Honeywell BW Ultra Manuale utente

Honeywell BW ™ Ultra

Quick

Reference

Guide

| Gas Detection

Portable Five-gas Detector

with Internal Pump

ENGLISH

Introduction

The Honeywell BW ™ Ultra gas detector warns of

hazardous gas at levels above user-deﬁned alarm

setpoints.

The detector is a personal safety device. It is your

responsibility to respond properly to the alarm.

Monitored Gases

The detector can monitor up to ﬁve gases at a time.

Refer to the Honeywell BW ™ Ultra User Manual for the full

list of gases.

What’s in the Box

• Honeywell BW ™ Ultra gas

detector

• Quick Reference Guide

• Battery (factory-installed) • Screwdrivertelescopewithdoubleend

• Charging adapter • 3m PVC tube

• 1 Dust porous ﬁlter 7/16” • 2Fittingminiquickconnectorto1/8”

• 5 Pump ﬁlters • 2 Fitting male LuerLock to 1/8”

• USB memory stick

containing user manuals

• 1 screen protector (factory-installed)

Safety Information

Use the detector only as speciﬁed in this manual,

otherwise, the protection provided by the detector may be

impaired.

• Only the instrument capable of sounding the alarms and showing readings

on a display should be used for immediate safety critical use. Wireless

communication and infrastructure are only for informational monitoring.

• Useonly HoneywellHUBATbatterypack.Usinganyotherbatterycancause

an explosion or ﬁre.

• Deactivatingthedetectorbyremovingthebatterypackmaycauseimproper

operation and harm the detector.

• Use only Honeywell approved battery chargers such as the MultiUnit

Cradle Charger.

• Ifusingthedetectornearitsupperorloweroperatingtemperature,Honeywell

recommends zeroing or activating the detector in that environment.

• Charge the detector before first-time use. Honeywell recommends the

detector also be charged after every workday.

• Calibrate the device on a regular schedule, depending on use and sensor

exposure to poisons and contaminants. Honeywell recommends calibrating

at least once every six months.

• Foroptimalperformance,periodicallyzerothesensorinanormalatmosphere

(20.9% v/v O) that is free of hazardous gas.

• The combustible sensor is factory calibrated to 50% LEL methane. If

monitoring a different combustible gas in the % LEL range, calibrate the

sensor using the appropriate gas.

• Onlythecombustiblegasdetectionportionofthisdetectorhasbeenassessed

for performance by CSA International.

• Honeywellrecommendsthatthecombustiblesensorischeckedwithaknown

concentrationofcalibrationgasafteranyexposuretocontaminants/poisons

such as sulfur compounds, silicone vapors, halogenated compounds, etc.

ENGLISH

• Honeywell recommends that the sensors be bump tested before each day’s

usetoconﬁrmtheirabilitytorespondtogas.Manuallyverifythattheaudible,

visual, and vibrator alarms are activated. Calibrate if the readings are not

within the speciﬁed limits.

• Portablesafetygasdetectorsarelifesafetydevices.Theaccuracyofambient

gasreading(s)isdependentuponfactorssuchasaccuracyofthecalibration

gas standard used for calibration and frequency of calibration.

• The detector is designed for use only in potentially explosive atmospheres

where oxygen concentrations do not exceed 20.9% (v/v). Oxygen deﬁcient

atmospheres (<10% v/v) may suppress some sensor outputs.

• Extendedexposureofthedetectortocertainconcentrations ofcombustible

gases and air may stress the detector element and seriously affect its

performance. If an alarm occurs due to a high concentration of combustible

gases, a calibration should be performed. If necessary, replace the sensor.

• High concentrations of certain toxic gases, for example, H2S, may hurt the

LEL sensor. This effect, known as inhibition, is usually temporary but in

extreme circumstances can impair the sensitivity of the LEL sensor after

any gas exposure that causes alarm in the toxic gas sensors.

• TheHoneywellBW™UltraisprovidedwithanantistaticcoatingovertheLCD

windowtominimizetheriskofignitionduetoelectrostaticdischarge.Periodic

inspectionofthiscoatingisrequiredtoensurenodegradation,delamination,

abrasions or other deformities to this surface.

• Care must be taken to avoid exposure to excessive heat, harsh chemicals

or solvents, sharp edges and abrasive surfaces. Clean the exterior with a

soft, damp cloth.

• The Canadian Standards Association (CSA) requires the LEL sensor to be

bump tested before each day’s use with calibration gas containing between

25% and 50% LEL. The instrument must be calibrated if the displayed

LEL value during a bump test fails to fall between 100% and 120% of the

expected value for the gas.

aWARNINGS

• Warning: Substitution of components may impair Intrinsic Safety.

• To prevent ignition of ﬂammable or combustible atmospheres, disconnect

power before servicing.

• Protectthecombustiblesensorfromexposuretoleadcompounds,silicones,

and chlorinated hydrocarbons. Although certain organic vapors (such as

leaded gasoline and halogenated hydrocarbons) can temporarily inhibit

sensor performance, in most cases the sensor will recover after calibration.

• Caution:Highoff-scaleLELreadingsmayindicateanexplosiveconcentration.

• Any rapid up scaling reading followed by a declining or erratic reading may

indicate a gas concentration beyond the upper scale limit, which can be

hazardous.

• Products may contain materials that are regulated for transportation under

domesticandinternational dangerousgoodsregulations. Return productin

compliance with appropriate dangerous goods regulations. Contact freight

carrier for further instructions.

