HP 24WM Manuale utente
0
HP 24wm LED Backlit Monitor
User Guide
1
© 2015 Hewlett-Packard Development Company, L.P.
Microsoft, Windows, and Windows Vista are either trademarks or registered trademarks of Microsoft
Corporation in the United States and/or other countries.
The only warranties for HP products and services are set forth in the express warranty statements
accompanying such products and services. Nothing herein should be construed as constituting an
additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
This document contains proprietary information that is protected by copyright. No part of this document
may be photocopied, reproduced, or translated to another language without the prior written consent of
Hewlett-Packard Company.
First Edition (Feb. 2015)
Document Part Number: 805798-001
2
Chapter I. Introduction
1.1 Features
Multilingual OSD adjustment
Compatible with IBM VGA, extended VGA, VESA VGA, SVGA, XGA, and SXGAmodes
Wide range of applicable voltages (AC 100-240V 50/60Hz ) enables direct use without any
setting.
Plug-and-play VESADDC1/ 2B Standard. Compatible with Windows 9x / 2000 / XP / 7 / 8/Vista
operation systems
1.2 Check list
Please make sure the following items are included with your LCD monitor;
The monitor (and the pedestal)
Stand
Power cord
VGA cable
DVI cable (Optional)
Documentation and software Disc
Setup poster
Warranty
If any of these items are missing, please contact your dealer for technical support and custom
service.
Note: Be sure to save original box and all packing materials for future transport.
3
Chapter II. Installation
2.1 Install the pedestal
Please follow the steps illustrated below to install the pedestal.
4
2.2 Connect your monitor to your computer
1. Power off and unplug your computer.
2. Connect the 15-Pin ends of the signal cable to the VGA port of your monitor and the VGA OUT jack
on the back of your computer. Secure the screws on both ends of the signal cable.
3. Connect one end of power cord to the monitor, then connect the other end of the power cords to the
nearest electrical outlet.
4. Power on your computer and monitor. If your monitor displays an image, the installation has been
successfully done. If the monitor does not display any image, check all the connections.
Cautions: 1. For installation, please complete signal cord connection before plugging the power cord
into the electrical outlet to avoid damaging the monitor.
2. During installation, please support the front frame with your hand at its center of gravity to
avoid dropping and damaging the monitor.
Overview of the ports on the monitor:
1. AC power supply input
2. DVI signal input
3. VGA signal input
5
2.3 Disconnect the pedestal for shipping
Press the clip button on the pedestal and remove the pedestal from the stand.
6
Chapter III.Monitor overview
Overview of front panel controls
7
Chapter IV. Operational Instruction
4.1 Power ON/OFF Switch
Press this button to power on/off your monitor. Note: The ON/OFF switch does not disconnect your
monitor from the main voltage. To completely disconnect the main voltage, please remove the
power plug from the socket.
4.2 Power indicator
The power LED is blue when the monitor operates normally. If the monitor runs in power-saving
mode, this indicator changes to amber. When the monitor is turned off, this indicator is unlit.
4.3 Menu features
All the following features of your monitor can be accessed and adjusted by using the on screen
display (menu) system.
1. If your monitor is not powered on, press the "Power”button to turn it on.
2. Press the "Menu”button to activate the OSD menu. The OSD main menu will be displayed.
3. To view the main menu or submenu, press the “+” on the front panel of your monitor to scroll up
or the “-” to scroll down. Then press the "OK”button to select a highlighted function.
When the highlight scrolls down to the bottom of the menu, it returns to top of the menu. When the
highlight scrolls up to the top of the menu, it returns to bottom of the menu."
4. To adjust the selected option, press the “+” or “-” button.
5. Select “Save”and return. If you do not want to save the setting, select “Cancel”from the
submenu or “Exit”from the main menu.
6. Press the “Menu”button to exit from the OSD menu.
8
4.4 OSD operational instructions
Icon
Main menu
option
Submenu option
Note
Brightness
To adjust the brightness level of the
screen. The factory default range is
90.
Contrast
To adjust the contrast level of the
screen.The factory default range is
80.
Color
Selects the screen color.The
factory is 6500K or Custom
color,depending on the mode.
Warm- 5000K
Changes color to slightly reddish
white.
Standard- 6500K
Uses standard colors (default).
Cool- 9300K
Change color to slightly blueish
white.
Custom (RGB)
Selects and adjusts your own color
scales:
Red Color –sets your own red color
levels.
Green Color –sets your own green
color levels.
Blue Color –sets your own blue
color levels.
Image control
To adjust the image on the screen.
The ambient brightness sensor can
also be enabled or disabled (only
applicable to some models)
Auto-adjustment
To automatically adjust the image
on the screen (only applicable to
VGA input).
Clock and Phase
To adjust the clock phase of the
screen.
This adjustment eliminates all
horizontal noises to enable clearer
and more lifelike images and
9
characters (only applicable to VGA
input)
Horizontal position
To adjust the horizontal position of
an image (only applicable to VGA
input).
Vertical position
To adjust the vertical position of an
image (only applicable to VGA
input).
Custom Scaling
Selects the method on how
displayed information on the
monitor will be formatted.Select
Fill to Screen –image fills the entire
screen and may look distorted or
elongated because of
non-proportional scaling of height
and width.
Fill to Aspect Ration –image is
sized to fit the screen and maintains
proportional image.
Sharpness
Adjusts the screen image to look
sharper or soft. (range:1~6)
Dynamic Contrast
Turns Dynamic Contrast Ratio On
or Off.The factory default is Off.
OSD Control
Provides a menu for adjusting the
on-screen display(OSD)control.
Mode Display
The resolution, refresh rate and
frequency information will be
displayed when the OSD main
menu is accessed. Please select
“On” or “Off” as the factory default
on-off setting.
Monitor Status
The operational status of your
monitor will be displayed when you
power on your monitor. To select
the positions where the status
information is displayed:
Top
Middle
Bottom
Off
The factory default setting is “Top”
OSD position
To adjust OSD position for your
monitor.
Indice
Altri manuali HP Monitor
HP
HP Pavilion M70 Manuale utente
HP
HP 24wd Manuale utente
HP
HP V213a Istruzioni per il montaggio
HP
HP 2011x Manuale utente
HP
HP HC270cr Istruzioni per l'installazione
HP
HP 25mx Manuale
HP
HP L1945W - Promo Widescreen LCD Monitor Istruzioni utente
HP
HP Compaq LE2001wl Istruzioni per l'installazione
HP
HP S17X Manuale utente
HP
HP MX703 - Pavilion - 17" CRT Display Scheda tecnica
HP
HP Designjet 130 Series Manuale per l'uso e la cura
HP
HP Pavilion F1903 Manuale utente
HP
HP W19B Come usare
HP
HP L1902 Manuale utente
HP
HP D2846 Manuale utente
HP
HP Essential LE1901w Manuale utente
HP
HP E24i G4 Istruzioni per il montaggio
HP
HP EliteDisplay E222 Istruzioni utente
HP
HP A7217A - 24" CRT Display Manuale utente
HP
HP L1506 Manuale utente
