HMS Anybus Wireless Bolt Serial Manuale utente
司騰達股份有限公司
HMS 台灣總代理 – Remote Access 跨國遠端連線與自動化工業的最佳選擇
司騰達公司致力於推廣數位化工廠和 IIoT 工業物聯網的解決方案，並與歐洲最先進的公司 – HMS 集團
合作，同時透過引進更多歐美的技術能量，提供客戶關於工業 4.0 的顧問諮詢服務，並將教育與産業連結，
協助台灣産業逐步完成從現場設備、生産資訊、通訊 IoT 的垂直整合，並整合 M2M 工業總線與軟體開發，
從而實現數位化工廠與自動化機械領域的創新。
司騰達聯絡訊息
臺北客服專線：(02)-2242-1625
台中客服專線：(04)-2451-0611
客服信箱：[email protected]
Line ID：bhp.tw
www.bhp.com.tw
Anybus®Wireless Bolt™
INSTALLATION GUIDE
SCM-1202-006/SP2139 1.7 ENGLISH
Important User Information
Liability
Every care has been taken in the preparation of this document. Please inform HMS Industrial Net-
works AB of any inaccuracies or omissions. The data and illustrations found in this document are
not binding. We, HMS Industrial Networks AB, reserve the right to modify our products in line with
our policy of continuous product development. The information in this document is subject to
change without notice and should not be considered as a commitment by HMS Industrial Networks
AB. HMS Industrial Networks AB assumes no responsibility for any errors that may appear in this
document.
There are many applications of this product. Those responsible for the use of this device must en-
sure that all the necessary steps have been taken to verify that the applications meet all perform-
ance and safety requirements including any applicable laws, regulations, codes, and standards.
HMS Industrial Networks AB will under no circumstances assume liability or responsibility for any
problems that may arise as a result from the use of undocumented features, timing, or functional
side effects found outside the documented scope of this product. The effects caused by any direct
or indirect use of such aspects of the product are undefined, and may include e.g. compatibility is-
sues and stability issues.
The examples and illustrations in this document are included solely for illustrative purposes. Be-
cause of the many variables and requirements associated with any particular implementation,
HMS Industrial Networks AB cannot assume responsibility for actual use based on these exam-
ples and illustrations.
Intellectual Property Rights
HMS Industrial Networks AB has intellectual property rights relating to technology embodied in the
product described in this document. These intellectual property rights may include patents and
pending patent applications in the USA and other countries.
Trademarks
Anybus®is a registered trademark and Wireless Bolt™is a trademark of HMS Industrial Networks
AB. All other trademarks are the property of their respective holders.
Anybus®Wireless Bolt™Installation Guide SCM-1202-006/SP2139 1.7
Description 3 (16)
1 Description
This document describes how to install Anybus Wireless Bolt and set up a basic
configuration. For additional documentation and technical support, please visit
the Anybus support website www.anybus.com/support.
Anybus Wireless Bolt provides wireless communication capability over WLAN
and/or Bluetooth®to Ethernet, serial and CAN networks.
Bluetooth and WLAN (2.4 GHz) can be used simultaneously. Ethernet can be
used at the same time as either the serial interface or the CAN interface.
Typical applications for Anybus Wireless Bolt include:
• Adding wireless cloud connectivity to industrial devices
• Accessing devices from a laptop, smartphone or tablet
• Ethernet cable replacement between devices
Limitations
• Bluetooth PAN (Personal Area Network) cannot be used with iOS devices.
• Bluetooth PAN may not be compatible with some Android devices due to
varying implementations of Bluetooth by different manufacturers.
• WLAN 5 GHz cannot be used at the same time as WLAN 2.4 GHz or
Bluetooth.
Trademark Information
Anybus®is a registered trademark and Wireless Bolt™is a trademark of HMS In-
dustrial Networks AB. All other trademarks mentioned in this document are the
property of their respective holders.
Anybus®Wireless Bolt™Installation Guide SCM-1202-006/SP2139 1.7
Installation 4 (16)
2 Installation
Anybus Wireless Bolt should be mounted vertically (logo facing upwards) for best
performance due to the characteristics of the internal antenna.
For optimal reception, wireless devices should be placed with a line of sight be-
tween them clear of obstructions. A minimum distance of 50 cm between the de-
vices should be observed to avoid interference.
Make sure that you have all the necessary information about the capabilities and
restrictions of your local network before installing Anybus Wireless Bolt. Contact
your network administrator if in doubt.
Caution
This equipment emits RF energy in the ISM (Industrial, Scientific,
Medical) band. Make sure that all medical devices used in proximity to
this device meet appropriate susceptibility specifications for this type of
RF energy.
This product contains parts that can be damaged by electrostatic
discharge (ESD). Use ESD protective measures to avoid equipment
damage.
Anybus®Wireless Bolt™Installation Guide SCM-1202-006/SP2139 1.7
Installation 5 (16)
Mechanical Installation
Anybus Wireless Bolt is intended to be mounted on top of a machine or cabinet
through an M50 (50.5 mm) hole using the included sealing ring and nut.
Tightening torque: 5 Nm ±10 %
Make sure that the sealing ring is correctly placed in the circular groove
in the top part of the housing before tightening the nut.
All measurements are in mm.
Anybus®Wireless Bolt™Installation Guide SCM-1202-006/SP2139 1.7
Installation 6 (16)
Connector Pinning
Note the location of the RESET button when the connector is attached to the
Wireless Bolt. Pin 1 will be the pin closest to the button.
