Hobbes GIGA-X Manuale utente
GIGA-X
LAN Speed /Link Verifier
Cable Length & Cable Faults Test
For
10/100/1000 BASE-T /TX
INTRODUCTION
Hobbes manufacturer has successfully leveraged Digital Signal Process (DSP) and
high-speed mixed signal expertise to develop the first low-cost Gigabit Cross-Over Cable tester.
GIGA-X helps deliver trouble-free Gigabit Ethernet deployments. It maps comprehensive
network layouts for 10/100/1000BASE-T Gigabit Ethernet physical layer, for use over Category-5
twisted pair copper cables.
GIGA-X is a single-port transceiver, which is able to identify cable length, “On-Line/Off-line”,
cable pair faults, network device speeds, and connections status. The results are then displayed
on the LED.
An economical and versatile tool, the GIGA-X complies with existing CATEGORIES IEEE
standards. With GIGA-X, upgrading and installing Giga-bits devices and cables in 10/100BASE-T
environments will be easier, faster, and more effective. The GIGA-X is also beneficial for minor
changes in a 10/100/1000BASE-T infrastructure upgrades.
FEATURES
•On-line speed and connection status
•10/100/1000BASE-T device speed auto-negotiation
•Measure length of cable by pair/s (in meters)
•Detect open or short status on cables or device ports
•Identify crossover cable and TX/RX auto switch ports
•Low Battery indicator
•Power ON LEDs self-test
SPECIFICATIONS
Dimension: 82 x 138 x 32mm (3.2 x 5.4 x 1.3 inches)
Weight: 125 g
Max test length Off-Line 150 meters (492.13 feet)
On-Line 110 meters (360.89 feet)
Power source 4 x AAA Alkaline batteries (1.5V*4)
Working Temperature 0ºC~50ºC (32ºF ~ 122ºF)
Storage Temperature -30ºC ~50ºC (-22ºF ~ 122ºF)
Humidity 10%~90%
Testing device has the following abilities:
1. Speed 1000/100/10 are supported
2. 10/100/1000 Full Duplex are supported
3. 10/100 Half Duplex are supported
4. 12,36,45,78 all 4 pairs linked
5. Auto swap (Flash means your device has the ability to swap
the TX and RX signals)
6. The cable length is 99 meters
Testing device has the following abilities:
1. The end of the cable was not connect to any device
2. The length of Pair 1 is 99 meters
Testing device has the following abilities:
1. Speed 10/100 are supported
2. 10/100 Full Duplex are supported
3. 10/100 Half Duplex are supported
4. 12,36, 2 pairs linked
5. The cable length is 22 meters
Testing device has the following abilities:
1. 3-6 pairs linked
2. 1-2 pair shorted
3. 4-5 and 7-8 port shorted
4. The cable is shorted at 10 meters from tester port
OPERATING INSTRUCTIONS
Note: Please check battery conditions before performing a test. Low battery may cause inaccurate
results.
1. ON/OFF switch is located on the side.
•Every time the unit is turned on, ALL LED’s will light up for a 3 second self-test.
2. Plug one side of terminated RJ-45cable into GIGA-X RJ-45 socket at the top, regardless
of whether or not the cable is still connected to Hub/Switch/NIC.
3. Press “TEST” button once.
•“Length” and “Fault Location” LED indicators will blink sequentially to
auto-negotiate (±5 seconds) with any network devices connected to it, either
Hub/Switch or NIC.
4. The diagnostic readout immediately detects results based on testing a cable in different
scenarios:
zCable connected to active or live network device (Hub/Switch or NIC).
- Speed Status LEDs (10/100/1000 and Full/Half duplex) will light up
according to the speed of the device.
- Link Status LEDs will light up according to the pair/s connected.
(1-2 & 3-6 for 10/100 device, 1-2/3-6/4-5/7-8 for Giga device)
- If cable is shorted or open, 4-5 /7-8 LED light up on 10/100 devices
-If Crossover LED is blinking, this indicates that the device port is
auto-swappable between TR and RX
zCable is not connected to any network device / floating cable.
- Speed Status and Link Status LED’s will not show results.
- Open LEDs on pair 1-2/3-6/4-5/7-8 will light up
- If cable is shorted, Short LED will light up
- Pressing Pair Debug once will measure the length of each pair indicated by
blinking LED.
zCable connected to a network device using crossover cable.
- Crossover LED will light up solid on pair 1-2/3-6 (10/100 device), or
1-2/3-6 & 4-5/7-8 (Giga device)
- If the Alpha-Numeric LED shows “CON”, this means that the cable length
is unable to be determined or that you are connected to a network device
that runs in 10BASE-T and Half-duplex mode.
Note: Due to the legacy 10BASE-T hardware constraints, in order to determine the
length of cable you must unplug the other end of the cable from its source and
retest it again as a floating cable.
Warning
1. Always turn off the unit to save battery power. Disconnect battery connection if the
GIGA-X is to be stored for an extended period.
2. GIGA-X is covered by a 2-year manufacturer’s warranty from the date of purchase.
Please contact the distributor/reseller where you originally purchased the product for
warranty or service.
3. Misuse or unreasonable treatment of the product will void the warranty.
4. LOW BAT. LED will light up when the voltage is lower than 2.2V. Please replace with a
new alkaline battery. Mixing old and new batteries is not recommended and may give
inaccurate results.
5. During LEDs self test if one or more LED’s are not lit up, please check or replace the
battery source. If the problem still persists, contact your distributor/reseller for warranty
or service.
Date of Purchase: ___________________
Serial Number: _____________________
Distributor info:
Indice
Altri manuali Hobbes Cavi di rete
