Honeywell TrueEASE Manuale utente
M32930
33-00067EF-01
TrueEASE™ Humidification System
PROFESSIONAL INSTALLATION GUIDE
INCLUDED IN THIS HUMIDIFIER BOX
Tools needed to install humidier
Wire cutter/stripper
Tin snips or sheet metal cutter
#8 hex nut driver
Standard screwdriver
18-gauge wire (up to 5 conductor)
Other Requirements
If floor drain is not available, refer to Appendix C for
additional plumbing parts consideration.
If installed in or above a finished space, Honeywell
recommends installing a drip pan with water
sensor shut-off.
AHumidifier Bypass
Saddle valve
Water supply line
Drain hose (10 feet)
EOwner’s manual
FMounting template
GLow-Voltage SPST Manual Humidistat
Hardware (not pictured)
Additional accessories included in select
models
E
A
FG
GETTING
STARTED MOUNTING PLUMBING WIRING APPENDICES
OPERATION
AND SERVICE
Cross Reference Table
Humidier Honeywell® Aprilaire® GeneralAire®
HE100 and HE150 HE225 500 570
HE200 and HE250 HE265 600 900
HE300 HE365 700 1000
Humidier
NEED HELP? For assistance with this product please visit http://yourhome.honeywell.com
or call Honeywell Customer Care toll-free at 1-800-468-1502.
Read and save these instructions.
® U.S. Registered Trademark. Patents pending. Copyright © 2014 Honeywell International Inc. All rights reserved.
?
Humidier 33-00067EF—01
GETTING
STARTED MOUNTING PLUMBING WIRING APPENDICES
OPERATION
AND SERVICE
1
GETTING STARTED
Safety Denitions and Precautions .............. 2
What to Expect From Your Humidier ............ 3
Important Installation Requirements ............. 4
MOUNTING
Choosing a Mounting Method .................. 5
STEP ONE: Select the Mounting Location...... 6
STEP TWO: Install Mounting
Template to the Duct .................... 6
Bypass Model Installation ..................... 7
STEP THREE: Congure
Humidier Bypass ...................... 7
STEP FOUR: Installation ................... 8
STEP FIVE: Bypass Duct Installation ......... 9
PLUMBING
Water Supply and Drain Connections ........... 10
STEP ONE: Connect the Water Supply ....... 10
STEP TWO: Tap into a Water Line ........... 10
STEP THREE: Connect to the Water Drain .... 11
WIRING
Before Wiring Humidier ..................... 12
STEP ONE: Remove the Humidier Cover .... 12
STEP TWO: Install the Transformer
(Bypass Models Only).................. 12
STEP THREE: Wiring Humidier ............ 12
Installing the Humidistat ..................... 13
Duct Installation (H8908) ................13-14
Remote Installation (H8908)................ 14
Humidistat Wiring ......................15-17
Humidistat Checkout ..................... 18
Humidistat Operation ..................... 18
OPERATION AND SERVICE
Startup and Checkout ....................... 19
Routine Maintenance........................ 20
Troubleshooting ............................ 21
APPENDICES
A: Specications ........................... 22
B: Advanced Draining ....................... 23
C: Parts List .............................24-25
GETTING
STARTED
Safety Denitions and Precautions
Safety Denitions
These safety terms identify information you must read prior to installing or operating the humidier.
CAUTION: Indicates a hazardous situation which, if not avoided, could cause bodily injury
or property damage.
WARNING: Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Safety Precautions
Make sure you read and understand the following safety hazards before installing, using, or working with the
humidier:
CAUTION: Voltage Hazard.
Can cause electrical shock or equipment damage.
Disconnect HVAC equipment and any electrical outlet being used for the humidier installation.
WARNING: Electrocution and Water Hazard.
Can cause death, blindness, and water damage to the home and HVAC Equipment.
CAUTION: Condensation, Fire, and Freezing Water Hazard.
Can cause failure of fan or limit control or result in water damage to home.
Humidier 33-00067EF—01
2
GETTING
STARTED
The installer should review these points with the homeowner and answer any questions they have before leaving
the job site.
• Achieving Humidity Setpoint. It may take up to a week of continuous operation to achieve the humidity
setpoint, especially if the home is dry when the humidier is installed. This also depends on such factors as
weather, size of home, furnishings in the home, and insulation.
• Ideal Humidity. Home building industry experts cite 35% relative humidity as ideal for comfort and
safeguarding the home during the typical dry season. Homeowners can adjust to their own comfort or until
there is condensation on the windows. Lower the setpoint if condensation appears.
• Unit Not Humidifying. If the humidier is not running but the humidity is below the setpoint, the humidity
control may have a frost protection setting to prevent window condensation from appearing.
• Home Ventilation. Excessive ventilation sends moist air outside and replaces it with dry air. This can make it
hard to maintain the humidity setpoint. If installing a ventilator, use a solution that retains moisture. An Energy
Recovery Ventilator (ERV) is recommended.
• Cleaning Requirements. At least once per year it is recommended to change the humidier pad and clean
the water trays of the humidier. See Operation and Service section for details.
• Energy Consumption. It is important to explain that with any humidication solution there is a cost
associated with converting water to humidity. The humidier utilizes the air heat and air ow in your ducting to
make this conversion, which has gas and/or electric costs that depend on your HVAC system type and setup.
What to Expect From Your Humidier
Humidier 33-00067EF—01 3
GETTING
STARTED
Personal Safety
• Wear safety glasses while installing the humidier.
• Do not cut into any air conditioning or electrical line.
• Follow professional safety standards and all local regulations for plumbing, electrical, and mechanical
considerations.
Mounting Location
• Mount the humidier in a level position to avoid water damage and ensure maximum output.
• Location must have access to a water line, drain, and power.
