Honeywell RCWL3501A Manuale utente
Installation
Instructions
RCWL35 Series
RCWL35N, RCWL3501A, RCWL3502A, RCWL3503A,
RCWL3504A, RCWL3505A, RCWL3506A
Decorative Wire Free Chimes and Push
69-2115EFS-05
69-2115EFS_C.indd 1 12/17/2007 2:23:55 PM
Installation Instructions
69-2115EFS—05 ii
Contents
Safety..........................................................2
Checking pack contents............................ 2
Open bell push...........................................3
Install the push battery..............................3
Open the chime.......................................... 3
Install the chime battery............................3
Test the kits................................................ 4
Volume control ...........................................5
Change tunes.............................................5
Add new push/reprogram..........................6
Unlearn procedure .....................................6
Recall function ...........................................6
Mount chime ..............................................7
Paint the wood cover.................................8
Specifications............................................. 9
Troubleshooting .........................................9
Disposal and recycling ............................12
Guarantee.................................................12
Declaration ...............................................13
69-2115EFS_C.indd 2 12/17/2007 2:23:55 PM
RCWL35 Series
1 69-2115EFS—05
ICON
WIRELESS CHIME BASE
DECORATIVE
CHIME COVERS
DECORATIVE CHIME COVERS
LED
VOLUME
CONTROL
TUNE BUTTON
PROGRAM
BUTTON
Compatible with décor wireless push, converter, motion detector, and door contact.
(Model No. RPWL30XXX series, and RCA901N and RCA902N.)
69-2115EFS_C.indd 1 12/17/2007 2:23:56 PM
Installation Instructions
69-2115EFS—05 2
Decorative Wire Free Chimes and Push
Checking Pack Contents
• Chime
• Bell push (for chime kit only)
• CR2032 battery for bell push (for
chime kit only)
• 2 x fixing screws for push (for chime
kit only)
• 2 x fixing screws for chime
• Wall plugs
• Adhesive pad (for chime kit only)
You will need:
• A Phillips screwdriver
• A small flat bladed screwdriver
• A 1/4-in. (6 mm) masonry drill
• 4 X LR14 ‘C’ Alkaline batteries
Safety
Before proceeding with the installation, please note the following safety warnings:
• Always follow the manufacturer’s advice when using power tools and wear
suitable protective equipment (e.g. safety goggles) when drilling holes, etc.
• Before drilling holes in walls, check for hidden electricity cables and water pipes.
The use of a cable/pipe locator is advisable if in doubt.
69-2115EFS_C.indd 2 12/17/2007 2:23:56 PM
RCWL35 Series
3 69-2115EFS—05
Installation
1. Open the bell push and insert the push battery
(CR2032).
2. Open the chime cover.
3. Insert chime batteries (LR14 C size).
69-2115EFS_C.indd 3 12/17/2007 2:23:56 PM
Installation Instructions
69-2115EFS—05 4
4. Operate push. Chime will play the default tune. First icon
will illuminate.
Note: The bell push (if supplied) is pre-
programmed to operate with the chime.
Installation
3 FT (1 M)
69-2115EFS_C.indd 4 12/17/2007 2:23:56 PM
RCWL35 Series
5 69-2115EFS—05
5. To adjust volume.
Installation
6. To change tunes
Press push button, chime will play tune, while
the icon on chime is flashing, press and release
tune button . Press and release button
again to cycle through the available tunes
until you hear the tune you want. The last
tune played will be stored after the icon stops
flashing. To confirm, press the push button and
chime will play the tune you want.
69-2115EFS_C.indd 5 12/17/2007 2:23:56 PM
Installation Instructions
69-2115EFS—05 6
7. To add new push/reprogram
Press and hold the program button l. The icons will illuminate
in sequence. Release the program button when icon you
choose is illuminated. Operate your new push and the chime
will play tune, icon will flash. To change tune, refer to step 6.
8. Unlearn procedure
To remove a push from the chime’s memory, press and hold the
program button l. Each icon will light in turn. When the icon
associated with the push to be un-learned is lit, release the button. Then press
and hold down both land buttons, until a ‘beep’ sound is heard.
9. Recall function
A short push of the program button lwill flash the icon that was last in use.
Installation
69-2115EFS_C.indd 6 12/17/2007 2:23:56 PM
RCWL35 Series
7 69-2115EFS—05
10. Mount the bell push
Install back cover to wall, use screws provided/adhesive
pad. Close the cover.
Note: Before final installation adjust distance and position
between push and chime to optimize the chime within your
environment. Dense walls and metal can reduce range.
TOP
Installation
Wall Type Range Reduction
Dry-lined partition wall 10–30%
Single-layer brick wall 20–40%
Double-layer brick wall 30–70%
Metal panel/radiator 90–100%
69-2115EFS_C.indd 7 12/17/2007 2:23:56 PM
Installation Instructions
69-2115EFS—05 8
12. For stainable covers only
Choose your paint, stain or varnish and then
apply to the cover. Follow manufacturers’ advice
on the paint/vanish. It is possible to unscrew
the four screws shown below for painting.
Ensure you screw it back with the same screws
provided!
Once completed, clip it onto the base as in step 11.
Installation
11. Mount the chime
Mounting holes are marked with
screw symbol. Clip on the front
cover.
69-2115EFS_C.indd 8 12/17/2007 2:23:56 PM
Questo manuale è adatto per i seguenti modelli
11
Indice
Lingue:
Altri manuali Honeywell Sistema di interfono
Honeywell
Honeywell DC313 FB Series Manuale utente
Honeywell
Honeywell RCWL105A Manuale utente
Honeywell
Honeywell IS-6520S-GE Manuale utente
Honeywell
Honeywell DC515 Series Manuale utente
Honeywell
Honeywell KMA 28B Guida utente
Honeywell
Honeywell 311 Series Manuale utente
Honeywell
Honeywell RCWL330A Manuale utente
Honeywell
Honeywell VisioCam RCWL8000A Manuale utente
Honeywell
Honeywell DCR311 Series Manuale utente
Honeywell
Honeywell DC315 P2/BS Series Manuale utente
