HP Integrity rx1600 Manuale utente

February 2004

Printed in the U.S.A.

Smart Array (A9890A) Cable Routing

The purpose of this document is to provide cable routing information when a Smart Array PCI-X RAID card (A9890A)

is used to drive the embedded hard disk drives. The existing SCSI cable connected to the Channel A connector on the

system board is relocated to the Channel A connector on the Smart Array PCI-X card installed in slot 1 (full-length slot)

of the PCI cage.

The SCSI cable is routed from the PCI cage under the power supply bracket and over the IDE cable, if installed, avoiding

blocking the airflow of the chassis fans.

Refer to the hp integrity rx1600 Operation and Maintenance Guide for detailed instructions on powering down the

server, extending the server from a rack, and removing and replacing covers and components.

1. Disconnect the SCSI cable from the Channel A connector on the system board by pulling on the cable release strap.

See figure 1.

Figure 1. SCSI Channel A Connector on System Board

2. Remove the PCI cage from the server.

3. Remove any accessory card installed in PCI slot 2 (half-length slot).

4. Install the Smart Array PCI-X RAID card (A9890A) in PCI slot 1 (full-length slot).

5. Orient the PCI cage with the installed PCI-X RAID card component-side-up allowing routing of the SCSI cable.

See figure 2.

Figure 2. Cable Routing on Smart Array Card and PCI Cage

NOTE If an optional management processor card is installed in the server, follow the

instructions provided in the hp integrity rx1600 Operation and Maintenance Guide to

remove the card, allowing access to the Channel A connector. Reinstall the card after the

SCSI cable has been disconnected.

Channel A

connector

Around heatsink

Exit parallel to

connector

Channel A1

Under slot 2 connector

6. Attach the SCSI Channel A connector (previously removed from the system board connector) to the A1 Channel of

the PCI-X RAID card.

7. Route the SCSI cable around the heatsink on the PCI-X RAID card and under the edge of the PCI slot 2 connector.

See figure 2.

8. Continue routing the cable parallel to the connector edge of the PCI cage.

9. Reinstall any accessory card previously removed from PCI slot 2.

10. Install the PCI cage into the server chassis.

11. Route the SCSI cable under the power supply bracket as shown in figure 3.

Figure 3. Route Cable under Power Supply Bracket

12. Route the SCSI cable through the access slot of the fan assembly to the connector on the SCSI backplane.

See figure 4.

Figure 4. Cable Routing at SCSI Cage

13. Complete the installation by following the instructions provided in the hp integrity rx1600 Operation and

Maintenance Guide for closing up the server, installing in a rack, and powering-up. To enable RAID refer to the

A9890A documentation.

NOTE The SCSI cable should be routed over the IDE cable if the IDE cable is present.

CAUTION Do not block the airflow of the chassis fans. Reduced airflow may cause overheating.

Power Supply

Bracket

Route over IDE

cable (if present)

Do not block fans

Altri manuali per Integrity rx1600

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali HP Hardware per computer

HP Kayak XU04 Manuale dell'operatore

HP 10512 Istruzioni per l'installazione

HP Kayak XW U3-W3 Manuale utente

HP A1250 Series Istruzioni per il montaggio

HP NVIDIA Tesla M2070Q Manuale utente

HP AB479A Manuale utente

HP M8201R Manuale utente

HP Metal Jet S100 Manuale utente

HP Xw4600 - Workstation - 2 GB RAM Manuale utente

HP OmniBook 3100 Manuale utente

HP E5000 Manuale utente

HP E2465A PowerPC 604 PGA Manuale utente

HP Rp5700 - Point of Sale System Istruzioni per l'installazione

HP HP 27113A Manuale

HP 81200 Manuale utente

HP A3550A - High Availability Disk Arrays Model 20 Storage... Manuale utente

HP MicroServe Manuale utente

HP rp7420 Manuale utente

HP 3000 Series Manuale

HP MCS G2 Guida all'installazione

HP A58 0AF Series Istruzioni per il montaggio

HP C-CLASS BLADESYSTEM 409513-B21 Istruzioni utente

HP 64782 Manuale utente

HP JG560A Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente