pen.)

A. This may caused by some factors. It may be out of calibration, run auto

or manual calibration and retry. Or an uneven surface, surface with curve

will cause inaccuracy. Also inaccurate alignment of FT-01 will also cause the

inaccuracy. Please refer to the manual for appropriate settings.

Q. Will the chalk shelf on my whiteboard interfere with my ﬁnger

touch interaction?

A. Sometimes Yes. The reﬂection from the chalk shelf sometimes interferes.

There are “Antireﬂection bars” included with the ﬁnger unit for this reason.

Q. How do I get a full image and full screen interaction on my white

board when using the ﬁnger touch unit?

A. You cannot. The ﬁnger touch unit MUST be mounted 2-4 inches above the

image, and it also requires 2 inches between the frame, if there is frame. This

means you have to shrink the image to provide this requirement.

FT-01 Finger Touch Unit - Quick Start Guide

Models CP-TW2503 and CP-TW3003

Altri manuali per CP-TW2503

Questo manuale è adatto per i seguenti modelli

Altri manuali Hitachi Pannello touch

Hitachi

Hitachi Compute Blade 500 Series Manuale utente

Manuali Pannello touch popolari di altre marche

FlowLine

FlowLine Data loop Manuale utente

ALPEX

ALPEX AEx-8 P Series Manuale utente

Ltech

Ltech E5S Manuale utente

Harman

Harman AMX MODERO S MSD-701-L2 Manuale utente

Acnodes

Acnodes PC 1150 Manuale utente

AIS

AIS IP10IA99 series Manuale utente

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manuale utente

YASKAWA

YASKAWA TP 610C Manuale utente

B&R

B&R Power Panel C Series Manuale utente

Beijer Electronics

Beijer Electronics X2 control Manuale utente

AXIOMTEK

AXIOMTEK GOT321W-521 Manuale utente

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manuale utente

Qomo

Qomo QIT1386 Manuale utente

DFI

DFI KS104-CD Manuale utente

AMX

AMX AXP-PPC Guida

Sartorius

Sartorius X3 PR 5410 Manuale utente

AMX

AMX Modero X Series Manuale utente

Advantech

Advantech TPC-30 Series Manuale utente