HP Compaq dc5100 Series Istruzioni per il montaggio

HP-00007-01, Appendix 3 04-Jan-2006

HP Restricted

Page 1

Appendix 3 Product End-of-Life Disassembly instructions

Product Identification:

Marketing Name / Model Description

HP Compaq Business Desktop dc5100 Series,

version 2 - SFF HP business desktop PC – Small Form Factor

Purpose: The document is intended for use by end-of-life recyclers or treatment facilities. It provides the

basic instructions for the disassembly of HP products to remove components and materials requiring

selective treatment.

1.0 Items Requiring Selective Treatment

1.1 Items listed below are classified as requiring selective treatment.

1.2 Enter the quantity of items contained within the product which require selective treatment in

the right column, as applicable.

Item Description

Notes Qty items in

product.

Printed Circuit Boards (PCB) or Printed

Circuit Assemblies (PCA) With a surface greater than 10

square cm 2 (sys bd, power

supply PCA)

Batteries All types including standard

alkaline & lithium coin/button style 1

Mercury containing components For example, mercury in lamps,

display backlights, scanner lamps,

switches, batteries

Liquid Crystal Displays (LCD) with a

surface greater than 100 square cm Includes background illuminated

displays with gas discharge lamps

Cathode Ray Tubes (CRT)

Capacitors / condensers (PCB / PCT)

Electrolytic Capacitors / Condensers

measuring greater than 2.5 cm in

diameter or height

External electrical cables and cords PSU, IDE, SATA cables.

Gas Discharge Lamps

Plastics containing Brominated Flame

Retardants

Components and parts containing toner

and ink, including liquids, semi-liquids

(gel/paste) and toner

Include the cartridges, print

heads, tubes, vent chambers, and

service stations.

Components and waste containing

asbestos

Components, parts and materials

containing refractory ceramic fibers

Components, parts and materials

containing radioactive substances

HP-00007-01, Appendix 3 04-Jan-2006

HP Restricted

Page 2

2.0 Tools Required

List the type and size of the tools that would typically be used to disassemble the product to a

point where components and materials requiring selective treatment can be removed.

Tool Description Tool Size (if applicable)

Flat blade screwdriver

Phillips screwdriver

Pry bar 6 to 8-inch

Diagonal cutters (dikes)

3.0 Product Disassembly Process

3.1 List the basic steps that should typically be followed to remove components and materials

requiring selective treatment:

SFF CHASSIS IDENTIFICATION

There are two different Small Form Factor chassis types. Use the following information to

determine which chassis you have.

- The Type I chassis uses a drive cage that slides out from the front of the chassis

(see Figure 1 below).

- The Type II chassis uses a drive cage that rotates up from the chassis (see Figure 2 below).

SYSTEM BOARD – Type 1 SFF Chassis

1 To remove the computer cover (see Figure 3 below):

a) Press the buttons on the left and right sides of the computer

b) Slide the computer cover towards the front of the computer until it stops 2 then, lift it

up and off the chassis.

2 Remove all expansion cards, cables, and any other devices connected to the

system board.

3 Remove the fan shroud from the chassis (see Figure 4 below).

4 Slide the drive tray forward and disconnect the drive and power cables from the system

board (see Figure 5 below).

5 If applicable, remove the security clip (see Figure 6 below).

NOTE: The security clip is an optional feature and is not installed on all computers.

6 Rotate the power supply to its upright position (see Figure 7 below).

7 Disconnect the serial port from the system board (see Figure 8 below).

8 Remove the long mounting screw that secures the system board tray to the chassis

(see Figure 9 below).

9 Slide the system board tray assembly toward the front of the chassis, about 1/4 inch, and

then lift the system board up and out of the chassis (see Figure 10 below).

HP-00007-01, Appendix 3 04-Jan-2006

HP Restricted

Page 3

POWER SUPPLY - Type 1 SFF Chassis

1 If applicable, remove the security clip (see Figure 11 below).

NOTE: The security clip is an optional feature and is not installed on all computers.

2 Rotate the power supply to its upright position.

3 Pull the drive cage forward and disconnect the power cables from all of the drives.

4 Release the power supply cable from the cable retaining clip at the front of the chassis

below the drive cage and from the clip on the side of the chassis in front of the hard

drive.

5 Lift the power supply up and out of the chassis (see Figure 12 below).

SYSTEM BOARD – Type 2 SFF Chassis

1 To remove the computer cover (see Figure 13 below):

a) Press the buttons on the left and right sides of the computer

b) Slide the computer cover towards the front of the computer until it stops 2 then, lift it

up and off the chassis.

2 Remove all expansion cards from the system board.

3 Remove the fan shroud from the chassis (see Figure 14 below).

4 Rotate the drive cage to its full upright position.

5 If applicable, remove the security clip and rotate the power supply to its full upright

position (see Figure 15).

NOTE: The security clip is an optional feature and is not installed on all computers.

6 Disconnect the data and power cables from the system board (see Figure 16 below).

7 Disconnect the serial port from the system board (see Figure 17 below).

8 Disconnect the balance of the cables from the system board.

9 Remove the long mounting screw that secures the system board tray to the chassis

(see Figure 18 below).

10 Slide the system board tray assembly toward the front of the chassis, about 1/4 inch, and

then lift the system board up and out of the chassis (see Figure 19 below).

POWER SUPPLY - Type 2 SFF Chassis

1 If applicable, remove the security clip (see Figure 20 below).

2 Rotate the drive cage up and disconnect the power cables from all of the drives.

3 Release the power supply cable from the cable retaining clips on the bottom of the

chassis under the drive cage.

4 If applicable, disconnect the hood sensor from the system board and remove the sensor

from the power supply (see Figure 21 below).

5 Rotate the power supply to its full upright position, and then lift the power supply straight

up and out of the chassis (see Figure 22 below).

HP-00007-01, Appendix 3 04-Jan-2006

HP Restricted

Page 4

POWER SUPPLY PRINTED CIRCUIT ASSEMBLY

HP uses two different power supplies from two different vendors in these computers. Use the

following steps to determine which power supply you have and its required disassembly

procedures.

Power supply 1

1 Remove the six screws that secure the covers to the power supply

(see Figures 23 and 24 below).

NOTE: You do not need to remove the screws from the fan guard or the power

connector.

2 Cut the plastic cable clamp that secures the wires to the power supply cover

(see Figure 25 below).

3 Remove the covers from the power supply:

a) Slide the top cover to disengage the clips, and then remove the cover from the

power supply chassis.

b) Lift the side cover from the chassis.

4 Cut the following wires (see Figure 26 below):

- green/yellow wire

- blue and brown wires to the power outlet

- black fan wire (or unplug)

- main mass of wires (to gain access to capacitors)

5 Remove the three screws that secure the PCA to the power supply chassis

(see Figure 27 below).

6 Lift the PCA from the power supply chassis.

Power supply 2

1 Remove the nine screws that secure the covers to the power supply

(see Figures 28 & 29 below).

NOTE: You do not need to remove the screws from the fan guard or the power connector.

2 Cut the two plastic cable clamps that secure the wires to the power supply cover

(see Figure 29 below).

3 Remove the covers from the power supply:

a) Lift the top cover and slide to disengage the clips on the back.

b) Lift the side cover and slide back to disengage the clips on the bottom.

HP-00007-01, Appendix 3 04-Jan-2006

HP Restricted

Page 5

Power supply 2 (cont)

4 Cut the following wires (see Figure 30 below):

- green wire

- black wire

- white wire to power outlet

- fan wire

- main mass of wires (to gain access to capacitors)

5 Remove the four screws that secure the PCA to the power supply chassis

(see Figure 31 below).

6 Lift the PCA from the power supply chassis.

BATTERY

Locate the battery and battery holder on the system board. Depending on the type of battery

holder on the system board, complete the following instructions to remove the battery:

TYPE 1 BATTERY HOLDER (see Figure 32 below)

Lift the battery out of the holder.

TYPE 2 BATTERY HOLDER (see Figure 33 below)

To release the battery from its holder, squeeze the metal clamp that extends above one edge of

the battery. When the battery pops up, lift it out.

TYPE 3 BATTERY HOLDER (see Figure 34 below)

Pull back on the clip that holds the battery in place, and then remove the battery.

HP-00007-01, Appendix 3 04-Jan-2006

HP Restricted

Page 6

3.2 ILLUSTRATIONS

Figure 1: Type 1 SFF Chassis Figure 2: Type 2 SFF Chassis

HP-00007-01, Appendix 3 04-Jan-2006

HP Restricted

Page 7

FIGURE 3: Removing the computer cover

(SFF 1)

FIGURE 4: Removing the fan shroud (SFF 1)

FIGURE 5: Disconnecting cables from the

system board (SFF 1) FIGURE 6: Removing the security clip (SFF 1)

HP-00007-01, Appendix 3 04-Jan-2006

HP Restricted

Page 8

FIGURE 7: Rotating the power supply (SFF 1)

FIGURE 8: Disconnecting the serial port from

the system board (SFF 1)

FIGURE 9:Removing the system board

mounting screw (SFF 1) FIGURE 10: Removing the system board

(SFF 1)

HP-00007-01, Appendix 3 04-Jan-2006

HP Restricted

Page 9

FIGURE 11: Removing the security clip

(SFF 1) FIGURE 12: Removing the power supply

(SFF 1)

FIGURE 13: Removing the computer cover

(SFF 2)

FIGURE 14: Removing the fan shroud

(SFF 2)

HP-00007-01, Appendix 3 04-Jan-2006

HP Restricted

Page 10

FIGURE 15: Removing the security clip

(SFF 2) FIGURE 16: Disconnecting data and power

cables (SFF 2)

FIGURE 17: Removing the serial port (SFF 2)

FIGURE 18: Removing the long mounting

screw (SFF 2)

Altri manuali HP Scrivania

HP Kayak XU800 Series Come usare

HP dx7400 - Microtower PC Manuale utente

HP P Class 450/500/550/600/650/700/750 Manuale utente

HP Xw4200 - Workstation - 1 GB RAM Guida all'installazione

HP Pavilion a118 Manuale utente

HP s3600f - Pavilion - Slimline Istruzioni operative

HP Pavilion t100 - Desktop PC Manuale utente

HP Xw4550 - Workstation - 2 GB RAM Manuale utente

HP Compaq dx2400 Istruzioni per l'installazione

HP Workstation xw6000 Manuale operativo e di manutenzione

HP Compaq dx7200 MT Manuale utente

HP xw9400 Istruzioni per l'installazione

HP Pavilion p6210f Manuale utente

HP Net PC 20 Istruzioni utente

HP Presario S7000 - Desktop PC Manuale utente

HP Pavilion t600 - Desktop PC Manuale utente

HP EliteOne 800 G4 Manuale utente

HP Pavilion a1000 - Desktop PC Manuale utente

HP Z220 SFF Series Manuale

HP Pro All-in-One MS216br Come usare

HP Pavilion t410i Manuale utente

HP XM600 - Kayak - 128 MB RAM Manuale del prodotto

HP xw series Manuale utente

HP Z1 G2 Manuale utente

Manuali Scrivania popolari di altre marche

Asus

Asus E210 Series Manuale utente

Dell

Dell Inspiron 600m Manuale utente

Dell

Dell Inspiron 3662 Manuale utente

TotalFlow

TotalFlow uFLO Manuale utente

Logitech

Logitech MK320 Manuale utente

Dell

Dell XPS 730 H2C Manuale utente

Sony

Sony Vaio Series Manuale utente

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuale utente

Alto

Alto MD 250 Manuale utente

Lenovo

Lenovo ThinkCentre Edge 72 Manuale

Lenovo

Lenovo ThinkStation D20 Manuale

Arbor Technology

Arbor Technology FPC-7800 Series Manuale utente

Sony

Sony VAIO VGX-TP1 Series Manuale utente

Asus

Asus Eee Box B204 Manuale utente

Dell

Dell Optiplex 9010 All In One Manuale utente

Everex

Everex eXplora Manuale utente

Lenovo

Lenovo ThinkCentre M75e Manuale utente

Dell

Dell Alienware Area-51 R4 Manuale utente