Honeywell LYNX TOUCH L5200 Manuale utente

How to Use the Lynx 5200 Alarm System

Using your alarm system

There are multiple ways to turn your new Honeywell alarm system on and multiple ways

the system can protect you. The buttons in the red box below are your shortcut keys. These

buttons help make your system easier and quicker to use. The device to the right is your keyfob.

The keyfob can make your system very quick and easy to use.

How to turn your system on

Turning your system on is also known as arming the system. There are a couple different

ways to arm your system. There are also a couple different modes for arming your alarm system

depending on the different devices that have been installed. Before you can arm your system, the

system has to be ready to arm. The keypad will tell you this on the display and as well with a

green led. (Note the above keypad is ready to arm) If the key pad is not ready to arm it will read

NOT READY TO ARM FAULT and the green bar at the top will turn to yellow. See keypad

below. If you press the ZONES button this will show you what zones are faulted. If your keypad

says you have a fault but the zones button says everything is okay then a panic button was

pushed and you will have to clear the keypad (please see the CLEARING THE KEYPAD

section of this guide)

Now let’s focus on the first mode for arming your system. The first mode is called

AWAY in this mode every device will be turned on and is meant to be used when no one will be

in the house after the system is armed. Certain devices such as the door and motion sensors can

be on delay. The delay time will be set up between you and the installer. There are multiple ways

to arm your system for away. The first way is to use one of the “ARM AWAY” buttons that is

on your keypad. When you use either of these buttons you need to either put in

your four digit code or press the quick arm button. The second way to arm your system

for stay is to use the wireless keyfob that came with your system. To use the keyfob simply press

and hold the arm away button for about 5 seconds. Once you do either of these methods for

arming away the keypad will then look like this

The second mode for arming your system is known as STAY. Stay is for people who

have motion sensors installed. If you DO NOT have motion sensors installed the only action stay

does for you is a silent count down for the alarm to turn on as normal. If you DO have motion

sensors installed when you arm for stay everything BUT the motion sensors will be armed. To

reiterate when armed in STAY your motion sensors WILL NOT be on so you can freely move

around the house and still be protected by other devices (i.e. glassbreaks, door/window switches)

To arm in STAY mode push and hold the shortcut button on your keypad that says arm stay

The second way to arm in stay mode is to push and hold the button on your keyfob that

has a little man inside a house. Once you have armed the system the keypad will read

"ARMED STAY EXIT NOW" (similar to the large picture above)

Turning your system OFF

Turning your system off or disarming the system, as it is called, is different than

arming the system when done at the keypad. To disarm the system from the keypad all

you have to do is push the green disarm button and put in your four digit code or when

you walk through the delay door it will automatically ask for your four digit code you

will then enter your code. Another way to disarm your system is to push and hold the

unlocked lock button located on the keyfob.

EMERGENCY

If you ever have an emergency where you need the police to be called you have a couple

of different options. If you are able to make it to the keypad there will be a shortcut button that

has a red triangle on it push and hold this button and then select either police or fire and a

silent alarm will be sent out. If you have your keyfob and are within range of the system you can

push and hold the red star and a silent alarm will be sent out. Either of these options will

work if the alarm system is disarmed. Silent alarms are treated just like any other alarm by your

alarm panel and Emergency 24. You should get a call from Emergency24 and then you follow

the necessary procedure to either cancel or accept the alarm.

Clearing the Keypad

Whenever an alarm goes off silent or audible you will have to clear the keypad. This is a

two-step process, if you have an audible alarm (siren is going off) the keypad will say ALARM

the zone number and a description of the zone to silence it enter your four digit code. The keypad

will say it is not ready to arm and then you will have to press the green disarm button and then

enter your four digit code again to clear it. This will take it back to its normal state. If a silent

alarm goes off you will have to press the unlocked lock button on the front of the keypad.

Once you hit the button on the front, enter your four digit code and it will reset the keypad.

Misc. Information

HELP IM LOST!!

The Lynx 5200 has many features and navigating to and from these features can

sometimes get confusing for new users, if you ever find yourself at an unfamiliar screen and you

want to get back to a screen that you do know just simply press the HOME button on the front of

the keypad. This button will return you to the main screen you see when your first

using your system.

