HomeBeyond E70-27 Istruzioni per il montaggio

Built-In Range Hood

IMPORTANT:

Read and save these instructions.

NOTICE:

Installer: Leave this guide with the homeowner

Homeowner: Keep this guide for future reference

Installation Guide

and Users Manual

Built-In Series Range hood

E70-27

version:2019a

Important Safety Notice

Read all Instructions before Installing and operating this appliance

The installation in this manual is intended for qualied installers, service technicians or persons with •

similar qualied background. Installation and electrical wiring must be done by qualied profession-

als and in accordance with all applicable codes and standards, including re-rated construction.

DO NOT• attempt to install this appliance yourself. Injury could result from installing the unit due to

lack of appropriate electrical and technical background.

Range hood may have very sharp edges; please wear protective gloves if it is necessary to remove any •

parts for installing, cleaning or servicing.

Activating any switch ON before completing installation may cause ignition or an explosion.•

Due to the size and weight of this range hood, two people installation is recommended.•

To reduce the risk of re, electric shock, or injury to persons:

For general ventilating use only. • DO NOT use to exhaust hazardous or explosive materials and va-

pors.

The combustion air ow needed for safe operation of fuel-burning equipment may be affected by this •

unit’s operation. Follow the heating equipment manufacturer’s guideline and safety standards such

as those published by the National Fire Protection Association (NFPA), and the American Society of

Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

Before servicing or cleaning unit, switch power OFF at service panel and lock service panel to pre-•

vent power from being switched ON accidentally.

Clean grease laden surfaces frequently. To reduce the risk of re and to disperse air properly, make •

sure to vent air outside. DO NOT vent exhaust into spaces between walls, crawl spaces, ceiling, attics

or garages.

Ducted fans MUST always be vented to the outdoors.•

Use only metal ductwork and this unit MUST be grounded.•

Sufcient air is needed for proper combustion and exhausting of gases through the duct to prevent •

back drafting.

When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hid-•

den utilities.

All electrical wiring must be properly installed, insulated and grounded.•

Old duct work should be cleaned or replaced if necessary to avoid the possibility of a grease re.•

Check all joints on duct work to insure proper connection and all joints should be properly taped.•

Use this unit only in the manner intended by the manufacturer. If you have questions, contact the •

vendor.

To reduce the risk of a stove top grease re:

Keep all fan, bafe, spaces, lter, grease tunnel, oil container and grease-laden surfaces clean. Grease •

should not be allowed to accumulate on fan, bafe, spaces, lter, grease tunnel and oil container.

Always turn range hood ON when cooking at high heat or when cooking aming foods. •

Use high settings on cooking range only when necessary.•

Never leave surface units unattended at high settings. Boil overs cause smoking and greasy spillovers •

that may ignite. Heat oils slowly on low or medium settings. Page 1

Page 2

Important Safety Notice

Read all Instructions before Installing and operating this appliance

WARNING

Your safety and the safety of others is very important. We have provided many important safety mes-

sages in this manual and on your appliance. Always read and obey all safety messages. All safety mes-

sages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can happen if the instructions are not followed.

This is the safety alert symbol. This symbol alerts you to potential hazards that can hurt you and others.

All safety messages will follow the safety alert symbol and the word “WARNING”.

The manufacturer and/or distributor/reseller declines all responsibility in the event of failure to ob-

serve the instructions given here for installation, maintenance and suitable use of the product.

The manufacturer and/or distributor/reseller further declines all responsibility for injury due to neg-

ligence and the warranty of the unit automatically expires due to improper maintenance.

The manufacturer and/or distributor/reseller will not be held responsible for any damages to per-

sonal property or real estate or any bodily injuries whether caused directly or indirectly by the range

hood.

Clean ventilating fan frequently.•

Always use appropriate cookware and utensils size.•

Always use cookware appropriate for the size of the surface element.•

To reduce the risk of injury to persons in the event of a stove top grease re:

SMOTHER FLAMES with a close-tting lid, cookie sheet, or metal tray, then turn OFF the burner. •

BECAREFUL TO PREVENT BURNS. NEVER PICK UP A FLAMING PAN—you may be burned.

KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the ames DO

NOT go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT or dial your local

emergency service immediately.