• The lithium battery may present a risk of ﬁre or chemical burn hazard if

misused. Do not disassemble, incinerate, or heat above 212°F (100°C), or

incinerate.Batteries must only be charged in a safe area free of hazardous

gas.Batterieseexposedto heatat266°F(130°C)for10minutescancause

ﬁre and explosion.

• Disposeofusedlithiumcellsimmediately.Donotmixbatteries withthesolid

waste stream. Spent batteries should be disposed of by a qualiﬁed recycler

or hazardous materials handler.

ENGLISH

Appearance

1. Visual alarm

indicator

2. Exhaust port

3. Screen

4. Button

5. Beeper Aperture

6. Pump inlet

7. Alligator clip

8. Pump assembly

9. Charging

connector and IR

Interface

Screen Icons

Several icons are displayed in the detector’s screen as

conditions dictate.

BW ULTRA

ENGLISH

Screen Icons

BLE Pump/header

BLE Pairing

Error Pump passed

Paired Pump critical fail

Pairing failed Warning/failure/

error/low battery

Stealth mode

enabled

Hole watch

mode high

Battery -three

levels

Hole watch

mode low

Low battery Hole watch

Oxygen bar

IR LINK

connection

Correction factor

Calibration

passed

Peak gas

exposure

Calibration

failed

Press button

Calibration

cancelled

Press and hold

button

Screen Icons

Target gas Inert mode

Bump test

cancelled

Sensor failure

Bump test

passed

STEL alarm

Bump test

failed

TWA alarm

Over limit

alarm

Firmware update

in progress

High alarm Sensor disabled

Low alarm Heartbeat

ENGLISH

Activate the Detector

Activate the detector in a safe area with an atmosphere of

20.9% oxygen and free of hazardous gas.

1. For ﬁrst time use, charge the battery for up to 8 hours or

until LED light turns green using the charging adapter

provided. Refer to Charge the battery for more information.

2. Press and hold the button for three seconds.

3. For ﬁrst time use, a Warming sensors message is

displayed and a 30 minutes countdown is displayed. In

most cases, this countdown only lasts a couple of minutes.

4. When the detector displays Pump test Block inlet,

block the pump inlet with a ﬁnger, and then after a couple

of seconds unblock the pump inlet.

The detector performs a quick pump test. A Pump Test

passed message is displayed.

If you do not block the pump inlet, the detector will turn off

after two minutes.

If necessary, you will be instructed by screen prompts to

calibrate newly-installed sensors.

The detector will then perform a self-test, including testing

the sensors. This process could take several minutes.

5. When the self-test is complete, press and hold the button

to zero sensors. After the autozero is complete, the detector

then checks the sensors for calibration and bump test.

If the detector identiﬁes sensors requiring calibration or

bump testing, press the button and follow the on-screen

instructions.

Altri manuali per BW Ultra

Indice

Altri manuali Honeywell Sensore di sicurezza

Honeywell

Honeywell C7076D Manuale operativo

Honeywell

Honeywell MultiPro Manuale utente

Honeywell

Honeywell Smart Seal P3S Manuale utente

Honeywell

Honeywell C7061A1020 Manuale utente

Honeywell

Honeywell Searchline Excel Cross-Duct Nota di rilascio

Honeywell

Honeywell 14506873-001 Manuale utente

Honeywell

Honeywell Miller Scorpion Manuale utente

Honeywell

Honeywell C7061M Manuale operativo

Honeywell

Honeywell C7061A1020 Manuale utente

Honeywell

Honeywell Fire-Lite Alarms SD365T Manuale utente

Honeywell

Honeywell H-S81-HS Manuale utente

Honeywell

Honeywell Ex-Or MLS2500CDR Manuale di installazione e funzionamento

Honeywell

Honeywell Notifier FST-951 Manuale utente

Honeywell

Honeywell FlexGuard 5853 Manuale utente

Honeywell

Honeywell 5800PIR-RES Manuale utente

Honeywell

Honeywell IS216 Manuale di installazione e funzionamento

Honeywell

Honeywell 5800CO Istruzioni per il montaggio

Honeywell

Honeywell Farenhyt Series Manuale utente

Honeywell

Honeywell ADEMCO 5821 Manuale utente

Honeywell

Honeywell Lyric Manuale utente

Honeywell

Honeywell IRPI8EZS Manuale utente

Honeywell

Honeywell C08MS Manuale utente

Honeywell

Honeywell Lyric W1 Manuale utente

Honeywell

Honeywell PROINDMV Istruzioni per il montaggio

Manuali Sensore di sicurezza popolari di altre marche

THORLABS

THORLABS PDA10JT Manuale utente

Waeco

Waeco UV-DETECT Manuale utente

Intermatic

Intermatic IOS-DSIMF Manuale utente

urmet domus

urmet domus 1083 Manuale utente

Siemens

Siemens AZL66 Series Manuale utente

BTI

BTI Profiline Multi Finder Manuale utente

Challenger

Challenger SL01 Manuale utente

DMP Electronics

DMP Electronics 1122INT Manuale utente

Rielta

Rielta Ladoga MK-RK Manuale utente

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuale utente

Bosch

Bosch DS835 Manuale utente

DBI SALA

DBI SALA EZ Stop Manuale dell'operatore

Lamptime

Lamptime ST05C Manuale utente

Ubiquiti

Ubiquiti MFI-MSC Manuale utente

Subsite

Subsite 910R Istruzioni per l'installazione

Satel

Satel OPAL Pro Manuale utente

Aleph

Aleph XC-1XTEU Manuale utente

Pima

Pima LARIS QUAD Manuale utente