Honeywell 2070A - 43 Cubic Foot Expandable Anti-Theft Wall... Come usare

Operation & Installation Guide

Model 2070A / 2070AE

Read These Instructions Very Carefully!

Limited Warranty

Home and Ofﬁce Security Safes

MHAS2070AE0907

ENGLISH

If your Honeywell safe fails to operate because of a manufacturing defect any time up to ﬁve (5)

years from the date of original purchase, we will, at our discretion, repair or replace the unit at no

charge to the original owner. A copy of your sales receipt is required as Proof of Purchase.

The consumer must ﬁrst contact SISCO® Customer Service (800-223-8566, USA and Canada;

310-638-1182 outside of USA and Canada, or via E-mail at [email protected])

during the Term of the Limited Warranty for authorization on the repair or replacement of the safe.

For the repair of the safe, SISCO Customer Service may provide approval for taking it to a local

locksmith. For the replacement of the safe, the consumer must return it, prepaid, to SISCO

(2835 E. Ana St., Rancho Dominguez, CA 90221). SISCO will replace the safe with a comparable

model, shipping prepaid.

WHAT IS NOT COVERED

SISCO’s responsibility and the consumer’s rights are limited to the repair or replacement of the

defective safe, as stated above.

This Warranty does not apply if the product has been damaged by improper installation, neglect,

accident, misuse, exposure to extremes of heat or humidity, terrorism, war, acts of God, or as a

result of service or modiﬁcation by other than an authorized service center. While your SISCO safe is

warranted to be free of mechanical defect during the Term of Limited Warranty, the Warranty does

not apply to the ﬁnish of the safe.

SISCO is not responsible for any costs associated with removing or installing this product.

SISCO is not responsible for damage or loss of the contents of the safe nor for the unauthorized

removal of contents.

SISCO is not responsible for any damages incurred to the safe during shipment.

This Limited Warranty applies only to new SISCO safes, purchased by the original owner, and is not

transferable to second owners or “factory seconds” safes purchased by the consumer.

No implied Warranty of salability or ﬁtness exists other than those descriptions provided on the

packaging, instructions and advertising. No other covenants or warranties, either implied or stated,

written or oral, are hereby present. Some states do not allow limitations on how long an implied

Warranty lasts, so the above limitations may not apply to you.

This Warranty gives you speciﬁc rights and you may also have other rights which vary from state to

state.

The Honeywell trademark for Home/Ofﬁce Safes is used with permission. Honeywell Safes are

distributed exclusively by SISCO. Honeywell makes no representations or warranties with respect to

this product or service. The Honeywell Trademark is used under license from Honeywell Intellectual

Properties Inc. by SISCO.

Safe Identiﬁcation Record

Home and Ofﬁce Security Safes

For Your Protection

• Do not remove the Serial Number tag from the safe.

• Store Emergency Override Keys away from (NEVER INSIDE) safe.

• Record all Safe Identiﬁcation Numbers on Safe Identiﬁcation

Record (last page).

• Save this manual and NEVER keep it inside the safe.

Index

Overview of Your Safe ...................................

Opening Safe For The First Time................

Installing Your Wall Safe................................

Programming a Personal Passcode ...........

Using the Emergency

Override Key.....................................................

Checking, Changing and Installing

New Batteries...................................................

Use, Care and Maintenance ........................

Customer Support ..........................................

Page 1

Page 2

Page 3

Page 6

Page 7

Page 8

Page 9

Page 10

Index

Model Number

Serial Number

Key Number

Digital Passcode Record

Your Passcode must be at least 3 digits and no more than 8 digits followed

by the letter A.

Important:

Once your personal Passcode is programmed, the factory pre-set code will no

longer open the safe.

Overview of Your Safe

WELCOME!

Your new Honeywell Digital Anti-Theft Wall Safe will provide years of safe

and secure protection for your valuables, important documents and other

personal items. All Honeywell safes are designed and built using the highest

manufacturing standards to ensure maximum user satisfaction under a variety

of conditions. With proper care, your Honeywell safe will provide “Peace of

Mind” for many years to come.