DO NOT USE WATER, including wet dishcloths or towels — a violent steam explosion will result.•

Use an extinguisher ONLY if:•

You know you have a Class A, B, C extinguisher, and you already know how to operate it.•

The re is small and contained in the area where it is started.•

The re department is being called.•

You can ght the re with your back to an exit.•

To reduce the risk of injury to persons in the event of a gas leaks:

Extinguish any open ame.•

DO NOT turn on the range hood fan or any type of ventilator.•

DO NOT turn on the lights or any type of appliance.•

Open all doors and windows to disperse the gas. If you still smell gas, call the gas company and re •

department, or dial your local emergency service immediately.

Page 3

Venting Requirements

Vent system must terminate to the out-•

side (roof or side wall), unless using a

recirculating kit.

Do not terminate the vent system in an •

attic or other enclosed area.

Do not use 4” (10.2 cm) laundry-type •

wall caps.

Use metal/aluminum vent only. Rigid •

metal/aluminum vent is recommended.

Do not use plastic vent.•

Always keep the duct clean to ensure •

proper airow.

Calculate the following gures before •

installation:

Distance from the oor to the ceil-1.

ing.

Distance between the oor to the 2.

countertop/stove (recommend 24in

to 30in).

Distance between the countertop/3.

stove to the range hood.

Height of hood and duct cover.4.

For the most efcient and quiet

operation:

It is recommended that the range hood •

be vented vertically through the roof

through 6” (15 cm) round metal/ alu-

minum vent work.

The size of the vent should be uniform.•

Use no more than three 90° elbows.•

Make sure there is a minimum of 24” •

(61 cm) of straight vent between the

elbows if more than one elbow is used.

Do Not install two elbows together.•

The length of vent system and number •

of elbows should be kept to a mini-

mum to provide efcient performance.

The vent system must have a damper. •

If roof or wall cap has a damper, Do

Not use damper supplied with the

range hood.

Use duct tape to seal all joints in the •

vent system.

Use caulking to seal exterior wall or •

roof opening around the cap.

Height & Clearance

Cabinet

Range hood

Venting Pipe

36” base

Min:

24”

Max: 30”

Page 4

IMPORTANT:

A minimum of 6” round (standard for this range hood) or 3-1/4 x 10” rectangular duct (purchased separate-•

ly) must be used to maintain maximum airow efciency.

Always use rigid type metal/aluminum ducts if available to maximize airow when connecting to provided •

duct.

Please use • Duct Run Calculation below to compute total available duct run when using elbows, transitions

and caps.

ALWAYS, when possible, reduce the number or transitions and turns. If long duct run is required, increase •

duct size from 6” to 7 or 8”. If a reducer is used, install a long reducer instead of a pancake reducer. Reduc-

ing duct size will restrict airow and decrease airow, thus reduce duct size as far away from opening as

possible.

If turns or transitions are required: Install as far away from opening and as far apart, between 2, as possible.•

Minimum mount height between range top to hood bottom should be no less than 24”.•

Maximum mount height should be no higher than 30”•

It is important to install the hood at the proper mounting height. Hoods mounted too low could result in heat •

damage and re hazard; while hoods mounted too high will be hard to reach and will loose its performance

and efciency.

If available, also refer to manufacturer’s height clearance requirements and recommended hood mounting •

height above range.

Minimum Duct Size:

Round- 6” minimum•

Rectangular- 3-1/4 x 10” minimum (requires a 6” to 3-1/4x10” adaptor not supplied)•

Duct Run Calculation:

Recommended maximum run

6” or 3-1/4 x 10” duct 50 ft

Vent piece deduction

Each 90º elbow used 9 ft

Each 45º elbow used 5 ft

Each 6” to 3/14 x 10” transition used 7 ft

Side wall cap with damper 0 ft

Roof cap 0 ft

Duct Run Calcuation example:

One roof cap, two 90º elbow, and one 45º elbow used:

0ft + 9ft + 9ft + 5ft = 23ft used.

Deduct 23ft from 50ft, 27ft maximum available for

straight duct run.

Calculating vent system length

To calculate the length of the system you need, deduct the equivalent feet for each vent piece used in the system

from the recommended maximum duct run.

