Hobby King TRAINSTAR Manuale utente
INSTRUCTION MANUAL
CAUTIONS:
This radio control model is not a toy! it is a technical
equipment,you must pay attention to the flying environment
and correct operation. Teenagers must fly with guardian.
Learner must fly with the experienced pilot.
TECHNICAL DESCRIPTION
Wing Span: 1400mm ( 55.12")
Length: 1060mm ( 41.7")
Flying Weight: 1300g
Battery: 11.1V/1800mAh/20C
Motor: Brushless 850KV
ESC: 30A Brushless ESC
For users aged 14 or over
PROTECT YOUR MODEL , YOURSELF &
OTHERS . . . FOLLOW THESE IMPORTANT
SAFETY PRECAUTIONS
1. Your airplane should not be considered a toy, but rather a sophisticated
working model that functions very much like a full - size airplane.
Because of its performance capabilities,the plane, if not assembled and
operated correctly, could possibly cause injury to yourself or spectators
and damage property.
2. You must assemble the model according to the instructions.Do not alter
or modify the model, as doing so may result in an unsafe or unflyable
model.In a few cases the instructions may differ slightly from the photo.
In those instances the written instructions should be considered as
correct.
3. If you are not an experienced pilot or have not flown this type of model
before, we recommend that you get the assistance of an experienced
pilot in your R/C club for your first flights. If you are not a member of a
club, your local hobby shop has information about clubs in your area
whose membership includes experienced pilots.
4. While this kit has been flight tested to exceed normal use, if the plane
will be used for extremely high stress flying, such as racing, or if an
engine larger than one in the recommended range is used, the modeler
is responsible for taking steps to reinforce the high stress points and/ or
substituting hardware more suitable for the increased stress.
We , as the kit manufacturer , provide you with a top quality ,
thoroughly tested kit and instructions, but ultimately the quality and
flyability of your finished model depends on how you build it ;
therefore,we cannot in any way guarantee the performance of your
completed model, and no representations are expressed or implied
as to the performance or safety of your completed model.
1
1 KIT CONTENTS
2 ASSEMBLE THE MODEL
1. Install all the servo horn by screw.
2. Insert the linker to the corresponding hole of the tail.
2
3. Put the horizontal tail onto the tail of the fuselage.
4. Insert the linker to the corresponding hole of stabilizer and fix it
with screw.
6. Connect the clevis to the servo horn of the tail.
5. Install the vertical tail onto the horizontal tail and fix it with screw.
3
7.Insert the push rod to the linker of the tail wheel.
9
. Install the motor to the front of the fuselage by screw and connect the
plug.
8.
Connect the tail wheel to the servo horn by the metal fixture and
install it on the tail by screw.
4
10. Install the cowling to the fuselage by screw.
11. Install the wheels to the main landing gear with wheel cover by crew.
5
12.
Install the main landing gear to the corresponding place under the
fuselage and fix it by the plastic cover.
13.
Insert the connection pipe into the main wing and connect both
part together.
6
14.
Put the main wing onto the fuselage and fix it with a plastic cover by screw.
16. Pick up a shaft fixture suitable for the motor shaft and install it to the propeller.
15.
install the servo arm to the aileron servo and connect the push rod
to the servo horn.
17. Insert the motor shaft to the spinner pedestal.
7
18.
Insert the motor shaft to the propeller and make sure the concavity of
the propeller face toward the tail and fix it by washer and nut.
19. Install the spinner with two screw.
20. The plane full assembled as shown in the figure.
Adjust the Trim Settings
8
Tip: Use the trim sliders on the transmitter
to adjust the control surfaces. Make
sure they are the same level to avoid
erratic flight characteristics . If you
cannot get the surfaces level , adjust
the length of the clevis and re-attach
them to the servo horn.
3CENTER OF GRAVITY
The ideal C.G.position is 58±5 mm behind the leading edge measured
at where the wing meets the fuselage . In order to obtain the C.G.
Specified ; add weight to the fuselage or move the battery position.
Check the C.G. before flying.
The C.G. (Center of Gravity) is the location on the wings, measured
back from the leading edge on both sides of the fuselage, where the
model balances. In addition to the control surface throws, the C.G.
has a GREAT effect on the way the model flies. If the C.G. is too far
aft (tail heavy), the model will be too responsive and difficult to
control. If the C.G. is too far forward (nose-heavy), the model will
be too stable and not responsive enough. Follow the instructions
to make sure the model is balanced properly and the C.G. is in the
correct location.
9
Indice
Altri manuali Hobby King Giocattolo
Hobby King
Hobby King Fly Baby-EP Manuale utente
Hobby King
Hobby King SBACH 55" Manuale utente
Hobby King
Hobby King Plug-N-Fly Paramotor Manuale utente
Hobby King
Hobby King Prime Jet Pro Manuale utente
Hobby King
Hobby King Mariposa Trainer Manuale utente
Hobby King
Hobby King MXS-R Manuale utente
Hobby King
Hobby King Electrolyte Manuale utente
Hobby King
Hobby King 12A BEC Manuale utente
Hobby King
Hobby King Airoso F3A Manuale utente
Hobby King
Hobby King Prime Jet Pro Manuale utente
Hobby King
Hobby King Delta Rocket 100 Manuale utente
Hobby King
Hobby King SuperG Manuale utente
Hobby King
Hobby King Gulfstream G500 ARF Manuale utente
Hobby King
Hobby King SU-35 FIGHTER Manuale utente
Hobby King
Hobby King Micro SU-27 Manuale utente
Hobby King
Hobby King Waco 30E Manuale utente
Hobby King
Hobby King ASK-2100 Manuale utente
Hobby King
Hobby King Arcus F3A Manuale utente
Hobby King
Hobby King SBACH-342 Thunderbol Manuale utente
Hobby King
Hobby King B-17G Manuale utente