• Do not install the humidier where the ambient temperature is lower than 34°F (1.1°C) or higher than 90°F
(40°C).
• Mounting area must be strong enough to support humidier weight (up to 16 lbs [Fan] or 10 lbs [Bypass]).
• Do not mount directly to ductboard.
• If used near a pool or spa, make sure the humidier can not fall into the water or be splashed.
• Ensure that the top and bottom covers of the humidier can be removed and that the pad is accessible from
the chosen location.
Water Supply and Drainage
• Consult local plumbing codes for drain size, material, and maximum temperature allowed.
If Replacing an Old Bypass Humidier
The humidier is not identical in size and shape to other Honeywell bypass humidiers. Before performing a
retrot installation, you might need to:
• Dry-t the humidier to the existing ducting, plumbing, and wiring before fastening it to the duct to ensure that
the existing connections will reach the humidier.
• If the duct opening of the old humidier is not the right size for the humidier, choose a new location or cover
the old opening with a piece of sheet metal and cut a new opening specically for the humidier using the
template provided.
Important Installation Requirements
Failure to comply with these requirements will result in voided warranty, improper installation, and
service callbacks.
Cross Reference Table
Humidier Honeywell® Aprilaire® GeneralAire®
HE100 and HE150 HE225 500 570
HE200 and HE250 HE265 600 900
HE300 HE365 700 1000
Humidier 33-00067EF—01
4
MOUNTING
Bypass:
Bypass humidiers use the pressure difference
between the supply and return to move duct
air through the humidier. Access to both the
supply and return are required. The bypass
humidier can be positioned on either the
supply or return duct.
MCR29871
Choosing a Mounting Method
Before beginning Mounting:
I have conrmed local codes for proper plumbing practices.
I have chosen an installation location that meets the requirements on page 4.
Humidier 33-00067EF—01 5
MOUNTING
STEP ONE: Select the Mounting Location
Choose a location that has access to a water supply
pipe. Cold or hot water can be used.
Select a vertical or horizontal surface on the HVAC
duct work, with adequate space clearances, where
the humidier can be mounted.
Ensure the location is near a drain. Consult local
plumbing codes for proper drainage. If no main
oor drain is available, see “Appendix C: Advanced
Draining.”
STEP TWO: Install Mounting Template to the Duct
Position the template on the duct.
• Make sure the template is level and in the desired
position on the duct. Peel adhesive backing
and press template rmly into place in desired
mounting location.
Ensure proper clearances from the air-conditioning
coil inside the duct.
NOTE: Bypass models extend into the duct 1/2 inch.
Ensure clearance inside the duct.
• For best performance, maintain at least 24 inches
downstream of open air space inside the duct.
Cut the sheet metal, following the template outline.
MCR29877
M29873
1
M29874
A-COIL
1-3/4
(44)
1/2
(13)
FAN
BYPASS
3
2
2
3
2
1
M32930
Humidier 33-00067EF—01
6
MOUNTING
STEP THREE: Congure Humidier Bypass
Congure the humidier bypass outlet to the side that
best ts the application.
If the bypass needs to be on the other side, remove
the top and bottom covers.
Unplug the damper wire and plug in on the other side
(HE150/HE250 only).
Pull the bypass clamps apart from center to remove
the bypass; snap it back into place with the outlet on
the desired side.
Ensure that the pad is accessible. The handle of the
pad holder and side panel of the humidier can be
switched so the pad holder can be removed (opposite
side of the bypass duct opening).
To remove the handle for the pad holder, slide it
toward the back of the humidier, then pull it away
from the humidier.
To remove the opposite side panel, place a
screwdriver into the two slots on the back of the
humidier, and pop the panel off.
Snap the pad holder handle and side panel back into
place in the desired conguration.
MCR29875
Bypass Model Installation
MCR29876
1
1
2
2
3
3
MCR29946
4
5
Humidier 33-00067EF—01 7
MOUNTING
STEP FOUR: Mounting
Secure the support hooks on Bypass models to the
bottom lip of the hole.
Push the top of the humidier back against the duct.
Verify the humidier is level and fasten the humidier
to the duct using two self-drilling sheet metal screws
provided.
MCR29870
2
1
Bypass Model Installation
Humidier 33-00067EF—01
8
Altri manuali per TrueEASE
2
Indice
Lingue:
Altri manuali Honeywell Umidificatore
Honeywell
Honeywell HWM845B Manuale utente
Honeywell
Honeywell TrueEASE HE100 Manuale utente
Honeywell
Honeywell HWM-255 Series Manuale utente
Honeywell
Honeywell enviracaire Elite HE225A Manuale utente
Honeywell
Honeywell HUL535B Manuale utente
Honeywell
Honeywell Enviracaire Elite HE365A Manuale utente
Honeywell
Honeywell HE360A - Whole House Powered Humidifier Manuale utente
Honeywell
Honeywell HCM-6009 - QuietCare Lon Console Humidifier Manuale utente
Honeywell
Honeywell HE120A Manuale utente
Honeywell
Honeywell HEV320 Series Manuale utente
Honeywell
Honeywell HM750 Manuale utente
Honeywell
Honeywell Enviracaire Elite HE365A Manuale utente
Honeywell
Honeywell enviracaire Elite HE225A Manuale utente
Honeywell
Honeywell HUL535BC Manuale utente
Honeywell
Honeywell TrueSTEAM Manuale utente
Honeywell
Honeywell TrueSTEAM HM512 Guida alla pianificazione
Honeywell
Honeywell DH835 Manuale utente
Honeywell
Honeywell TrueEASE HE100 Manuale utente
Honeywell
Honeywell HE260A Manuale utente
Honeywell
Honeywell TRADELINE HE360 Manuale utente
