HP StorageWorks 2312 Manuale utente

Questo manuale è adatto per i seguenti modelli

1

Altri manuali HP Controllori

HP

HP HPE VAN SDN Controller 2.7 Manuale di servizio

HP

HP P420 Manuale utente

HP

HP ProCurve MSM765zl Manuale utente

HP

HP ProCurve MSM765zl Manuale utente

HP

HP VXI 75000 C Series Manuale del proprietario

HP

HP MSM775 zl Manuale utente

HP

HP A9890A - Smart Array 6402/128 RAID... Manuale utente

HP

HP VXI Pentium Series Manuale utente

HP

HP StorageWorks 1510i - Modular Smart Array Manuale utente

HP

HP Smart Array P830 Manuale utente

HP

HP Smart Array P711m Istruzioni utente

HP

HP 9000 Series 700 Manuale utente

HP

HP Smart Array P430 Istruzioni utente

HP

HP Smart Array P712m Istruzioni utente

HP

HP 273914-B21 - Smart Array 6404/256 RAID... Manuale utente

HP

HP Compaq Presario,Presario 4400 Guida

HP

HP 9000 Series 300 Come usare

HP

HP D5970A - NetServer - LCII Manuale utente

HP

HP StorageWorks HSG60 Manuale utente

HP

HP MSA 2040 Manuale utente

HP

HP Smart Array P600 Manuale utente

HP

HP 3100ES - Smart Array RAID Controller Manuale utente

HP

HP HSG80 - StorageWorks RAID Array Controller Manuale utente

HP

HP MSM720 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente

HP StorageWorks 2312/2324

Modular Smart Array controller

installation instructions

© Copyright 1999, 2008 Hewlett-Packard Development Company,

L.P.

First edition: November, 2008

The informationinthisdocumentissubjecttochangewithout

notice.

Printed in the China

www.hp.com

508933-001

About this document

This document describes procedures for installing a controller into an

HP StorageWorks 2312/2324 Modular Smart Array.

Before you begin

CAUTION:

When upgrading an existing operational system with a second

optional controller, removing the air management blank impacts

the airﬂow and cooling ability of the device. To avoid possible

overheating, insert the controller as quickly as possible. If the

internal temperature exceeds acceptable limits, the enclosure may

overheat and automatically shut down or restart.

CAUTION:

Parts can be damaged by electrostatic discharge. Use proper

anti-static protection.

•Keep the replacement component in the ESD bag until needed.

•Wear an ESD wrist strap grounded to an unpainted surface

of the chassis.

•If an ESD wrist strap is unavailable, touch an unpainted surface

of the chassis before handling the component.

•Never touch connector pins.

Installing a controller (single or dual) for

the ﬁrst time

Remove the air management blank(s)

NOTE:

For clarity, only relevant details are shown in these illustrations.

1. Turn the thumbscrews until the screws disengage from the blank.

1—Lat

ch 2—Thu

mbscrew

2. Press both latches downward.

Page 1

3. Pull the blank straight out of the enclosure.

Install controller(s)

NOTE:

For clarity, only relevant details are shown in these illustrations.

1. Loosen the thumbscrews; press the latches downward.

2. Slide the controller into the enclosure as far as it will go (1).

3. Press the latches upward to engage the controller (2); turn the

thumbscrews ﬁnger-tight.

4. Connect cables according to a supported conﬁguration. See the

user guide.

Upgrading an existing single controller

system to a dual controller

If you have an existing single controller system and you are adding a

second controller, the new controller automatically begins to initialize

when it is installed. If the ﬁrmware versions differ between the two

controllers, Partner Firmware Upgrade feature brings the older ﬁrmware

to the later ﬁrmware level.

Verifying Partner Firmware Upgrade is

enabled

By default the storage system’s Partner Firmware Upgrade feature is

enabled, so when you upgrade a controller the system automatically

ensures that both controllers have the more recent version.

•Log in to the command-line interface (CLI) and run the following

command to verify that Partner Firmware Upgrade is enabled.

show advanced-settings

If Partner Firmware Upgrade is disabled, enable it by running the

command:

set advanced-settings partner-firmware-upgrade

enabled

Verifying controller status

Once the controller completes initializing and is online:

•Verify that the heartbeat LED on the front of the enclosure is green.

•Verify that the OK LED on the back of the controller is green.

NOTE:

If the OK LED is blinking, the controller is still initializing.

Additional information

See the MSA web site: http://www.hp.com/go/msa.

Page 2