Honeywell UDC 6300 Guida
11/99 Kit Instruction 51-52-33-85C 1 of 5
UDC 6300 Process Controller
Upgrade PROM
Replacement Instruction
Document Number Form: 51-52-33-85C
Effective: 11/99
Supersedes: 3/99
Kit contents This kit contains one of the following Upgrade PROMs
Description Part Number
Adaptive Tune 51450900-501
Adaptive Tune + Math 51450900-502
Adaptive Tune + 2 Loops + Cascade 51450900-503
All Options 51450900-504
TPS Integration 51309350-501
Modbus RTU 51309350-502
Basic PROM 51309181-501
Equipment needed
• Phillips Head Screwdriver
• Flat Bladed Screwdriver
• Small Pliers
Continued on next page
2 of 5 Kit Instruction 51-52-33-85C 11/99
Replacement Instruction, Continued
How to remove the
chassis Refer to Figure 1 for reference and follow the procedure listed in Table 1.
Table 1 How to Remove the Chassis
Step Action
1 Pull down the flap covering the front screw and loosen the screw.
2 Grasp the bezel and pull the chassis out of the case.
Figure 1 Chassis Removal
Rear of case
23045
Front Screw
Bezel/Keyboard/Display Assembly
Continued on next page
11/99 Kit Instruction 51-52-33-85C 3 of 5
Replacement Instruction, Continued
How to install the
PROM
Table 1 How to Install the PROM
Step Action
1 The PROM is located on the MCU/Input printed wiring board at
location U109. See Figure 2 for location.
If a Communications Board is not present:
2 Lay the chassis on its left side on a non conductive surface
3 Insert a small screwdriver under the PROM and lift up to remove.
4 Orient the PROM to the socket and press into place.
5 Return the chassis to the case and configure the controller to include
the new features.
If a Communications Board is present:
6 Go to Table 2.
Figure 2 Parts Identification
23044
Rear of case
Front Screw
Communications
PWB
MCU/Input PWB
Option Input PWB
Power/ DIO PWB
Bezel/Keyboard/
Display Assembly
SpacerInterconnect
Interconnect
PWB Mounting Screws (4)
Cable Assembly
Power/DIO PWB
to Option Input Board
Mounting Screw
Chassis
EEPROM
at U106
PROM
(on MCU/Inputs
board at U109)
Continued on next page
4 of 5 Kit Instruction 51-52-33-85C 11/99
Replacement Instruction, Continued
How to remove the
Bezel/Keyboard/
Display assembly
In order to access the PROM if your controller has a Communications
Board, you must remove the Bezel/Keyboard/Display assembly from the
chassis and access the printed wiring boards.
The procedure in Table 2 lists the steps required to remove the
Bezel/Keyboard/Display assembly.
Table 2 How to Remove the Bezel/Keyboard/Display Assembly
Step Action
1 Remove the two screws on the bottom of the chassis frame that hold
the Bezel/Keyboard/Display assembly in place on the chassis frame.
Refer to Figure 2 for reference.
2 Lift the two retainers slightly away from the MCU/Input board notch
and the Power/DIO board on the opposite side as shown below.
The Bezel/Keyboard/Display board assembly will come away in one
piece.
Power/DIO
Board
MCU/Input
Board
Lift
retainers
here
Top of
rubber bezel
UDC6300
3 Install the PROM supplied in this kit.
See Table 3.
4 Reinstall the Bezel/Keyboard/Display assembly.
CAUTION Be careful to align the pins on the display board with
the mating connector P9 on the MCU/Input board.
5 Reattach the bezel assembly to the chassis with the screws
previously removed.
Continued on next page
11/99 Kit Instruction 51-52-33-85C 5 of 5
Replacement Instruction, Continued
How to install the
PROM Follow the procedure in Table 3 to access the PROM.
Table 3 Access the PROM
Step Action
1 Remove the four screws (two on each side) that hold the two main
printed wiring boards onto the chassis (See Figure 2 for location)
2 Use pliers to squeeze the ends of the spacer and push it through
the Power/ Digital I/O PWB. (See Figure 2 for location of spacer)
3 Gently pull the MCU/Inputs and the Power/DIO boards apart out of
the top and bottom interconnectors and lay the boards flat on a
non-conductive surface. (See figure 3).
4 Identify the Communications Option board (If present) and remove
the two screws that hold it onto the MCU/Inputs PWB.
5 Figure 3 identifies the location of the PROM.
6 Insert a small screwdriver under the PROM and lift up to remove.
7 Orient the PROM to the socket and press into place.
8 Reassemble the Communications Option PWB to the MCU/Inputs
PWB.
9 Reassemble the interconnects to the MCU/Inputs board and
reassemble the boards reversing the procedure above.
10 Reattach the Bezel/Keyboard/Display board assembly as listed in
Table 2 - steps 4 and 5.
11 Return the chassis to the case and configure the controller to
include the new features.
Figure 3 Printed Wiring Board Identification
Communications
Option Board
Option
Input Board
Power / DIO Board
MCU/Inputs
Board
W1
J14
P14
W1
U109
PROM Location
Pin 1
23046
Indice
Altri manuali Honeywell Controllori
Honeywell
Honeywell Lyric Manuale di istruzioni
Honeywell
Honeywell LKS 160 Manuale utente
Honeywell
Honeywell Scan Dome ll HTX-2500 Manuale del proprietario
Honeywell
Honeywell L4188 Manuale utente
Honeywell
Honeywell M896 Manuale utente
Honeywell
Honeywell 1000 Series Manuale utente
Honeywell
Honeywell S05 Series Manuale utente
Honeywell
Honeywell HCE80R Manuale utente
Honeywell
Honeywell MS4620F Manuale utente
Honeywell
Honeywell PRO 2000 Series Manuale utente
Honeywell
Honeywell S9361A207 Series Manuale utente
Honeywell
Honeywell XL 800 Series Manuale di installazione e funzionamento
Honeywell
Honeywell ML7421A1032 Manuale operativo
Honeywell
Honeywell Spyder 7 Manuale utente
Honeywell
Honeywell Vista Automation Module Manuale utente
Honeywell
Honeywell T775U Series Manuale utente
Honeywell
Honeywell VMM Series Manuale operativo
Honeywell
Honeywell S9360B Manuale utente
Honeywell
Honeywell CIPer 50 Manuale di installazione e funzionamento
Honeywell
Honeywell touchpoint Pro Manuale utente
