HP Fax 650 Manuale utente
Installation Guide
HP J2437A
4-Port Token Ring Interface
for the HP Router 650
© Copyright Hewlett-Packard Company 1994.
All rights reserved.
Publication Number
5962-8322
Edition 1, August 1994
Printed in USA
Product Numbers
This guide provides installation instructions for the following Hewlett-Packard Companyproduct:
J2437A
Warranty
The information contained in this guide is entirely unwarranted.
This document contains proprietary information, which is protected by copyright. No part of this document may be
photocopied, reproduced, or translated into another language without the prior written consent of Hewlett-Packard. The
information contained in this document is subject to change without notice.
Hewlett-Packard
8000 Foothills Boulevard
Roseville, California 95747-6588
916-786-8000
Introduction
The 4-Port Token Ring Interface provides four 4- or 16-Mbit/s
connections for connecting token ring networks to the HP Router 650.
Installation
Ensure that you have the following items.
1 LED label strip (J2437-80012)
5 Interface card labels (5182-3315)
1 Cable tie (5182-1723)
1 Grounding wrist strap (9300-1408)
1Installation Guide (this manual, 5962-8322)
1Caution: Static-Sensitive Devices (5962-8318)
Installation
Ensure that you have the following items.
3
Install interface card.
Notes You can install the interface card without taking the system offline (that
is, without switching the router off and taking all networks down)—
refer to “Installing the Interface Card (System Online),” page 9.
(Installing an interface card without taking the system offline is often
called “hot swapping.”)
If you are installing the interface card in a slot that formerly was empty,
or if you are installing the interface card in a slot that formerly held a
different type of interface card (such as a WAN interface card), you must
specify the new card in the configuration. (Refer to “Configure and boot
the router” in chapter 1 of the HP Router 650 Installation Guide.)
Installing the Interface Card (System Offline)
Note If you will be installing the new interface card in a slot where another
interface card is not currently installed, begin with step 2; otherwise,
begin with step 1.
1. Disconnect all cables from the interface card you will be removing,
and save them for reconnection when you later install that card again.
Installation
Install interface card.
4
2. Open the front door of the router by pulling its lock—the round post
at the upper right—to the right.
3. Switch the power supply off by pressing the bottom of its switch
(marked with “❍”). If two power supplies are installed, switch both
off.
4. Connect a grounding wrist strap (one is provided with the interface
card) to your wrist and to the back of the router.
Figure 1. Opening Router Door
Installation
Install interface card.
5
5. Press down slightly on the insides of both locks on the old card’s
bezel (see figure 2), then swing them outward until the bezel
disengages (see figure 3).
6. Grasping the left and right edges of the bezel, pull out until the tray is
about half exposed.
7. Grasping the sides of the tray, remove the card from the router.
8. Holding the new interface card by the sides of its tray, slide the back
of the tray about half-way into the router.
Figure 2. Unlocking Card Bezel
Figure 3. Disengaging Card Bezel
Installation
Install interface card.
6
9. Pull the locks on the bezel outward, then push evenly on both ends
until the card engages fully and the locks swing inward to about 45°.
10. Push the two locks evenly to close them, pressing downward slightly
to secure them in place.
11. Remove the old card’s LED label strip in the router door from the
position corresponding to the slot where you have installed the
interface card, then insert the LED label strip provided with the new
card as far as it will go.
12. Bend the end of the label strip toward the back of the router,
creating a 90° fold.
13. Switch on the power supply by pressing the top of the switch
(marked with “|”).
14. Close the router door.
Figure 4. Installing Interface Card
Installation
Install interface card.
7
15. To replace the label at the left of the slot that identifies the depart-
ment or site served by the interface card, slide it out from the right.
Position the new label with its shiny side facing the router, and slide
it in from the right. (Additional labels are provided in the router’s
accessories kit and also with each interface card.)
Swap 12
HP J2608A
ThinLAN
HP J2608A
Swap 12
Swap 12
Swap 1
12
Fail
Rx Tx
Self testCard
Self-test
12
Net
Fail
Rx Ins
Card
Reset Clear
Remove and insert label
from this edge
4T
Figure 5. Interface Card Label Location
Installation
Install interface card.
8
Installing the Interface Card (System Online)
Note If you will be installing the new interface card in a slot where another
interface card is not currently installed, skip steps 1 and 3.
1. Disconnect all cables from the interface card you will be removing,
and save them for reconnection when you later install that card again.
2. Connect a grounding wrist strap (one is provided with the interface
card) to your wrist and to the back of the router.
3. If the Swap LED on the interface card you will be removing is not on
(see figure 6), press the adjacent Swap button, and hold it until the
Swap LED turns on (about 1–5 seconds).
Swap 1
HP J2608A
ThinLAN
J2434A
4S
Figure 6. Swap Button and LED
Installation
Install interface card.
9
4. Press down slightly on the insides of both locks on the old card’s
bezel (see figure 7), then swing them outward until the bezel
disengages (see figure 8).
5. Grasping the left and right ends of the bezel, pull out until the tray is
about half exposed.
6. Grasping the sides of the tray, remove the card from the router.
7. Holding the new interface card by the sides of its tray, slide the back
of the tray about half-way into the router.
Figure 7. Unlocking Card Bezel
Figure 8. Disengaging Card Bezel
Installation
Install interface card.
10
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali HP Router di rete
HP
HP A-MSR20 Come usare
HP
HP 10500 series Manuale utente
HP
HP VSR1000 Manuale utente
HP
HP Pavilion 501 Manuale di istruzioni
HP
HP StorageWorks MPX200 Manuale utente
HP
HP 5920 Manuale utente
HP
HP StorageWorks N1200-320 Manuale utente
HP
HP a-msr Manuale utente
HP
HP ProCurve 1410-24G Manuale utente
HP
HP A8800 Series Manuale di installazione
HP
HP MSR930 Series Istruzioni per il montaggio
HP
HP MSR SERIES Manuale utente
HP
HP FlexNetwork MSR3044 Istruzioni per il montaggio
HP
HP MSR ASM Manuale utente
HP
HP MSR SERIES Manuale utente
HP
HP 1920 Gigabit Ethernet Switch Series Manuale utente
HP
HP J2600A Manuale utente
HP
HP FlexNetwork HSR6600 Manuale di installazione
HP
HP 5920 Manuale utente
HP
HP ProCurve 2510G Series Manuale utente
Manuali Router di rete popolari di altre marche
NETGEAR
NETGEAR FS526T - Switch Manuale utente
Korenix
Korenix JetNet 5710G Series Manuale utente
Automated Logic
Automated Logic ZN551 Manuale del proprietario
Cisco
Cisco ASR 1000 Series Manuale dell'operatore
EnGenius
EnGenius ESR-9710 Manuale utente
Cisco
Cisco 805 Series Istruzioni operative e di sicurezza