Honeywell ScanQuest IS4100 Series Manuale utente
IS4100 ScanQuest®Series
Laser Scan Engine
Installation and User’s Guide
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make changes in
specifications and other information contained in this document without prior notice,
and the reader should in all cases consult HII to determine whether any such
changes have been made. The information in this publication does not represent a
commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omissions contained herein:
nor for incidental or consequential damages resulting from the furnishing,
performance, or use of this manual.
This document contains propriety information that is protected by copyright. All
rights reserved. No part of this document may be photocopied, reproduced, or
translated into another language without the prior written consent of HII.
© 1998 - 2010 Honeywell International Inc. All rights reserved.
Web Address: www.honeywellaidc.com
Trademarks
Metrologic is a registered trademark of Metrologic Instruments, Inc. or Honeywell
International Inc.
Other product names mentioned in this manual may be trademarks or registered
trademarks of their respective companies and are the property of their respective
owners.
TABLE OF CONTENTS
Introduction
Theory of Operation...............................................................................1
Accessories ...........................................................................................2
Components of the ScanQuest Engine .................................................3
Label Locations .....................................................................................4
Maintenance ..........................................................................................4
Automatic Scan Activation ........................................................................5
Applications and Protocols........................................................................5
Design Specifications
Operational ............................................................................................6
Maintenance ..........................................................................................6
Mechanical ............................................................................................7
Electrical ................................................................................................7
Environmental........................................................................................8
Compliance............................................................................................8
IS4125 Depth of Field ...............................................................................9
IS4125 Object Detection .........................................................................10
Design Specifications
Specifications for the Supplemental Window ......................................11
Default Settings
IS4125 Communication Parameters ...................................................12
Scanner Terminations
IS4125-47 Connector Pin Assignments ..............................................18
IS4125-38 Connector Pin Assignments ..............................................19
IS4125-41, IS4125-63 & IS4125-76 Connector Pin Assignments ......20
IS4125-163 Connector Pin Assignments ............................................21
IS4110 Connector Pin Assignments....................................................22
iii
iv
TABLE OF CONTENTS
Scan Sense Timing
IS4110 Timing Diagram.......................................................................23
Regulatory Requirements and Warnings
Regulatory Requirements....................................................................24
Europe .................................................................................................25
United States .......................................................................................26
Canada ................................................................................................27
Warnings..............................................................................................27
Limited Warranty .....................................................................................28
Patents ....................................................................................................29
Index........................................................................................................30
Customer Support ...................................................................................32
Technical Assistance...........................................................................32
Product Service and Repair.................................................................33
1
INTRODUCTION
Honeywell’s IS4125 ScanQuest®Engines are compact laser bar code scanners
designed to be integrated with OEM devices. The ScanQuest series provides
fast, accurate, reliable scanning in a compact, lightweight package.
The IS4125 has built-in decoding for versatile OEM operations. The IS4125 has
flash upgradeable firmware. The IS4110 non-decode engine is also available to
be integrated with decode equipped OEM devices.
Note: The manufacturer of the end equipment must register with agencies
such as the Food and Drug Administration (FDA). The specifications
required for registration are not obtainable until the OEM manufacturer
uses the ScanQuest Engine in its final configuration. Therefore, it
becomes the responsibility of the manufacturer who incorporates the
scan engine into their product to comply with all federal laser safety
regulations. The manufacturer must submit a Laser Product Report for
the FDA in the US or similar forms as required by other countries.
Honeywell will assist its customers in complying with the necessary
procedures.
Theory of Operation
An object detection device is located behind the scanner window initiates the
scanning process. The detection device is active as long as the unit is being
powered. When the laser decodes a bar code, the scan engine transmits the
data to the host system.
If the same bar code stays in the field after successfully scanning, the laser stays
on for approximately four seconds and then turns off. This prevents unintentional
reads of the same bar code. To read the same symbol more than once, remove
the object from the scan field for approximately one second and then present the
symbol again.
If the bar code and object is removed from the field during the scanning process,
the laser turns off. In this stage, the scan engine’s computer remains on
“standby”.
However, if the object stays in the field, the laser remains on for up to
2.5 seconds trying to detect the bar code. To reactivate the scanning sequence,
remove the object.
The RS232 interface unit can be activated to scan by a command from the host.
When the unit is configured this way, the object detection is disabled
automatically.
2
INTRODUCTION
Accessories
The following are available:
IS4125 Decoded Scan Engine Part Numbers
PN DESCRIPTION MANUFACTURE/PART NO.
19-07092 Flex Ribbon 12 Pos x 70mm Burndy BFC12X70A4
M-07102 Thru Hole 12 Pos ZIF Connector Burndy FLWSLW125-1C7
M-07103 Flex Ribbon 12 Pos x 130mm Burndy BFC12X30A4
IS4110 Non-Decoded Scan Engine Part Numbers
PN DESCRIPTION MANUFACTURE/PART NO.