Page 5

Venting Methods

This built-in range hood is factory set for venting through the roof or wall. For non-vented (re-circulating) •

installations, see Ductless Conversion (Non-Vented) below.

Vent work can terminate either through the roof or wall. To vent through a wall, a 90° elbow is needed.•

IMPORTANT:

NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or •

garages. All exhaust must be ducted to the outside.

Use metal/aluminum duct work only. •

Fasten all connections with sheet metal screws and tape all joints with certied Silver Tape or Duct Tape.•

Use caulking to seal exterior wall or roof opening around the cap.•

Ductless Conversion

Ductless conversion is intended for applications where an exhaust duct work is not possible to be installed. •

When converted, the hood functions as a purifying hood rather than an exhaust hood. Fumes and exhaust

from cooking is drawn and ltered by a set of charcoal lters. The air is then puried and re-circulated back

within the home.

We recommend to ALWAYS exhaust air outside of the home by employing existing or installing new duct •

work, if possible. Only when the exhaust option is not possible should you recourse to converting the hood

into a purifying unit.

When converted to be a “purifying” unit, a set of charcoal lters and an air-diverter are required in addition to •

its standard aluminum lter set. Available at your local authorized reseller. The standard aluminum lters are

intended to capture residue from cooking, the optional charcoal lters help to purify fumes exhausted from

cooking, and the optional air-diverter redirects ltered clean air back to the house.

Round Duct

Wall Cap

Round Elbow

Roof Cap

24” to 30” Above

Cooking Surface

Elite 50 Series

Range Hood

Page 6

Electrical Requirements

IMPORTANT: Observe all governing codes and ordinances.

(Please consult with a qualied electrician for 220-Volt 50 Hz voltage)

It is the customer’s responsibility:

To contact a qualied electrical installer.

To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/

NFPA 70 — latest edition*, or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22. 2 No. 0-

M91 - latest edition** and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualied electrician determine •

that the ground path is adequate.

A 120-volt, 60 Hz, AC-only, fused electrical supply is required on a separate 15-amp circuit, fused on both •

sides of the line.

Do not ground to a gas pipe.•

Do not have a fuse in the neutral or ground circuit.•

RISK OF ELECTRICAL SHOCK. This range hood must be properly grounded. Check with a qualied •

electrician if you are not sure whether the range hood is properly grounded.

The range hood should be connected directly to the fused disconnect (or circuit breaker) box through ex-•

ible armored or non-metallic sheathed copper cable. A U.L. - or C.S.A. - listed strain relief must be provid-

ed at each end of the power supply cable. Do not use extension cord or adapter plug with this appliance.

The range hood must be connected with copper wire/plug only.•

Always use plug provided. If not •

possible, connect three wires ac-

cording to its color (black to hot,

white to neutral, and green to

ground) to house wires and cap

with wire connectors:

Wire sizes (copper wire only) and connections must conform with the rating of the appliance as specied on the

model/serial rating label. Wire sizes must conform to the requirements of the National Electrical Code ANSI/

NFPA 70 — latest edition*, or CSA Standards C22. 1-94, Canadian Electrical Code Part 1 and C22. 2 No. 0-

M91 - latest edition** and all local codes and ordinances. A U.L. - or C.S.A. - listed conduit connector must be

provided at each end of the power supply cable (at the range hood and at the junction box).

Copies of the standards listed may be obtained from:

* National Fire Protection Association ** CSA International

Batterymarch Park 8501 East Pleasant Valley Road

Quincy, Massachusetts 02269 Cleveland, Ohio 44131-5575

Charcoal Filter Installation Methods

Severe Injury

Hood may have very shape edges. Please wear

protective gloves if it is necessary to remove

any parts for installing, cleaning or servicing.

NOTE: The charcoal lters might preinstalled if you purchased the range hood with re-circulating kit from us.

Remove grease lter on hood.1.

Position the charcoal lters onto each side of the motor and turn until it locks. Re-install aluminum lters.2.

Charcoal lters should be replaced after 120 hours of use (or approximately every 2 to 3 months based on 3.

the average of 1 to 2 hours of daily cooking time).

Severe Injury

Hazard of electrical shock!