Chime Mode

One of the most popular features is known as Chime mode. While disarmed and with

chime mode activated, whenever a door is opened the keypad will chime. Chime mode can be

turned on and off whenever you would like to do this press the MORE button in the lower right

hand corner of the screen, then press the SETTINGS button. This will take

you to the screen below.

Once on the settings page you can select the option CHIME.

Voice Chime

When you start using your system you will notice that the Lynx 5100 actually talks to

you and tells a lot of audible information so that you don’t have to go look at the keypad to see

what is happening. Some people do not enjoy the voice and just want a simple chime to do this

follow the steps above for CHIME mode but instead of toggling the chime option you will

toggle the VOICE option.

Adding Codes

Another feature is you can have 48 different codes programmed into your alarm system and are

able to add and delete them as you like. (Be sure to make a list of all the codes and contact R.J.

Beck 419-668-3056 if you change codes so your code is valid with Emergency24) To add a user

code select the MORE button in the bottom right hand corner and then select the TOOLS button

and then enter your four digit code. This will take you to the screen below.

once here select the USERS button once you select this

button this screen will appear then you will select ADD NEW

and then select the area that says USER CODE and then enter the new code be sure

to hit save.

Deleting Codes

To delete a code follow the steps to adding a code but instead of pressing add new you

will highlight the code you would like to delete and then select DELETE.

Testing Your Alarm System

To test your alarm system first you must call Emergency 24 at 1-800-424-3624 the

operator will answer and you will tell them your six (6) digit account number and then your four

(4) digit code you use to disarm your alarm system. Once you tell them this data tell them you

would like to put the system on test for 2 hours. Once your system is on test turn your system on

for away and open and close the delay door and wait for the delay timer to run out and your

system to arm. Once the system is armed open and close of the doors/windows, walk in front of

motion sensors, and use something firm and hit the GLASSBREAKS not the glass but the

device. This will put your system into an alarm. Once you have activated every device go to the

keypad and disarm the system ONCE and only ONCE for now. After you have disarmed the

system on the keypad press the ZONES button to view which devices went into alarm.

(Reference your zone list for this) If any devices did not show up on the keypad repeat the

previous steps but only activate the devices that did not show up the first time. (If they do not

show again call R.J. Beck for service) once you get all of your devices activated and referenced

disarm your system again and then call Emergency 24 back and give them the information again

and then ask if they have received any signals recently. If they receive all of the signals and all of

your devices showed up on the keypad tell them to take the system off of test. If they do not

receive any signals call R.J. Beck for service.

Altri manuali per LYNX TOUCH L5200

Indice

Altri manuali Honeywell Sistema di sicurezza

Honeywell

Honeywell Code Encryptor II Manuale utente

Honeywell

Honeywell LYNX Touch Security System Manuale utente

Honeywell

Honeywell WAVE2EX - Ademco Two Tone Siren Istruzioni per il montaggio

Honeywell

Honeywell VISTA-32FBPT Istruzioni per il montaggio

Honeywell

Honeywell 5816 WMWH Manuale utente

Honeywell

Honeywell Domonial Manuale utente

Honeywell

Honeywell sixsiren Manuale utente

Honeywell

Honeywell Accenta Guida rapida

Honeywell

Honeywell ADEMCO LYNXR-I Security System Manuale utente

Honeywell

Honeywell PID-95P Guida

Honeywell

Honeywell ADEMCO LYNXR-ENSIA Manuale utente

Honeywell

Honeywell LYNXR Manuale utente

Honeywell

Honeywell ADEMCO 6150V Manuale utente

Honeywell

Honeywell VISTA-128BPT Istruzioni operative

Honeywell

Honeywell INTELLIGUARD 9000 Manuale

Honeywell

Honeywell GENT Manuale utente

Honeywell

Honeywell Notifier NFS2-640/E Manuale utente

Honeywell

Honeywell Domonial Manuale utente

Honeywell

Honeywell Fire-Lite Alarms MS-9200UDLSC Manuale utente

Honeywell

Honeywell S-Quad Manuale di istruzioni

Honeywell

Honeywell V4000 Manuale utente

Honeywell

Honeywell INTELLIGUARD 9000 Manuale utente

Honeywell

Honeywell ADEMCO VISTA-10P Istruzioni operative

Honeywell

Honeywell LYNX Touch Series Manuale utente

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente