Honeywell UV100E2009 - Ultraviolet Air Treatment... Manuale utente

69-1573-3

UV100E Ultraviolet System

OWNER’S GUIDE

UV100E ULTRAVIOLET SYSTEM

69-1573—3 2

IMPORTANT

Please read these instructions and keep them in your records.

HOW YOUR ULTRAVIOLET AIR TREATMENT SYSTEM

OR SURFACE TREATMENT SYSTEM WORKS

Your UV System uses patented SmartLamp™ control technology that monitors the

HVAC system to operate the lamp only when needed. This technology extends bulb

life up to five times and reduces power consumption, lowering operating costs. Your

UV System also includes protection from extreme conditions that may be found in your

heating and cooling system and local diagnostics with the SmartLamp™ LED and

reset capability.

Depending on installation, your UV System can operate as an Air Treatment System or

as a Surface Treatment System.

Air Treatment System

Installed in the return air duct of your system, your Ultraviolet Air Treatment System

kills a high percentage of airborne germs circulating through your forced air heating

and cooling system. Individual results depend on careful installation and maintenance

and on the actual amount of time your system fan operates. See Fig. 1.

Your Ultraviolet Air Treatment System uses the on-board air flow sensor or input from

the Enviracom™ communication terminals to monitor air flowing through your heating

and cooling system. The UV system turns on when air is flowing and leaves the lamp

on for 40 minutes after the airflow stops. If airflow resumes during the 40 minutes, the

timer resets to 40 minutes. When no airflow is detected for 40 minutes, the lamp turns

off until the next occurrence of airflow.

Fig. 1. Typical Air Treatment System installations.

M22858

WARNING/A

VERTISSEMENT

Nocifs pour lapeaunueetles

Veuillezlireetbiencomprendre

l’installation et lamaintenance.

WARNING/AVERTISSEMENT

Nocifspourla peaunueetles

Veuillezlireetbiencomprendre

l’installationetlamaintenance.

UV100E ULTRAVIOLET SYSTEM

3 69-1573—3

Surface Treatment System

When installed next to the cooling coil of your system, your Ultraviolet Surface

Treatment System prevents a high percentage of the growth of micro-organisms such

as mold that may grow on duct surfaces, coils, and drain pans. Individual results

depend on careful installation and maintenance. See Fig. 2.

Your Ultraviolet Surface Treatment System operates a steady three-hours-on/

three-hours-off cycle. With Enviracom™ communication terminals hooked up,

your UV System turns off for the Winter 30 days after the last call for cooling occurs.

And your UV System turns on and resumes the on/off cycle with the first call for cooling

in the Spring.

Fig. 2. Typical Surface Treatment System installations.

You can capture and minimize micro-organisms passing through your forced air system

when you combine your UV System with a high-efficiency air filtration system like an

electronic air cleaner. Talk to your installer about adding an electronic air cleaner to

complement your UV System and provide added protection for you and your family.

Enviracom™ Communications Capabilities:

• Communicates with homeowner through three-wire communication bus using

24 Vac thermostat connections.

—Hooked up to Air Treatment System (single-bulb and dual-bulb) models: uses

thermostat load information instead of airflow sensor.

—Hooked up to Surface Treatment System model: uses thermostat load

information to operate during times evaporator coil may be exposed to

moisture to extend lamp life beyond two years.

• Sends messages to communicate reset and receives remote reset, when available.

— Bulb change indication cannot be reset by cycling power.

— When Enviracom is transmitting messages, shows flashing green Enviracom

LED on bottom of unit.

When Enviracom is transceiving messages, shows solid green Enviracom LED on

bottom of unit.

M22860

WARNING/AVERTISSEMENT

Nocifs pour la peau nue et les

Veuillezlire et bien comprendre

l’installation et la maintenance.

WARNING/A

VERTISSEMENT

Nocifs pourlapeaunueet les

Veuillezlireetbiencomprendre

l’installationetlamaintenance.

UV100E ULTRAVIOLET SYSTEM

69-1573—3 4

BE SURE TO READ WARNINGS AND CAUTIONS

BEFORE USING YOUR UV SYSTEM

WARNING

UV Light Hazard.

Harmful to bare skin and eyes.

Can cause temporary or permanent loss of vision.

Never look at bulbs while illuminated.

View illumination only through light indicator located on lamp handle.

To prevent exposure to ultraviolet light, disconnect power to Ultraviolet System

before servicing any part of heating and air conditioning system.

Do not mount device in location that allows ultraviolet light to be seen after

installation.

Do not attempt to bypass duct mount switch.

Do not attempt to open housing; unit is sealed to prevent ultraviolet light

exposure.