Electrical wiring must be done

by qualied person

Page 7

Installation

Excessive Weight

Require two or more person to move and

install this range hood. Spinal or other bodi-

ly injuries could occur if it is not followed.

INSTALL THE HOOD

Due to excessive weight, two or more person is recommended for this step.

NOTE: the hood has to be installed, inside the cabinet, at

minimum 1-1/2” from the rear wall cabinet and at 2” from the front wall cabinet.

The internal height of cabinet has to be minimum 28”.

The hood should be mounted centered over the cook top burners.

Remove the decorative panel from the range hood.1.

Cut a hole in the bottom of the cabinet, using the dimensions shown in the table below (ref. to Fig. A).2.

Insert the hood in the cabinet and secure with the (4) mounting screws from the inner side of the range hood 3.

(Fig. B). Note: Wood blocking might need to be built if it’s not available in order to secure the mounting

screws.

In the Non-Ducted Recirculation Conguration, install the Non-ducted recirculation Filter before replacing 4.

the grid (see section “Non-ducted recirculation lter installation”).

Replace the decorative panel.5.

Wood Blocking

Fig. B

Fig. A

Cut a hole in the bottom of the

cabinet

Model X Y

E50-20 19 1/2” 11 1/4”

E50-28 25 1/2” 11 1/4”

E70-27/S27 26 1/2” 10 3/4”

E70-30/S30 28 1/2” 10 3/4”

Page 8

Range Hood Operations

Wiring Diagram

Turn On:

Press the speed control (Quiet Speed, Low Speed, High Speed) switch to select the desired level of•

power. Once button is pressed, the previous speed mode will cancel.

Press the Light Switch to power on the lights.•

Turn Off:

Press the Power Switch to turn off the power.•

Press the Light Switch to power off the lights•

Page 9

Troubleshooting

If the range hood does not operate after installa-1.

tion:

Check if the range hood has been plugged in, make •

sure that all power has been turned back on and all

electrical wiring are properly connected.

Swap out light assembly to working ones to deter-•

mine whether it is caused by defective bulbs. (See

Replacing the light bulbs, page 11)

The range hood vibrates when the blower is on:2. The range hood might not have been secured prop-•

erly on to the ceiling.

The blowers seems weak:3. Check that the duct sized used is at least 6” or •

3-1/4 x 10”. Range hood WILL NOT function

efciently with insufcient duct size. For example:

7” duct over 6” hole and loosely secured.

Check if duct is clogged or if damper unit is not •

opening properly. A tight mesh on a side wall cap

unit might also cause restriction to the air ow.

The lights work but the blower is not spinning at 4.

all, is stuck or is rattling.

The blower might be jammed or scraping the bot-•

tom due to shipping damage.

The hood is not venting out properly:5. Make sure the distance between the cook top and •

the bottom of the hood is within 24” and 30” in

range.

Reduce the number of elbows and length of duct •

work. Check if all joints are properly connected,

sealed, and taped.

Make sure the power is on high speed for heavy •

cooking

NOTE: For all other inquiries, please contact us. Our contact information can be found on the back cover page.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali HomeBeyond Cappa di ventilazione

HomeBeyond

HomeBeyond Built-In Series Istruzioni per il montaggio

Manuali Cappa di ventilazione popolari di altre marche

emmeti

emmeti RECUPA MED A-140 Guida

Nibe

Nibe F135 Manuale utente

Kuppersberg

Kuppersberg INTRO 60 Istruzioni di installazione e manutenzione

Zephyr

Zephyr Spruce AK9834BS Guida all'installazione

Hisense

Hisense MH6INBG Manuale utente

Miele

Miele DA 1255 Manuale utente

Broan

Broan 46000 Manuale utente

GE Profile PV977 Istruzioni originali

FALMEC

FALMEC FFRIA24W5FS Manuale utente

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuale utente

Küppersbusch

Küppersbusch DX ISLA Manuale utente

ETNA

ETNA AV360RVS Manuale utente

JUNO

JUNO JDF603E6 Manuale utente

Miele

Miele DA 6708 D Manuale utente

Tricity Bendix

Tricity Bendix LE 150 Manuale

AEG

AEG X68163BV1 Manuale utente

AEG

AEG 125 D Manuale utente

Smeg

Smeg KSEV97X Manuale utente