Honeywell PRO32E1PS Manuale di istruzioni

Power Supply Assembly and Installation Instructions

1 of 12

1 Overview

The PRO32E1PS and PW6K2E2PS power supply and battery charger is compatible with the PW3000,

PW5000, PW6000, PRO2200, and PRO3200 systems. For ordering purposes please use the PW6K2E2PS

for the PW3000, PW5000, and PW6000 systems and PRO32E1PS for PRO2200, and PRO3200 systems.

This power supply will convert AC input voltage into a 13.8VDC output with 4.0 amps maximum of

continuous current. The power supply accepts an input voltage of 85VAC to 265VAC at 50Hz/60Hz. The

power supply provides AC fail and low battery supervision when connected to PW3000, PW5000,

PW6000, PRO2200, and PRO3200 I/O PFL (Power Fail) and auxiliary inputs.

2 Specifications

• 4.0 amp maximum continuous output current at 13.8VDC with overload protection.

• Filtered and electronically regulated outputs.

• Built-in charger for sealed lead acid batteries with a maximum charge current of 250mA.

• Automatic switch over to stand-by battery, if present, upon AC power failure.

• Reverse battery polarity with a non-replaceable fuse.

• Low battery supervision when connected to a low battery input on the panel.

• AC fail supervision when connected to PWR fail on panel.

• Short circuit/overload/overvoltage protection.

• 0° C to 49° C operating temperature range.

• UL 60950 listed.

• CE compliant.

Warning

• Power Supply shall be installed in accordance with the National Electric Code, as

well as all applicable local regulations.

• Before installation, turn off the extra circuit breaker that supplies power to the

system. Do not re-apply power until installation is complete.

• To reduce the risk of electric shock, do not expose the unit to rain, liquids, or

excessive moisture.

2 of 12

List of Contents

Document 800-08279, Revision A

February 2011

• No user-serviceable parts. Installation and servicing should only be performed by

qualified personnel.

• Route all power-limited (low voltage) wiring at least 1/4” (6.35 mm) away from any

non-power limited wiring. NOTE: The wires going from the battery to the power supply are

non-power-limited. All the wires that go from the power supply to the other components in the

enclosure (except the battery) are power-limited.

• Backup battery 12V, 7 AH sealed lead-acid maintenance-free battery, 712BNP or

equivalent.

3 List of Contents

• Power Supply Assembly (1)

• Cable Assembly 12VDC Power and Battery connections (1)

• Cable Assembly AC and Battery Fail connections (1)

• Cable Assembly AC Power Inlet and LED Power Indicator (1)

• Cable Assembly Ground Plate to Chassis (1)

• Power Supply Mounting Plate (4 keyholes) (1)

• Machine Screw 8-32x5/16” Ground Wire to Plate (1)

• Kep Nut 8-32 Ground Wire to Plate (1)

• Machine Screw M3x0.5, 6mm Power Supply to Mounting Plate (4)

• Installation Instructions (1)

• IEC Power Cord (1)

4 Cable Assembly Connections

The power supply has three pin connectors (CN1, CN2, and CN3) to which you need to connect three

cable assemblies, as shown below:

Figure 1: Power Supply Pin Connectors

CN1 CN2

CN3

3 Pin Connectors

3 of 12

Cable Assembly Connections

Document 800-08279, Revision A

February 2011

Here are the three cable assemblies that connect to these pin connectors:

Figure 2: AC Power Inlet and LED Indicator Cable Assembly

Figure 3: 12VDC Power and Battery Cable Assembly

Connects to

CN1

LED

AC Power Inlet

Connects to

CN2

4 of 12

Cable Assembly Connections

Document 800-08279, Revision A

February 2011

Figure 4: AC and Battery Fail Cable Assembly

After connecting the three cable assemblies to the pin connectors CN1, CN2, and CN3, the fully

connected power supply should look like the below photo (Figure 5 on page 5) when viewed from the

front, inside the metal cabinet:

Connects to

CN3

5 of 12

Installation Instructions

Document 800-08279, Revision A

February 2011

Figure 5: Fully Connected Power Supply, Front View

5 Installation Instructions

1. Use this power supply only with Honeywell PW3000, PW5000, PW6000, PRO2200, and

PRO3200 series access control and proprietary alarm units.

2. Secure enclosure in the desired location, using appropriately sized fasteners.

3. Unpack the power supply and metal plate. Do not discard the packing materials until installation

and checkout are successfully completed.

4. Remove metal plate from packaging.

6 of 12

Installation Instructions

Document 800-08279, Revision A

February 2011

5. Turn the power supply over on its backside and install the four mounting screws (that come with

the kit) only a few turns in.

6. Position the power supply over the 4 keyholes on the metal plate making sure that the round hole

(see the below figure) is in the bottom left corner as shown and the power supply is positioned

with the AC input terminals (CN1) facing downward.

7. Slide the power supply down in the keyholes until they bottom out. Then, tighten the four

mounting screws to secure the power supply to the metal plate.

AC Input

Connector

CN1

Round Hole

7 of 12

Installation Instructions

Document 800-08279, Revision A

February 2011

8. Using the provided #8x32 screw and locknut, secure the provided ground wire (GREEN with

YELLOW stripe) to the back of the metal plate as shown below:

9. Take the input power cord with LED and insert the LED into the panel enclosure as shown below.

Note: LED MUST be installed BEFORE the power inlet.

10. Once the LED is installed and fully seated, install the AC power inlet into the panel. See the photo

below:.

LED

Power

Inlet

8 of 12

Installation Instructions

Document 800-08279, Revision A

February 2011

11. Connect the AC power inlet and LED indicator cable to the power supply by pushing and inserting

the cable connector to the pin connector CN1:

Figure 6: AC Power Inlet and LED Indicator Cable Assembly Connecting to CN1 Pin Connector

Warning: Do not connect power at this time!

12. Connect the 12VDC output and battery output cable to the power supply by pushing and inserting

the cable connector to the pin connector CN2:

Figure 7: 12VDC Power and Battery Cable Assembly Connecting to CN2 Pin Connector

AC Power Inlet and LED Indicator

Cable connecting to CN1

CN1 Pin

Connector

12VDC Power and Battery Cable

Connecting to CN2

CN2 Pin

Connector

9 of 12

Installation Instructions

Document 800-08279, Revision A

February 2011

13. Connect the AC and battery fail cable to the power supply by pushing and inserting the cable

connector to the pin connector CN3:

This is how the pin connectors CN2 and CN3 should look like after attaching both cables:

AC and Battery Fail Cable

Connecting to CN3

CN3

Connector

CN2 and CN3 connected

CN3

CN2

10 of 12

Installation Instructions

Document 800-08279, Revision A

February 2011

14. Slide the power supply and metal plate assembly into the metal enclosure, noting the orientation of

the ground wire towards you:

15. Secure the ground wires (GREEN with YELLOW stripe) from the mounting plate and AC Power

Inlet Cable to one of the grounding lugs inside the mounting enclosure, as shown on the left.

16. Connect the 12VDC power output from the power supply to the controller input, noting proper

polarity.

17. Connect the battery leads to an appropriately-sized battery for the application.

18. Connect the low battery wires to the appropriate panel input.

19. Connect the AC power fail wires to the appropriate panel input.

20. Connect the supplied power cable into the power inlet on the outside of the enclosure.

21. Check all power supply wiring to ensure it is installed properly.

22. Power on the system by plugging the supply AC power cord into the appropriate AC source.

23. Check to make sure that your system is powered up correctly.

24. Check to make sure that the red LED located near the AC power inlet is illuminated.

25. Route all power-limited wiring at least 0.25” (6.35 mm) away from any non-power-limited wiring.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Honeywell Alimentazione elettrica

Honeywell

Honeywell HP600ULM Manuale utente

Honeywell

Honeywell PS1202C Manuale utente

Honeywell

Honeywell HPL624 Manuale tecnico

Honeywell

Honeywell HP1205UL-4 Manuale tecnico

Honeywell

Honeywell HP312CX Manuale utente

Honeywell

Honeywell HPF24S8 Manuale tecnico

Honeywell

Honeywell HPR12DC416UL Manuale tecnico

Honeywell

Honeywell HPTV2416UL Manuale tecnico

Honeywell

Honeywell HP400ULM Manuale tecnico

Honeywell

Honeywell PS1202A00 Manuale utente

Honeywell

Honeywell HP24100ULWP Manuale utente

Honeywell

Honeywell Gamewell FCI GFPS-9 Manuale utente

Honeywell

Honeywell GENT VCS-PSU-N Manuale utente

Honeywell

Honeywell VX89301PWRSPLY Manuale utente

Honeywell

Honeywell HLSPS25-XPH Manuale utente

Honeywell

Honeywell Fire-Lite FL-PS6 Manuale utente

Honeywell

Honeywell HPF24S6 Manuale utente

Honeywell

Honeywell NOTIFIER APS2-6R/E Manuale utente

Honeywell

Honeywell SILENT KNIGHT SK-PS6 Manuale utente

Honeywell

Honeywell HP300ULX Manuale tecnico

Honeywell

Honeywell PRO-2200 Manuale utente

Honeywell

Honeywell PEHA D 942 SPV Manuale utente

Honeywell

Honeywell HP24100WP Manuale tecnico

Honeywell

Honeywell NOTIFIER FCPS-24S6 Manuale utente

Manuali Alimentazione elettrica popolari di altre marche

Monacor

Monacor PS-12CCD Manuale utente

VOLTIMA

VOLTIMA MagicBox 15 Manuale utente

Agilent Technologies

Agilent Technologies 6032A Manuale utente

Miller

Miller Auto Deltaweld 452 Manuale utente

BCP

BCP PUOUBK Foglio di istruzioni

HC 2210 Manuale utente

Puls

Puls CT5.241 Manuale utente

OCZ

OCZ ZX1250W Manuale utente

iseg

iseg ECH 238 Manuale utente

Power

Power XXL A Series Manuale utente

Agilent Technologies

Agilent Technologies 6631B Manuale utente

Renogy

Renogy PHOENIX 300 Manuale utente

HP 6200B Manuale di servizio

Epson

Epson Stylus Scan 2500 Manuale operativo

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuale utente

Puls

Puls MiniLine ML50.100 Manuale utente

Puls

Puls AS-Interface SLA4.100 Manuale utente

Kenwood

Kenwood PS-60 Manuale utente