M-07104 Flex Ribbon 10 POS x 130mm Burndy BFC10X130A4
INTRODUCTION
Components of the ScanQuest Scan Engine
Figure 1: IS4110
Figure 2: IS4125
Scanner
window: This aperture emits laser light.
Object
Detection
Device:
When a specified time has elapsed without any scanning,
the unit will enter a “standby” mode. To reactivate the
unit, present an object in front of the window.
Ribbon Cables:
This IS4110 has a 10-position FFC/FPC cable and the
IS4125 has a 12-position FFC/FPC cable. Refer to
Scanner Termination starting on page 18.
3
INTRODUCTION
Label Locations
The serial number label is located on the bottom of the unit. On the top of the
unit is the “avoid exposure” and model number label.
The following are examples of these labels:
Figure 3: Labels
Maintenance
Smudges and dirt on the unit’s window can interfere with the unit’s performance.
If the window requires cleaning, use only a mild glass cleaner containing no
ammonia. When cleaning the window, spray the cleaner onto a lint free, non-
abrasive cleaning cloth then gently wipe the window clean.
4
5
AUTOMATIC SCAN ACTIVATION
An object detection device is located behind the scanner window initiates the
scanning process. In short range mode the signal projects approximately
101.61 mm – 177.84 mm (4" – 7") beyond the output window. In long range
mode the signal projects approximately 228.61 mm – 330.21 mm (9" – 13")
beyond the output window. The object detection device remains active as long
as the unit is powered.
When the unit remains dormant for a time, the laser will turn off. In this stage, the
scan engine’s computer is on “standby”. To reactivate the unit, present an object
within the scan field.
APPLICATIONS AND PROTOCOLS
The model number on each scan engine includes the scan engine number and
communications protocol.
Unit Communication Protocol(s) Type
IS4110 Laser Data Non-decode
IS4125-41
IS4125-76
RS232 and Light Pen Emulation
(Flash Upgradeable Firmware)
IS4125-47 Keyboard Wedge, Stand Alone Keyboard
(Flash Upgradeable Firmware)
IS4125-38 Low Speed USB
Keyboard Emulation or Serial Emulation Mode
Decode
Standard
IS4125-63 RS232 and Light Pen Emulation
(Flash Upgradeable Firmware)
IS4125-163 TTL, RS232
Decode
High-Density
6
DESIGN SPECIFICATIONS
OPERATIONAL
Light Source: VLD 650 ± 10 nm
CDRH/IEC: Designed to be used in CDRH Class II and
IEC Class 2 laser products
UL: UL recognized component for Canada and
US
Standard: 25 mm to 200 mm (1" to 8")
Depth of Field, UPC 100%
(0.33 mm (13 mil) bar codes): High Density: 10 mm to 175 mm (0.4" to 6.9")
Scan Speed: 52 scan lines per second minimum
Scan Pattern: Single scan line
Standard: 0.173 mm (6.8 mil)
Resolution: High Density: 0.132 mm (5.2 mil)
Roll, Pitch, Skew: 30°, 56°, 58° at 100 mm distance
Sweep Angle: 60°
Scan Width: 40 mm (1.57") @ Face; 280 mm (11.00") @
200 mm (8.00")
Print Contrast: 35% minimum reflectance difference
Decode Capability: All standard 1D symbologies including GS1
DataBar
IS4125
System Interfaces:
RS232C, Light Pen Emulation,
Keyboard Wedge, Low Speed USB,
RS232 TTL
MAINTENANCE
Window: Clean Periodically
Specifications are subject to change without notice.
Questo manuale è adatto per i seguenti modelli
6
Indice
Altri manuali Honeywell Motore
Honeywell
Honeywell Modutrol IV 71 Series Manuale operativo
Honeywell
Honeywell M9161V series Manuale operativo
Honeywell
Honeywell IS4910 Guida rapida alla configurazione
Honeywell
Honeywell Modutrol IV M6284A1089-S Manuale operativo
Honeywell
Honeywell BCS 7700 Series Manuale utente
Honeywell
Honeywell M7164 Manuale utente
Honeywell
Honeywell M7215 Manuale operativo
Honeywell
Honeywell Modutrol IV M7284 Manuale operativo
Honeywell
Honeywell N86 Series Manuale utente
Honeywell
Honeywell Modutrol IV M9175D 1014 Manuale utente
Honeywell
Honeywell Modutrol IV M934D Manuale operativo
Honeywell
Honeywell M9484 Manuale utente
Honeywell
Honeywell TFE731-5 Manuale utente
Honeywell
Honeywell Modutrol IV Motors Series 90 Manuale operativo
Honeywell
Honeywell Modutrol IV 72 Series Manuale operativo
Honeywell
Honeywell Modutrol IV M72 Series Manuale utente
Honeywell
Honeywell Modutrol IV Series 90 Manuale utente
Honeywell
Honeywell Modutrol IV Series 61 Manuale utente
Honeywell
Honeywell 46190153-501 Manuale utente
Honeywell
Honeywell IS220 Manuale utente