Thank you and Enjoy!

The following list outlines the items and quantities of each included with

your new safe. Please carefully check the list to conﬁrm all items have been

received. If any item is missing, then please contact Customer Service

@ 1-800-223-8566.

(A) Operation & Installation Guide 1 ea.

(B) Emergency Override Key 2 ea.

(D) Removable Shelf Extensions 7 ea.

(E) Pre-installed “AA” Batteries 4 ea.

Home and Ofﬁce Security Safes

Important: DO NOT RETURN SAFE TO STORE

If you are missing parts, have difﬁculty programming your safe or

have any other questions pertaining to its proper use and care, DO

NOT RETURN your safe to the store. Please contact Customer Service

at 1-800-223-8566 (USA & Canada) for assistance.

Notes

A E

Opening Safe For The First Time

Home and Ofﬁce Security Safes

Opening Your Safe for the First Time Using

the Pre-set Factory Code.

Batteries have been pre- installed at the factory. Using the

factory pre-set Passcode 159A, open the safe as follows:

1. Enter the three digit number 159 on the keypad followed

by the letter A. If entered correctly, the green LED will light

and the lock will click.

2. Pull the handle open within 5 seconds and open

the door.

3. A red LED indicates that the Passcode was entered

incorrectly. Re-enter the code and try again.

Security Lockout:

The safe is designed to lock out the keypad if the wrong Passcode is entered

multiple times.

• After the 3rd error: 20 second lock-out. (waiting period)

• 4-6 errors: 5 minute lock-out.

• 7+ errors: 1 hour lock-out.

If you have forgotten the Passcode, entry can be made using the Emergency

Override Key. (See page 7).

Important:

If no action is taken, the safe will automatically relock in 5 seconds and the code

will need to be re-entered.

Closing Your Safe

1. Make sure nothing inside the safe is obstructing the door from completely

closing.

2. Close the safe door and press the handle into the locked position.

Important:

This safe is equipped with an interior light. The control switch is located on the

inside door panel. When closing the safe it is important that the light switch be

turned to the off position. Failure to do so will drain the batteries of power and

the safe will not open when the digital key pad is used.

Anti-Theft safe

Customer Support

How to Contact Us

Phone: 1-800-223-8566 (USA and Canada)

Monday through Friday, 7:30 am to 4:30 pm Paciﬁc Standard Time

Email: CustomerSer[email protected]

In addition to the required information regarding your safe, you must include the

best time and proper telephone number to reach you during our normal Customer

Service hours.

Mail: Attn: Customer Service Dept.

SISCO

2835 E. Ana Street

Rancho Dominguez, CA 90221

Internet: www.HoneywellSafes.com

Ordering Replacement Keys

If a key becomes misplaced or you would like additional keys, you may conveniently

purchase them from our Customer Service department. You must supply the following

information to assure accurate processing:

• Name / Address / Telephone

• Safe Model Number / Serial Number

• Key Number (located on the key and Emergency Override Key lock cover)

• Number of keys requested

• E-mail address if available

AUSTRALIA

Mail:

Customer Service Dept.

Master Distributors

11 Howleys Rd.

Notting Hill VIC 3168

03-9538-9200

EUROPE

Mail:

Freightways Distriservices B.V.

P.O. Box 3077

2220 CB Katwij

The Netherlands

+31(0) 71.409.0721

Payment and Delivery

In the USA, replacement keys are available for a fee and credit card orders are accepted

by telephone or via our web site. Checks or Money Orders are required for orders

received by mail and should be made payable to SISCO®. Contact our Customer

Service department for costing information prior to ordering.

Yellow

Light

Red

Light

Green

Light

Red

Light

10 3

Home and Ofﬁce Security Safes

Installing Your Wall Safe

Location

Your Honeywell Wall Safe should be mounted in an obscure location such as a

bedroom or hall closet and must be installed in a 2’ x 4’ or thicker framed wall. Be

sure that no plumbing pipes or electrical wires run through the wall cutout area

where your wall safe is to be located and that there is room to swing the safe door

open without obstruction. The Wall Safe is 14 inches wide and designed to ﬁt

between standard 16 inch center-to-center wall framing.

Note: Most homes have wall framing construction of 2 x 4’s and/or 2 x 6’s that are

located on 16-inch centers.

Tools Required for Installation

• Tape measure

• Pencil

• Drill

• Jig saw or equivalent

• Building square

• Phillips screwdriver

• Flashlight

NOTE: Instructions shown are for wood framed wall installation.

Installation for aluminum or steel stud walls may require pre-drilling and/or

alternative mounting screws.

Customer Support

Your Safe’s Unique Identiﬁcation Numbers

When contacting Customer Service, you should be prepared to supply some

important information that speciﬁcally identiﬁes your safe. This information is

extremely important to assuring prompt and accurate customer assistance.

It is strongly recommended that you identify and record the following information

in the “Safe Identiﬁcation Record” form located on the inside back cover of this

manual:

Model Number

Serial Number

Key Number

Locating Model and Serial Numbers

Most Honeywell safes include a small metallic silver or gray tag afﬁxed to one

of the surfaces. This tag is usually located on the front or right side of the safe.

This tag contains the Serial Number, and on selected models a similar tag is

attached containing the Model Number. If a Model Number tag is not attached

to the safe, then it can be located on the front or side panel of the box that the

safe was packaged in. Write this number down for future reference.

Key Number

The Key Number is located on the key. If you do not have the key, the number

is also located on a sticker on the inside of the Emergency Override Key lock

cover. (See Emergency Override Key, page 6)

Important: DO NOT REMOVE TAGS!

In case your safe becomes inoperable or you lose your keys, these identiﬁcation

numbers will be needed to correct the problem. It is recommended that the

number tags remain in place on the safe. If removal is necessary, then they

should be attached to the inside back cover of the Operation and Installation

Guide. Store in a safe and secure place for future reference.

Home and Ofﬁce Security Safes

Installing Your Wall Safe

STEP 1- Wall Cutout

1. Determine the approximate location of the stud for the right hand side of your

Wall Safe (hinge side). Drill or cut a large enough pilot hole to determine

where the inside edge of this stud is located.

2. Using a building square, draw a vertical pencil line 21 1/8 inches long along

the inside edge of the stud. This will locate the right hand (hinged) side of

the safe.

3. From the top of your scribed line, measure 14 inches to the left and make a

pencil mark. Repeat this measurement at the bottom of the vertical line. With

the building square, draw a vertical line between the pencil marks locating the

left side of the safe.

4. With the square, draw a horizontal line at the top of the 21 1/8 inch

measurement joining the two vertical lines. Repeat this action at the bottom.

You should now have a 14 inch x 21 1/8 inch rectangle scribed on the wall

between studs.

5. Using a jig saw or equivalent tool and starting at the pilot hole, cut along the

pencil lines and remove the wall section.

Use, Care and Maintenance

Safe Care and Maintenance

When properly maintained, your safe will continue to operate and accurately

read the authorized Passcode for many years. In order to ensure optimum

performance of your safe, please follow these simple precautions:

Replace Batteries – For best results and performance, we recommend that the

batteries be replaced at least once a year or sooner depending on amount of

use.

Clean Hands - Never attempt to operate the digital keypad if your hands have

excessive dirt, debris or liquids on them.

Clean Safe – To clean the surface of your safe, it is recommended that you

use a mild cleaner (i.e., window cleaner) to avoid scratching or discoloring the

surface. Always wipe dry and NEVER use abrasive cleansers on the safe or

digital keypad.

For future reference, store this Operation and Installation Guide in a secure area

away from the safe. DO NOT DISCARD!

