HM Machinery HM SBM-32F Manuale utente

MANUAL

GEARED HEAD DRILLING MACHINE

HM SBM-32F

READ THIS MANUAL BEFORE USE

DECALAIRATION OF CONFORMITY

We hereby declare that the concept and manufacturing of the machine mentioned below

meets all safety and health prescriptions according mentioned below EU regulations. In case

of technical modifications without permission this declaration is void.

MANUFACTURER:

HM Machinery

Industrivej 3-9

9460 Brovst

DENMARK

Tlf.: + 45 98 23 60 88

DESCRIPTION & IDENTIFICATION OF THE MACHINE:

06320005 HM SBM-32F AUT

EC DECLARATION OF CONFORMITY:

Low Voltage regulation – European Parliament and Council directive 2014/35 / EU of 26

February 2014

EMC - European Parliament and Council directive 2014/30 / EU of 26 February 2014

RESPONSIBLE FOR THIS TECHNICAL DOCUMENTATION:

Brovst 2018

Managing Director

Claus Nielsen

Vigtigt

Husk påfyldning af højtryks gearolie EP ISO VG 150 inden opstart.

Skal fyldes op til halvdelen af skueglasset er fyldt !

Important

Remember to fill oil the gearbox with high pressure gear oil EP ISO VG 150 before

use of the machine. Fill up to till half of the sight glass is covered !

Achtung

Bitte mit Hochdruck-Getriebeöl EP ISO VG 150 auffüllen bevor die Maschine

gestartet wird. Bitte Öl füllen bis das Schauglas halb gefüllt ist!

Important

S'il vous plaît n'oubliez pas de mettre de l'huile dans

la boîte de vitesses avant d'utiliser la machine. Remplissez jusqu'à ce que la moitié

du voyant soit recouverte!

ENGLISH

1. LIMITED WARRANTY..........................................................................................................7

2. SAFETY AND GENERAL INFORMATION..............................................................................7

3. TEST REPORT..................................................................................................................12

4. MAIN SPECIFICATIONS ....................................................................................................13

5. INSPECTION ....................................................................................................................15

6. WIRING DIAGRAM............................................................................................................. 17

7. ELECTRICAL COMPONENTS LIST....................................................................................18

8. WARRANTY .....................................................................................................................31

DANSK

1. BEGRÆNSET GARANTI....................................................................................................35

2. SIKKERHED OG GENERELLE OPLYSNINGER ...................................................................35

3. BEREGNET BRUG AF MASKINEN .....................................................................................37

4. TESTRAPPORT ............................................................................................................... 40

5. EFTERSYN...................................................................................................................... 43

6. FUNDAMENTDIAGRAM.................................................................................................... 43

7. LEDNINGSDIAGRAM........................................................................................................ 45

8. LISTE OVER ELEKTRISKE KOMPONENTER..................................................................... 46

9. GARANTI......................................................................................................................... 50

GERMAN

1. BESCHRÄNKTE GARANTIE ............................................................................................. 54

2. SICHERHEIT UND ALLGEMEINE INFORMATIONEN ..........................................................55

3. TESTBERICHT ................................................................................................................ 60

4. HAUPTSPEZIFIKATIONEN................................................................................................61

5. INSPEKTION ................................................................................................................... 63

6. SCHALTPLAN ..................................................................................................................65

7. LISTE DER ELEKTRISCHEN KOMPONENTEN...................................................................66

8. GARANTIE....................................................................................................................... 70

NOTE

This manual has been prepared for the owner and operators of this

machine. Its purpose, aside from machine operation, is to promote safety

through the use of accepted correct operation and maintenance procedures.

Completely read the safety and maintenance instructions before operation

or servicing the machine. To obtain maximum life and efficiency from your

machine, and to aid in using the machine safety, read this manual.

Since we continually strive to incorporate latest developments in the

construction of the machine, it is quite possible at time, due to printing and

shipping requirements, some dat

a may not correspond to the machine in

question。

1. LIMITED WARRANTY

We make every effort to assure that our products meet high quality and durability

standards and warrants to the original retail consumer/purchaser of our products that

each product be free from defects in materials and workmanship as follow: ONE YEAR

LIMITED WARRANTY ON ALL PRODUCTS UNLESS SPECIFIED OTHERWISE. This

warranty does not apply to defects due directly or indirectly to misuse, abuse,

negligence or accidents, normal wear and tear or alterations outside our facilities, or

to a lack of maintenance.

We shall in no event be liable for death, injuries to persons of for incidental,

contingent, special, or consequential damages arising from the use of our products.

To take advantage of this warranty, the product or part must be returned to us for

examination, postage prepaid. Proof of purchase date and an explanation of the

complaint must accompany the merchandise. If our inspection discloses a defect, we

will either replace the product, or refund the purchases price if we cannot readily and

quickly provide a repair or replacement, if you are willing to accept a refund. We will

return repaired product or replacement at our expense, but if it is determined there is

no defect, or that the defect resulted from causes not within the scope of our

warranty, then the user must bear the cost of storing and returning the product.

2. SAFETY AND GENERAL INFORMATION

SAFETY

A drilling machine, due to its purpose, is considered an “open machine” Therefore,

some safety measures must be taken to avoid accidents.

Bear in mind the following safety instructions:

The machine must always be operated for the purpose for which it was designed.

Do not ever stand under a hanging machine or nearby, when it is being loaded for

transportation.

Connect the machine to an exclusive electric connection, which includes

differential switch of protection. Plug in first the green-yellow protection wire and

then the others.

The piece must always be fastened with suitable devices. Do not ever handhold

the pieces.

Sharpened tools in good condition must always be used.

Appropriate tools must always be used, Do not ever adapt a tool for a use, for

which it was not designed.

Use the correct speeds and feeds for the material being machined as well as for

the tool being used.

Use glasses to prevent small chips from getting in the eyes.

Insert the tools correctly in the tool holder cone.

Fix the piece fastening devices to the machine table.

Do not wear baggy clothes, loose gloves, etc, which can be caught by the tool

while drilling.

Keep the working place clean.

Gather the chips with suitable instruments (brush, gloves, etc.)

Before carrying out any operation which is not strictly drilling, tapping etc. (like

lubricating, changing of tools, etc,) turn the main switch to the “0”position.

Before changing speeds, stop the machine and wait until all moving elements are

completely brought to a halt.

Do not ever leave the machine on without supervision. When leaving the machine,

check that the general switch is in the “0”position and that moving elements are

stopped.

Check periodically the correct operating of all security controls and elements of

the machine.

Before pressing the starting pushbutton, set the drill protector guard in the

working position.

Consider work area environment. Don’t use electric power driven tools in damp or

wet locations. Keep work area well lit. Don’t use electric power tools in presence

of flammable liquids or gases.

Keep children away.

Use only such accessories and attachments as are recommended in the operating

instructions or the catalogue for the power tool concerned.

FORESEEN USE OF THE MACHINE

The drilling machine was designed to be used with specific tools and for certain

machining operations.

The most common machining operation is the drilling of holes with helicoidal drills.

The drilling of holes is carried out by the combination of a drill turning movement and

a feed movement in the turning spindle direction.

Besides the helicoidal drill, other tools can be used to drill holes. There is a great

variety of drill types and shapes in the market which can be used on this machine,

provided that they are designed for such a purpose and that they can be fixed in the

spindle taper. They will usually be the Morse taper or ISO type. The drill shanks should

have the corresponding taper to the spindle in which they are to be fitted, or parallel

shank if they are going to be fitted by means of a tool holder. Contact the tool

manufacturer for any further information. Do not ever use tools which were not

designed to be used in a drilling machine and that have been adapted.

A drilling machine can also perform other machining operations apart from the

drilling, such as tapping, reaming, chamfering, punch marking, countersinking, spot

facing, to perform such operations, it is necessary to have appropriate tools, specially

designed for these sorts of jobs. In the tapping case, besides using correct tool, the

machine has to be provided with such a device that verses the turning direction of the

tool when it reaches the depth previously fixed.

CORRECT USE OF THE MACHINE

Not exceeding its working capacity.

Operating the machine by qualified and trained staff and according to the points

mentioned in the instruction book.

Working under the safety systems provided with the machine, checking them and

keeping them.

Watching the safety measures mentioned in the instruction book and notices on

the machine.

Wearing clothes which provide personal safety as mentioned in the instruction

book.

Watching the safety measures which may affect work on the machine and that

can be lawfully expected, as well as those demanded in the workshops.

PIECE CLAMPING.

Tangential cutting forces and axial forces in the feed direction of the tool are mainly

produced during the drilling process. The tangential forces produce a moment of

forces which will make the piece being drilled to turn. Therefore, the pieces to be

drilled (or to be machined by one of the operations mentioned above) must be

clamped in an appropriate device such as a drill chuck and the drill chuck must be

correctly clamped to the machine table. For this reason the machine tables are

provided with “T” slots.

The pieces must be clamped conveniently by some clamping device.

The clamping devices in turn must be clamped to the machine table.

The machine table is provided with “T” slots for such purpose.

TOOL FIXING

The tools generally used in this machine will have parallel or taper shanks. Drill holders

are normally used to fix the parallel shank tools to the main spindle of the machine.

This fixing device is used for small drill diameters (max. up to dia.16mm). Bigger

diameter drills, usually have taper shank of Morse taper (the ones of smaller diameters

than 16mm can have taper shanks).

The housing in the main spindle can insert the tools of Morse taper type. It is very

important to insert the tool taper correctly in the main spindle taper to avoid the tool

falling from its housing when turning and provoke an accident. The coupling system

itself of the tool male taper in the female taper of the main spindle is auto-locking, but

for it to do so the surfaces of the tool taper and spindle taper must be in contact. To

get the best possible contact, the surfaces of the tool taper as well as the spindle

taper should be in good conditions. Therefore, it is advisable to handle the tool as well

as the spindle of the machine carefully.

CHIPS DURING MACHINE

The machining process removes material from the piece. This material is released in

chips, which can be of different shapes depending on the material itself. The most

common ones are of three types: fragmented chips in small bits, short helicoidal

Indice

Lingue:

Altri manuali HM Machinery Trapano

HM Machinery

HM Machinery SBM 28B Manuale utente

Manuali Trapano popolari di altre marche

Makita

Makita BDF456 Manuale utente

Black & Decker

Black & Decker LDX220 Manuale utente

Hitachi

Hitachi DH 40MA Manuale utente

Challenge

Challenge JO Manuale tecnico di riferimento

Makita

Makita LXFD01 Manuale utente

Festool

Festool T18+3 Manuale utente

Milwaukee

Milwaukee M12 FPDX-202X Manuale utente

EINHELL

EINHELL TE-RH 32 E Manuale utente

Makita

Makita DHP484 Manuale utente

Makita

Makita FD05 Manuale utente

Bosch

Bosch PSB 530 RA Manuale utente

Maximum

Maximum 054-1359-4 Manuale utente

Makita

Makita HP332D Manuale utente

Raider

Raider RDP-HD31H Manuale utente

Bort

Bort BPM-1400x2 Manuale utente

Black & Decker

Black & Decker 7266 Manuale utente

KENT USA

KENT USA TRD1230 Manuale utente

Bosch

Bosch GSB 19-2 RE Manuale utente