Honeywell T775M Manuale del proprietario
To program the controller, perform the following procedures in the order listed:
Fig. 1
Press the MENU button, then select PROGRAM and press the button to view the
program menu.
Fig. 1 shows the Program menu for controller.
Fig. 2
1. From the menu, use the and buttons to highlight MOD 1.
2. Press the button to select MOD 1 to view the parameters. Fig. 2 shows
RELAY 1. In MOD 1, THROT RNG replaces DIFFERNTL.
!"#
Fig. Program – Setpoint
1. From the menu, use the and buttons to highlight SETPOINT.
2. Press the button to display the setpoint value.
3. Use the and buttons to increase/decrease the desired setpoint
temperature.
Set the temperature to 55°F.
4. Press the button to accept the setpoint temperature and display the next
option.
!"$%&'!"$&"$
Fig. Program – Throttling Range
1. From the menu, use the and buttons to highlight THROT RNG.
2. Press the button to display the throttling range value.
3. Use the and buttons to increase/decrease the desired value.
Set the value to 10°F.
4. Press the button to accept the value and display the next option.
( " &
Fig. Program – Sensor
1. From the menu, use the and buttons to highlight SENSOR.
2. Press the button to display the sensor selections.
3. Use the and buttons to select Sensor A or B.
Select sensor B.
4. Press the button to accept the highlighted sensor and display the next option.
)%*'
Fig. Program Heat/Cool
1. From the menu, use the and buttons to highlight HEAT/COOL (Default:
HEAT).
2. Press the button to display the heat and cool selections.
3. Use the and buttons to select Heat or Cool.
Select COOL.
4. Press the button to accept the highlighted selection and display the next
option.
+
Press the button to accept the highlighted selection EXIT. This will display the main
Program Menu screen (Fig. 1)
Fig. 1
("+,#-
1. From the menu, use the and buttons to highlight MOD 2.
2. Press the button to select MOD 2 to view the parameters.
( !"#
Fig. Program - Setpoint
1. From the menu, use the and buttons to highlight SETPOINT.
2. Press the button to display the setpoint value.
3. Use the and buttons to increase/decrease the desired setpoint
temperature.
Set the temperature to 55°F.
4. Press the button to accept the setpoint temperature and display the next
option.
( !"$%&'!"$&"$
Fig. Program – Throttling Range
1. From the menu, use the and buttons to highlight THROT RNG.
2. Press the button to display the throttling range value.
3. Use the and buttons to increase/decrease the desired value.
Set the value to 10°F.
4. Press the button to accept the value and display the next option.
(( " &
Fig. Program – Sensor
5. From the menu, use the and buttons to highlight SENSOR.
6. Press the button to display the sensor selections.
7. Use the and buttons to select Sensor A or B.
Select sensor A.
8. Press the button to accept the highlighted sensor and display the next option.
()%*'
Fig. Program Heat/Cool
5. From the menu, use the and buttons to highlight HEAT/COOL (Default:
HEAT).
6. Press the button to display the heat and cool selections.
7. Use the and buttons to select Heat or Cool.
Select HEAT.
8. Press the button to accept the highlighted selection and display the next
option.
_____________________________________________________________________
(+
Press the button to accept the highlighted selection EXIT. This will display the main
Program Menu screen (Fig. 1)
Fig. 1
)"+,&'.-
1. From the menu, use the and buttons to highlight RELAY 1.
Fig. 2
2. Press the button to select RELAY 1 to view the parameters.
) !"&'.
Fig. Program - Setpoint
1. From the menu, use the and buttons to highlight SETPOINT (Fig. 2).
2. Press the button to display the setpoint value.
3. Use the and buttons to increase/decrease the desired setpoint
temperature.
Set the temperature to 100°F.
4. Press the button to accept the setpoint temperature and display the next
option.
_____________________________________________________________________
)#!&"!' !"$
Fig. Program – Differential
1. From the menu, use the and buttons to highlight DIFFERNTL.
2. Press the button to display the differential value.
3. Use the and buttons to increase/decrease the desired value.
Set the value to 10°F.
4. Press the button to accept the value and display the next option.
)( " &
Fig. Program – Sensor
1. From the menu, use the and buttons to highlight SENSOR.
2. Press the button to display the sensor selections.
3. Use the and buttons to select Sensor A or B.
Select sensor A.
4. Press the button to accept the highlighted sensor and display the next option.
))%*'
Fig. Program Heat/Cool
1. From the menu, use the and buttons to highlight HEAT/COOL (Default:
HEAT).
2. Press the button to display the heat and cool selections.
3. Use the and buttons to select Heat or Cool.
Select HEAT.
4. Press the button to accept the highlighted selection and display the next
option.
+
Fig. Program – Exit
Press the HOME button to leave programming mode and return to the home screen.
This completes the programming procedure.
Indice
Altri manuali Honeywell Controllori
Honeywell
Honeywell CIPer 50 Manuale di installazione e funzionamento
Honeywell
Honeywell H808C Manuale utente
Honeywell
Honeywell IPC5000 Manuale utente
Honeywell
Honeywell S7014A Series Manuale utente
Honeywell
Honeywell CN34 Series Manuale operativo
Honeywell
Honeywell Touchpoint Plus Guida utente
Honeywell
Honeywell RA116A Manuale utente
Honeywell
Honeywell T775R 2000 Series Manuale utente
Honeywell
Honeywell GENT Mimic LED Driver Card Manuale di istruzioni
Honeywell
Honeywell Excel 10 Manuale utente
Honeywell
Honeywell PRESSURETROL L404F Manuale operativo
Honeywell
Honeywell HPMOM6CB Manuale utente
Honeywell
Honeywell Experion C300 Manuale utente
Honeywell
Honeywell UMC800 Manuale utente
Honeywell
Honeywell Enraf Manuale utente
Honeywell
Honeywell V8200 Manuale utente
Honeywell
Honeywell ACS-2plus Manuale utente
Honeywell
Honeywell T775U Series Manuale utente
Honeywell
Honeywell Spyder PUB6438S Manuale utente
Honeywell
Honeywell Design and Application Manuale del prodotto