Caution:

With a ﬂashlight, look through the pilot hole and make sure there are

no electrical wires or plumbing in the cutout area before you start

cutting.

Home and Ofﬁce Security Safes

Step 2 - Install Safe

Once safe has been placed into position in the wall cutout,

secure into place by screwing 4 wood screws (included) through

the four recessed holes in the front ﬂange of Safe and into studs.

Tighten screws ﬂush with ﬂange.

3. Select the expandable shelf extensions that will work best with

the depth of the installed safe and using small screws and nuts,

secure into place.

1. Install your wall safe into the wall cutout so that the hinge side of the safe is

ﬂush against the right hand stud and the front ﬂange is ﬂat against the wall.

With the safe door open, extend the telescoping back by pushing it from

the inside until maximum possible depth is achieved. Once the back is

extended, install six wood screws (included) through the pre-drilled holes in

right hand side of safe and into stud. Tighten safe ﬂush to stud. Do not over

tighten screws.

2. Now install six screws (included) through the pre-drilled holes in left hand side

of safe and into stud. Do not over tighten.

NOTE: There may be a slight amount of space between the safe side wall

and the left hand stud, this is normal. The right hand hinged side of your wall

safe must be tightened ﬂush to the right hand stud.

Checking, Changing and Installing

New Batteries

Your new safe arrived with 4-AA batteries pre-installed at the factory. It is important

to periodically check the batteries and, if necessary, replace with a new set.

Checking Batteries

1. Locate the B key on the keypad and press.

2. If the yellow LED ﬂashes and you hear a beep, the batteries

are good.

3. If the red LED ﬂashes, change the batteries within two

months.

4. If the LED does not light, then you must replace the

batteries immediately.

5. Proceed to Changing and Installing New Batteries.

Changing and Installing New Batteries

1. Using your personal Passcode or Emergency Override

Key, open the safe door and locate the battery

compartment on the back of the door.

2. Press ﬁrmly in on the right side of the battery compartment

cover and slide to the left to open.

3. Remove the 4 old batteries and replace with 4 new

Alkaline “AA” batteries. Make sure that they are installed

in the proper direction as illustrated on the battery

compartment interior.

4. Replace the cover and, prior to closing, test your

Passcode as instructed on page 6.

NOTE: Proper disposal of discharged batteries is encouraged!

Important:

Replacing the batteries will not erase your personal Passcode from memory. However,

weak or dead batteries will prevent the use of the digital key pad. Access to the safe

will have to be made using the Emergency Override Key. (See page 7).

Installing Your Wall Safe

Yellow

Light

Red

Light

Battery

Cover

Home and Ofﬁce Security Safes

Using the Emergency

Override Key

Using the Emergency Override Key

Your safe is equipped with an Emergency Override Key which

allows immediate access in case you forget your Passcode or the

batteries need replacing.

1. Remove the key lock cover located beneath

the digital keypad.

2. Insert one of the Emergency Override keys (2 included) into

the bypass lock and turn to the left.

3. Pull the handle up and pull open the safe door.

4. After re-programming (See page 6) or changing batteries

(See page 8), replace the key lock cover and store keys in a

safe and secure location away from the safe.

Programming a

Personal Passcode

For security reasons, it is very important that you program your own personal

Passcode into the digital lock. The factory Passcode 159A should be changed

immediately.

Programming Your Personal Passcode

1. Using the factory assigned Passcode (159A), open the safe.

(See page 2).

2. Locate and then press and release the small red memory

button located inside the safe on the edge of the lock

cover. The keypad will beep twice and the yellow LED will

light.

3. Select a Passcode using 3 to 8 numbers (no letters) and

enter it on the keypad.

4. After entering the numbers, press the B key. The keypad

will again beep twice and the yellow LED will light. This

will complete the programming of your personal Passcode.

Leave the door open and proceed to Testing Your New

Passcode.

