HP iPAQ Manuale utente
User’s Guide
hp iPAQ Navigation System
Document Part Number: 366337-001
March 2004
© Copyright 2003 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice.
Microsoft, MS-DOS, Windows, and Windows NT are trademarks of Microsoft Corporation in the U.S. and other
countries.
Intel, Pentium, Intel Inside, and Celeron are trademarks of Intel Corporation in the U.S. and other countries.
Adobe, Acrobat, and Acrobat Reader are trademarks or registered trademarks of Adobe Systems Incorporated.
SD is a trademark of Secure Digital.
The only warranties for HP products and services are set forth in the express warranty statements accompanying
such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or omissions contained herein.
This document contains proprietary information that is protected by copyright. No part of this document may be
photocopied, reproduced, or translated to another language without the prior written consent of Hewlett-Packard
Company.
ÅWARNING: Text set off in this manner indicates that failure to follow directions could result in bodily
harm or loss of life.
ÄCAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to
equipment or loss of information.
User’s Guide
hp iPAQ Navigation System
First Edition (March 2004)
Document Part Number: 366337-001
User’s Guide www.hp.com 3
Using the HP iPAQ GPS Bluetooth Receiver
The HP iPAQ Navigation System Bluetooth GPS receiver gets GPS signals from satellites
orbiting the earth. It identifies your position to an accuracy of less than 10 meters.
✎Note: The HP iPAQ Navigation System Bluetooth GPS receiver is referred to as the Bluetooth
GPS receiver in this User’s Guide.
Learning About Bluetooth GPS Features
An illustration of the Bluetooth GPS receiver with features follows.
Feature Description
Power Switch Power is On or Off.
Power Jack The Power Jack connects a DC car power charger (included) or AC
power charger to recharge the internal battery.
Bluetooth Status LED
(Blue)
Blinking Slowly - There is not a Bluetooth connection.
Blinking Quickly - There is a connection to another Bluetooth
receiver.
GPS Status LED
(Green)
Blinking - The GPS position is fixed.
Steady Light - The GPS position is not fixed.
Battery Status LED
(Red/Yellow)
Red - Battery power is extremely low. Charge immediately.
Yellow - Battery is currently charging.
LED Off - Battery is partially or fully charged.
External Antenna Connects an external antenna. This is usually not required since the
GPS has an internal antenna.
Power Jack
Power
Switch
Bluetooth Status
GPS Status
Battery
External Antenna
4 www.hp.com User’s Guide
Setting Up the Bluetooth GPS Receiver
The Navigation System requires set up with the Bluetooth GPS receiver in order to operate. For
the initial set up, do the following:
1. Charge the Bluetooth GPS receiver using the DC adapter (included) or the AC adapter for the
HP iPAQ PocketPC.
✎Note: The first time you charge the Bluetooth GPS receiver, it can take up to three hours.
2. Turn on the Bluetooth GPS receiver using the Power switch on the left side of the receiver.
✎Note: The blue LED flashes when the receiver is turned on.
Manually Partnering for Windows®Mobile 2002
Operating System
✎Note: Some devices require you manually partner the Bluetooth GPS receiver and the iPAQ
PocketPC. This includes devices using Microsoft®Windows Pocket PC 2002 operating system.
For more information, refer to the Manually Partnering the Bluetooth GPS Receiver and the
iPAQ PocketPC section.
To partner the Bluetooth GPS receiver with the iPAQ PocketPC requires:
■Navigation System software installed on your iPAQ PocketPC.
■Bluetooth GPS receiver is charged.
■iPAQ PocketPC is turned on.
■Bluetooth GPS receiver is turned on.
■Bluetooth GPS receiver and iPAQ PocketPC are between 5-10 meters apart.
Establishing a Connection
1. Tap Start at the top of the Today screen on the iPAQ PocketPC.
2. Tap Bluetooth Manager from the pop up menu.
The Bluetooth Manager screen displays.
User’s Guide www.hp.com 5
3. Tap the Yes tab to search for devices.
✎Note: iPAQ searches for and displays a list of Bluetooth devices.
4. Tap the check box to the left of the BT-GPS-xxxxxx device in the list.
5. Tap the OK button on the upper right side of the screen.
6 www.hp.com User’s Guide
✎Note: A Bluetooth GPS icon displays on the Bluetooth Manager screen.
6. Tap and hold the pointer on the BT-GPSxxxxxx icon.
7. Tap on Connect to Serial xxxxxx to establish a connection with the Bluetooth GPS receiver.
User’s Guide www.hp.com 7
✎Note: Two blue arrows display on the GPS Bluetooth receiver icon to indicate a connection.
Partnering between the Bluetooth GPS receiver and the iPAQ PocketPC immediately occurs.
Manually Partnering for Windows®Mobile 2003 Operating
System
To partner the Bluetooth receiver with the iPAQ PocketPC requires:
■Navigation System Software installed on your iPAQ PocketPC.
■Bluetooth GPS Receiver is charged.
■iPAQ PocketPC is turned on.
■Bluetooth GPS Receiver is turned on.
■Bluetooth GPS receiver and iPAQ PocketPC are between 5-10 meters of each other.
Establishing a Connection
1. Tap Start at the top of the Today screen on the iPAQ PocketPC.
2. Tap the Settings option on the pop up menu.
3. Tap the System tab at the bottom of the Settings menu.
4. Tap the Bluetooth icon on the System menu.
The Bluetooth General screen displays.
5. Tap the Turn On tab below the Bluetooth status.
8 www.hp.com User’s Guide
✎Note: The message “Bluetooth is On” displays.
6. Tap Bluetooth Manager to set the connections.
The Bluetooth screen displays.
7. Tap the New tab at the bottom of the Bluetooth screen.
8. Tap Connect! to display the Connection Wizard.
9. Tap Explore a Bluetooth Device from the Connection Wizard options.
10. Tap the Next tab at the bottom of the Connection Wizard screen
User’s Guide www.hp.com 9
11. Tap inside the Device box to display a list of available Bluetooth Devices.
✎Note: The Bluetooth GPS receiver displays a list of available devices. This creates a shortcut for
the GPS receiver
12. Tap the icon labeled BT-GPS-XXXXXX.
13. Tap Serial XXXXXX on the Service Selection screen to highlight it.
14. Tap the Next tab at the bottom of the Service Selection screen.
15. Tap the Finish tab at the bottom of the Connection Wizard screen.
✎Note: A box with the connections displays.
16. Tap the BT-GPS-XXXXXX icon, twice, to establish a connection between the iPAQ
PocketPC and the Bluetooth GPS receiver.
17. Green arrows on the icon indicate an active connection.
10 www.hp.com User’s Guide
Checking the GPS Connection Status
1. To check the status for the Bluetooth GPS receiver and the iPAQ PocketPC, tap the Bluetooth
icon on the Today screen.
✎Note: The Bluetooth icon is located on the lower right side of the screen.
2. Tap Bluetooth Manager.
3. The Bluetooth Manager screen displays.
4. Tap the Active Connections tab at the bottom of the screen.
If a connection is established, an icon with the label “BT-GPS-XXXXXX” displays. The green
line next to the icon indicates an active connection.
Altri manuali per iPAQ
8
Indice