Pin Name Description
1 VIN Power 9–30 VDC
2 GND Power Ground
3 DI Digital input (9–30 VDC)
4DI_GND Digital input ground
5ETN_RD+ Ethernet receive + (white/orange)
6ETN_RD- Ethernet receive - (orange)
7ETN_TD- Ethernet transmit - (green)
8ETN_TD+ Ethernet transmit + (white/green)
9RS485_B RS-485 B Line
10 FE/Shield Ethernet:
Serial:
Functional Earth
Functional Earth and Shield
11 RS232_TXD RS-232 Transmit
12 RS485_A/RS232_RXD RS-485 A Line / RS-232 Receive
13 RS232_RTS RS-232 Request To Send
14 RS232_CTS RS-232 Clear To Send
15 ISO_5V Isolated 5 V for serial interface
16 ISO_GND Isolated Ground for serial interface
17 CAN_L CAN Low
18 CAN_H CAN High
• If using a shielded Ethernet cable the shield must be unconnected.
• RS-232 and RS-485 cannot be used at the same time.
• Use termination for RS-485 and CAN when required.
Anybus®Wireless Bolt™Installation Guide SCM-1202-006/SP2139 1.7
Installation 7 (16)
Cabling
To make an Ethernet connector cable for the Anybus Wireless Bolt:
1. Cut off one of the connectors on a standard Cat5e or Cat6 Ethernet cable.
2. Strip off about 40 mm (1½ inch) of the cable jacket and untwist the orange,
orange/white, green and green/white wires. The other wires will not be used.
3. Strip off about 7 mm (¼ inch) of the isolation on each wire.
4. Push the pin spring release next to each socket on the connector and insert
the correct wire end according to Connector Pinning, p. 6.
Connect the wires from the power supply to the connector in the same way as
the Ethernet wiring. Make sure that polarity is not reversed.
Anybus®Wireless Bolt™Installation Guide SCM-1202-006/SP2139 1.7
Configuration 8 (16)
3 Configuration
Anybus Wireless Bolt can be configured either by setting individual parameters
in the web interface or by using a pre-configured Easy Config mode.
Advanced configuration can be carried out by issuing AT (Hayes) commands in
the AT Commands tab in the web interface, or over Telnet to port 8080. A list of
the supported AT commands is available at www.anybus.com/support.
The Web Interface
The web interface is accessed by pointing your web browser to the IP address of
the internal web server in Wireless Bolt. The default address is 192.168.0.99.
Most configuration settings are self-explanatory. For detailed information about
the settings, see the Anybus Wireless Bolt User Manual.
The web interface is designed for the latest versions of Internet Explorer,
Chrome, Firefox and Safari. Other browsers may not be supported.
Anybus®Wireless Bolt™Installation Guide SCM-1202-006/SP2139 1.7
Configuration 9 (16)
Easy Config Modes
Mode Role Description
1 — (reserved)
2 — Reset the whole configuration to the factory defaults
3 — Reset the IP settings to the factory defaults
4 Client Await automatic discovery and configuration by a device
in Mode 5 (WLAN Access Point) or 6 (Bluetooth NAP)
5 WLAN AP Discover and reconfigure devices in Mode 4 as clients
6 Bluetooth NAP Discover and reconfigure devices in Mode 4 as clients
Modes 4, 5 and 6 can be used in combination to automatically set up a WLAN or
Bluetooth network of Wireless Bolt devices.
A device set in Mode 5 or 6 will scan for devices set in Mode 4. Each detected
device in Mode 4 will automatically be configured as a client, and the scanning
device will be configured as a WLAN or Bluetooth access point. The devices in
Mode 4 will then restart and attempt to connect to the access point.
Mode Timeout
The Mode 5 and 6 scans will run for 120 seconds. To scan for additional devices,
just activate the mode again.
Mode 4 will listen for 120 seconds or until it has received a valid configuration
from a Mode 5 or 6 device.
The IP address of a client may be changed by the configuration from the
access point. Active browser sessions could therefore be lost.
Anybus®Wireless Bolt™Installation Guide SCM-1202-006/SP2139 1.7
Altri manuali per Anybus Wireless Bolt Serial
1
Indice
Altri manuali HMS Hardware di rete
HMS
HMS Anybus Wireless Bridge II Guida utente
HMS
HMS Anybus Wireless Bolt RJ45 PoE Manuale utente
HMS
HMS Anybus Wireless Bolt Series Guida utente
HMS
HMS Ixxat CAN@net NT 200 Manuale utente
HMS
HMS Anybus 021440 Manuale utente
HMS
HMS Anybus X-gateway Modbus-TCP Manuale utente
HMS
HMS Anybus Wireless Bolt II Guida utente
HMS
HMS Anybus ABC4012 Guida utente
HMS
HMS Anybus AB7665 Manuale utente
HMS
HMS FLB 3271 Manuale utente
HMS
HMS Anybus Wireless Bolt Series Manuale utente
HMS
HMS IXXAT CANnector Bridge Manuale utente
HMS
HMS Anybus Wireless Bridge II Manuale utente
HMS
HMS eWON Cosy 131 Manuale utente
HMS
HMS AnyBus-X AB7607 Manuale utente
HMS
HMS Anybus Wireless Bolt CAN SP2937 Guida utente
HMS
HMS Anybus Wireless Bridge II Guida utente
HMS
HMS Ewon Flexy Series Manuale utente
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
