HORNER WWPC40 Manuale utente
LMAN0052-01-EN
59 South State Ave., Indianapolis, IN 46201 | (p) 317.916.4274 (tf) 877.665.5666 (f) 317.639.4279 | www.hornerlighting.com
Product Description
The Wall Pack series lights are the latest innovation from
Horner Lighting providing high output, while saving energy.
There are two models of Wall Packs: WWP and WWPC, both
coming in 40W and 60W options.
Precautions
WARNINGS
Risk of electrical shock. Disconnect power before servicing or
installing product.
Risque de choc électrique. Coupez l’alimentation avant
l’entretien ou l’installation du produit.
Risk of injury or damage. Unit will fall if not installed properly.
Follow installation instructions.
Risque de blessures ou de dommages. Unité va tomber s’il n’est
pas installé correctement. Suivez les instructions d’installation.
Risk of injury. Wear safety glasses and gloves during installation
and servicing.
Risque de blessure. Porter des lunettes de sécurité et des gants
lors de l’installation et de l’entretien.
Risk of injury or damage. LED light sources achieve full intensity
immediately after powered. Do not look directly the lights.
Risque de blessures ou de dommages. Sources de lumière LED
parvenir à pleine intensité immédiatement après sous tension. Ne
regardez pas directement la lumière.
WALL PACK INSTALLATION GUIDE
Unit Installation
This guide is meant to be used for both the WWP and WWPC
models. Unpack the unit and check for any shipping damage.
NOTE: Wall Packs must match the input voltage to the supply
voltage. Please confirm the product voltage and supply
voltage match before installation.
WWPC40/
WWPC60
WWP40/
WWP60
Wall Pack Series Base
WWPC40/
WWPC60
WWP40/
WWP60
LMAN0052-01-EN
59 South State Ave., Indianapolis, IN 46201 | (p) 317.916.4274 (tf) 877.665.5666 (f) 317.639.4279 | www.hornerlighting.com
Cleaning
To maintain efficiency, the glass lens should be cleaned with
a mild soap or neutral PH cleaner.
Abrasives or cleaners containing chlorinated or aromatic hy-
drocarbons should not be used. Once clean, rinse with cold
water and wipe dry with a soft cloth.
Fixture Mounting
Mount the light base to the building using proper anchors for the building material. You may need to add additional support
behind the surface material.
Wiring
Make all electrical connections in accordance with the National Electrical Code and any applicable local code requirements.
Remove screw and lid to power
supply.
Attach ground to connector.
Bring incoming AC through opening.Open back of unit housing to access
power supply.
Attach line and neutral. Use diagram
on power supply.
Replace power supply lid and screw.
Technical Support
Tel: 317-916-4274
Fax: 317-639-4279
Email: techsppt@HornerETG.com
Web: http://www.hornerlighting.com
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali HORNER Luce esterna
Manuali Luce esterna popolari di altre marche
Lindby
Lindby 9949029 Manuale utente
HEPER
HEPER DOGO Side LW6048.585-US Istruzioni per l'installazione e il funzionamento
HEPER
HEPER LW8034.003-US Istruzioni per l'installazione e il funzionamento
Maretti
Maretti VIBE S 14.6080.04.A Manuale utente
BEGA
BEGA 84 253 Manuale
HEPER
HEPER MINIMO Istruzioni per l'installazione e il funzionamento
LIGMAN
LIGMAN BAMBOO 3 Manuale utente
Maretti
Maretti TUBE CUBE WALL 14.4998.04 Manuale utente
Maxim Lighting
Maxim Lighting Carriage House VX 40428WGOB Manuale utente
urban ambiance
urban ambiance UQL1273 Manuale utente
TotalPond
TotalPond 52238 Manuale utente
Donner & Blitzen
Donner & Blitzen 0-02661479-2 Manuale utente