Testing Your New Passcode

1. With the door in the open position, push the lock handle

into the closed position. In about 3 seconds, the safe will

automatically lock.

2. Enter your new personal Passcode onto the keypad followed

by the letter A and the digital lock should click open.

Example:

3. Pull the handle and open the safe.

4. If the new Passcode does not unlock the safe, then repeat

the steps to program your personal Passcode and retest.

Once programming is completed, write your personal Passcode

down and store it in a safe and secure place away from the safe. The

factory pre-set Passcode will no longer open your safe.

Important:

Your new Passcode will always consist of your selected number code followed by the

letter A.

Yellow

Light

Anti-Theft safe

Memory

Button

Home and Ofﬁce Security Safes

Using the Emergency

Override Key

Using the Emergency Override Key

Your safe is equipped with an Emergency Override Key which

allows immediate access in case you forget your Passcode or the

batteries need replacing.

1. Remove the key lock cover located beneath

the digital keypad.

2. Insert one of the Emergency Override keys (2 included) into

the bypass lock and turn to the left.

3. Pull the handle up and pull open the safe door.

4. After re-programming (See page 6) or changing batteries

(See page 8), replace the key lock cover and store keys in a

safe and secure location away from the safe.

Programming a

Personal Passcode

For security reasons, it is very important that you program your own personal

Passcode into the digital lock. The factory Passcode 159A should be changed

immediately.

Programming Your Personal Passcode

1. Using the factory assigned Passcode (159A), open the safe.

(See page 2).

2. Locate and then press and release the small red memory

button located inside the safe on the edge of the lock

cover. The keypad will beep twice and the yellow LED will

light.

3. Select a Passcode using 3 to 8 numbers (no letters) and

enter it on the keypad.

4. After entering the numbers, press the B key. The keypad

will again beep twice and the yellow LED will light. This

will complete the programming of your personal Passcode.

Leave the door open and proceed to Testing Your New

Passcode.

Testing Your New Passcode

1. With the door in the open position, push the lock handle

into the closed position. In about 3 seconds, the safe will

automatically lock.

2. Enter your new personal Passcode onto the keypad followed

by the letter A and the digital lock should click open.

Example:

3. Pull the handle and open the safe.

4. If the new Passcode does not unlock the safe, then repeat

the steps to program your personal Passcode and retest.

Once programming is completed, write your personal Passcode

down and store it in a safe and secure place away from the safe. The

factory pre-set Passcode will no longer open your safe.

Important:

Your new Passcode will always consist of your selected number code followed by the

letter A.

Yellow

Light

Anti-Theft safe

Memory

Button

Home and Ofﬁce Security Safes

Step 2 - Install Safe

Once safe has been placed into position in the wall cutout,

secure into place by screwing 4 wood screws (included) through

the four recessed holes in the front ﬂange of Safe and into studs.

Tighten screws ﬂush with ﬂange.

3. Select the expandable shelf extensions that will work best with

the depth of the installed safe and using small screws and nuts,

secure into place.

1. Install your wall safe into the wall cutout so that the hinge side of the safe is

ﬂush against the right hand stud and the front ﬂange is ﬂat against the wall.

With the safe door open, extend the telescoping back by pushing it from

the inside until maximum possible depth is achieved. Once the back is

extended, install six wood screws (included) through the pre-drilled holes in

right hand side of safe and into stud. Tighten safe ﬂush to stud. Do not over

tighten screws.

2. Now install six screws (included) through the pre-drilled holes in left hand side

of safe and into stud. Do not over tighten.

NOTE: There may be a slight amount of space between the safe side wall

and the left hand stud, this is normal. The right hand hinged side of your wall

safe must be tightened ﬂush to the right hand stud.

Checking, Changing and Installing

New Batteries

Your new safe arrived with 4-AA batteries pre-installed at the factory. It is important

to periodically check the batteries and, if necessary, replace with a new set.