CAUTION

Personal Injury Hazard.

Power supply can cause electrical shock.

Disconnect power supply before cleaning or replacing ultraviolet bulb(s).

Do not open base unit or lamp handle; there are no user-serviceable

components inside.

CAUTION

Breakable Glass Hazard.

Can cause personal injury.

Be careful when inserting bulb(s) into lamp base.

Wear protective gloves when handling bulb(s).

CAUTION

UV Lamp Burn Hazard.

Harmful to bare skin.

Can cause severe burns.

Disconnect power 15 minutes before removing ultraviolet bulb(s).

UV100E ULTRAVIOLET SYSTEM

5 69-1573—3

MERCURY NOTICE

This device contains mercury in the sealed ultraviolet bulb(s). Do not place

your used bulb(s) in the trash. Dispose of properly.

Broken Bulb Cleanup.

Do not use a household vacuum.

Sweep debris (phosphor/glass) into a plastic bag and dispose of properly.

Contact your local waste management authority for instructions regarding

recycling and the proper disposal of old bulb(s).

UV100E ULTRAVIOLET SYSTEM

69-1573—3 6

HOW YOU CAN CHECK YOUR ULTRAVIOLET SYSTEM

Your UV System is designed to prevent accidental contact with electrical voltage and

with ultraviolet rays in the sealed unit⎯the ultraviolet lamp does not illuminate unless

the base is mounted on your forced air system duct.

It is recommended that every month you verify that your ultraviolet lamp is operating.

View the bulb only through the lamp light indicator on the lamp handle. See Fig. 3.

Do not attempt to look into the duct at the illuminated bulb(s).

If the light is not on when you check your UV System, briefly push the reset button for

one second. This brings the lamp on for 40 minutes (Air Treatment System) or for 30

minutes (Surface Treatment System). Pressing the reset button for five seconds resets

all internal timers. Cycling power does not reset the internal timers.

Fig. 3. Lamp light indicator, LED change indicator and reset button.

The LED indicator on the front of your UV System operates as follows:

aBulb life means emitting adequate amount of UV-C energy to maintain an effective kill

rate. At 0% bulb life remaining, the bulbs continue to operate until catastrophic bulb

failure (bulb burns out) but the kill rate becomes rapidly negligible.

LED Status Indicates Homeowner Action

Off 100 to 11% bulb lifearemaining Nothing

Flashing 10 to 1% bulb lifearemaining Purchases bulb(s)

Solid 0% bulb lifearemaining Replaces bulb(s)

M22856

LAMP LIGHT INDICATOR

LED CHANGE INDICATOR

RESET BUTTON

UV100E ULTRAVIOLET SYSTEM

7 69-1573—3

HOW YOU CAN MAINTAIN YOUR UV SYSTEM

You should regularly clean your UV System to maintain peak effectiveness of your air

treatment or surface treatment system. Replace the ultraviolet bulb when LED status

light on the front of your UV System is on steadily.

Quarterly Bulb Cleaning

Bulb cleaning is recommended as routine maintenance four times a year or every

three months. Use the UV Bulb Cleaning Reminder Schedule, Fig. 4, to help establish

and track your regular cleaning schedule.

Fig. 4. UV bulb cleaning reminder schedule.

To clean your bulbs:

1. Disconnect the power to your heating and cooling system.

2. Unplug or turn off power to your UV System and allow the bulb to cool for at

least 15 minutes.

YEAR

UV BULB CLEANING REMINDER SCHEDULE

, (year)

M13516A

JFMAMJJASOND

INSTALLATION DATE: (month)

UV100E ULTRAVIOLET SYSTEM

69-1573—3 8

3. Rotate your lamp handle counterclockwise and gently pull the lamp handle to

remove the bulb. See Fig. 5.

Fig. 5. Remove lamp bulb.

4. Holding the lamp handle, wipe the lamp glass using a soft cloth dampened with

glass cleaner. If you touch the lamp glass with your hands, be sure to clean the

area of any oils left from bare hands. See Fig. 6.

Fig. 6. Clean glass with soft cloth.

5. Also wipe away any dust that may have collected between the lamp light

indicator base and the black bulb base. See Fig. 7.

Fig. 7. Wipe lamp light indicator base.

M22842

M22844

LAMP LIGHT INDICATOR BASE

M22846

UV100E ULTRAVIOLET SYSTEM

9 69-1573—3

6. Dry bulb with a clean, dry cloth.

7. Insert the bulb into the base with the lamp light indicator at the eleven o’clock

position. Continue pushing and gently rotating counterclockwise until the lamp

handle inserts fully into the base. See Fig. 8.

Fig. 8. Position bulb for insertion back into the lamp base.

8. Rotate the lamp handle clockwise until it snaps into place with the lamp light

indicator aligned with the raised button on the unit cover. See Fig. 9.

Fig. 9. Snap bulb into place.

M22848

M22850

UV100E ULTRAVIOLET SYSTEM

69-1573—3 10

9. Reconnect power to your UV System.

10. For UV Air Treatment Systems, wait ten minutes for the airflow sensor to

calibrate. During this time, the furnace fan must remain off.

NOTE: Failure to wait ten minutes for the airflow sensor to calibrate before powering

the system fan causes the airflow sensor to incorrectly calibrate and the

device to incorrectly function. If this occurs, remove power to the furnace or

turn off the system fan, wait ten minutes, and then resume normal fan

operation.

11. Verify that your ultraviolet bulb is operating by viewing only through the lamp

light indicator on the lamp handle. Never look directly at your bulb while

it is illuminated.

12. Reconnect power to your heating and cooling system.

Bulb Replacement

Replacement of the bulb in your ultraviolet lamp when the LED is solidly lighted is

required to maintain effectiveness.

1. Obtain the correct replacement bulb/handle assembly or replacement bulb for

your unit. See Table 1.

2. Disconnect the power to your heating and cooling system.

3. Unplug or turn off power to your UV System and allow the bulb to cool for at least

15 minutes.

4. Rotate the lamp handle counterclockwise and gently pull the lamp handle to

remove the bulb. See Fig. 5.

Table 1. Select a Replacement Bulb/Handle Assembly or Replacement Bulb.

Unit Description

Replacement Bulb/

Handle Assembly

SnapLamp™

Replacement Bulb

UV100E1043

Air Treatment System

UC100E1006 UC18W1004

UV100E2009

Air Treatment System

UC100E1030

(two needed)

UC36W1006

(two needed)

UV100E3007

Surface Treatment System

UC100E1030 UC36W1006

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Honeywell Purificatore d'aria

Honeywell

Honeywell Enviracaire 17005 Manuale utente

Honeywell

Honeywell HPA-051 Series Manuale utente

Honeywell

Honeywell HPA030B Manuale utente

Honeywell

Honeywell F300 Manuale utente

Honeywell

Honeywell F111 Series 3 Manuale operativo

Honeywell

Honeywell F50F Manuale utente

Honeywell

Honeywell CL60PM Series Manuale utente

Honeywell

Honeywell CR10A Manuale del proprietario

Honeywell

Honeywell HHT-013-HD Manuale utente

Honeywell

Honeywell F50F Manuale utente

Honeywell

Honeywell F200 Manuale utente

Honeywell

Honeywell HPA100WE Manuale utente

Honeywell

Honeywell F50E Manuale utente

Honeywell

Honeywell HAP-16200E Manuale utente

Honeywell

Honeywell InSight Series Manuale utente

Honeywell

Honeywell HPA090 series Manuale utente

Honeywell

Honeywell 50100 - Enviracaire Air Purifier Manuale utente

Honeywell

Honeywell High Performance Air Purifier HFD-135 Manuale utente

Honeywell

Honeywell HPA830 Manuale utente

Honeywell

Honeywell HFD360 Series Manuale utente

Honeywell

Honeywell UV100A Manuale utente

Honeywell

Honeywell F50F Manuale operativo

Honeywell

Honeywell Quietclean HFD140 Series Manuale utente

Honeywell

Honeywell F58F Manuale utente

Manuali Purificatore d'aria popolari di altre marche

IKEA

IKEA UPPÅTVIND Manuale utente

Nash

Nash AP-1 PureSmart Manuale utente

LG PH-U450 Series Manuale utente

DeLonghi

DeLonghi DDSX 220WFA Manuale utente

Mitsubishi Electric

Mitsubishi Electric MA-E85R-E Manuale utente

Sharp

Sharp FU-40SE Manuale utente

Philips

Philips AC2721 Manuale utente

Hitachi

Hitachi EP-A3000 Manuale utente

TruSens

TruSens Z-2000 Manuale utente

Motorola

Motorola MBP87SN Manuale utente

Beko

Beko ATP 7100I Manuale utente

Carrier

Carrier INFINITY 1620 Manuale utente

AtmosAir

AtmosAir P2002 Manuale utente

Winix

Winix NK300 Manuale utente

Friedrich

Friedrich C-90A Istruzioni per l'uso e l'installazione

Surgically Clean Air

Surgically Clean Air JADE2.0 Manuale utente

Base aire

Base aire 555 Pro Manuale utente

Champion

Champion CP25 Manuale utente