Checking Batteries

1. Locate the B key on the keypad and press.

2. If the yellow LED ﬂashes and you hear a beep, the batteries

are good.

3. If the red LED ﬂashes, change the batteries within two

months.

4. If the LED does not light, then you must replace the

batteries immediately.

5. Proceed to Changing and Installing New Batteries.

Changing and Installing New Batteries

1. Using your personal Passcode or Emergency Override

Key, open the safe door and locate the battery

compartment on the back of the door.

2. Press ﬁrmly in on the right side of the battery compartment

cover and slide to the left to open.

3. Remove the 4 old batteries and replace with 4 new

Alkaline “AA” batteries. Make sure that they are installed

in the proper direction as illustrated on the battery

compartment interior.

4. Replace the cover and, prior to closing, test your

Passcode as instructed on page 6.

NOTE: Proper disposal of discharged batteries is encouraged!

Important:

Replacing the batteries will not erase your personal Passcode from memory. However,

weak or dead batteries will prevent the use of the digital key pad. Access to the safe

will have to be made using the Emergency Override Key. (See page 7).

Installing Your Wall Safe

Yellow

Light

Red

Light

Battery

Cover

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Honeywell Sicuro

Honeywell

Honeywell 5113 Manuale utente

Honeywell

Honeywell 2208 Manuale utente

Honeywell

Honeywell 2101 Manuale utente

Honeywell

Honeywell Media Protector 2040 Manuale utente

Honeywell

Honeywell 5911 Manuale utente

Honeywell

Honeywell 5103 Manuale utente

Honeywell

Honeywell 1114 Manuale utente

Honeywell

Honeywell 5805 Manuale utente

Honeywell

Honeywell 2605 Manuale utente

Honeywell

Honeywell 2111 Manuale utente

Honeywell

Honeywell 5605 Manuale utente

Honeywell

Honeywell 2077D - 1.21 Cubic Foot Anti-Theft Safe Come usare

Honeywell

Honeywell 5101 Manuale utente

Honeywell

Honeywell 1532 Manuale utente

Honeywell

Honeywell 1553 Manuale utente

Honeywell

Honeywell 2605 Come usare

Honeywell

Honeywell 3518 Manuale utente

Honeywell

Honeywell 5203 Manuale utente

Honeywell

Honeywell 5912 Come usare

Honeywell

Honeywell 2077D - 1.21 Cubic Foot Anti-Theft Safe Manuale utente

Honeywell

Honeywell 2092D - Waterproof Fire Safe Come usare

Honeywell

Honeywell 5005B Manuale utente

Honeywell

Honeywell 1502 Manuale utente

Honeywell

Honeywell 5101 Manuale utente

Manuali Sicuro popolari di altre marche

Squire

Squire Stronghold Keysafe Manuale utente

Phoenix

Phoenix FS0352C Scheda informativa del prodotto

Phoenix

Phoenix KS0030E Series Manuale utente

Vaultek

Vaultek 10 Series Scheda tecnica

Arregui

Arregui CLASS Manuale utente

Beaumont

Beaumont SMART KEYBOX Manuale utente

Hornady

Hornady SnapSafe Trunk Safe II Manuale utente

SPORTS AFIELD

SPORTS AFIELD SA-HD5-BIO Manuale utente

Phoenix

Phoenix FS1280F Manuale utente

Phoenix

Phoenix SS0992K Scheda informativa del prodotto

Technomax

Technomax Trony Series Manuale

SPORTS AFIELD

SPORTS AFIELD INSTINCT BIOMETRIC Series Manuale utente

RICHTER CZECH

RICHTER CZECH LA Manuale operativo

Olymp

Olymp GOsafe 110 Manuale utente

Phoenix

Phoenix SS0100E Scheda informativa del prodotto

Clarke

Clarke Strong-Arm CS1000K Manuale di istruzioni

Ankaro

Ankaro ANK EZ I Manuale utente

Phoenix

Phoenix FS1270E Series Manuale utente