HP A3550A - High Availability Disk Arrays Model 20 Storage... Manuale utente

Hewlett-Packard Power Supply

Installation Guide

Hewlett-Packard power supplies are installable and replaceable. Areplacement or add-on power supply must be the same

type as the power supplies already installed in the array.

The locations ofthe power supplies in the 30-slot disk arrays are shown in Figure 1.

.

Figure 1.

Install a power supply by performing the following steps. Place a check in the appropriate oas the step is completed.

Step 1: Observe antistatic precautions

Apower supply is shipped with an ESD kit containing:

–ESDwriststrap

– ESDconductive sheet

oGround the ESDwrist strap to any unplated metal on

the disk arraychassis and fasten the strap to your wrist.

On 30-slot disk arrays, the ESD wrist strap can be

grounded to the metal edge above the rear retaining

screws.

Step 2: Prepare to install the power supply

oRemove the new power supply from its shipping carton

and place it on a suitable antistatic surface or the ESD

conductive sheet.

oPress the release button on the fan pack and carefully

swing the fan pack down.

The installation or removal and replacement MUST be com-

pleted and the fan pack closed within two minutes or the

disk array will perform a thermal shutdown.

Power

supply

Disk array rear view

Step 3: Install the power supply

The power supply can be installed with array power on if a

third power supply is beinginstalled to upgrade to a redun-

dant configuration.The arraywillnot operate with only one

functional power supply;two are required.

oLocate the slot where the power supply is to be

installed.

oRemove the filler panel or failed power supply.

oInstall the power supply as shown in Figure 2.

oPush the power supply into the disk array chassis until

an audible click is heard. When the power supplyis

properly installed,it cannot be removed without using

the black release latch.

oClose the fan pack by carefully swinging the fan pack

up and firmly pressing it onto the latch until there is an

audible click. When the fan pack is properly latched, it

cannot be opened without using the release button.

Figure 2.

Fan pack removed for clarity. It is not necessary

to remove the fan pack to remove the power supplies.

Manual Part Number

A3692-90001 E0897 Copyright © 1997

Hewlett-Packard Company

*PA3692-96001*

A3692-96001

Altri manuali per A3550A - High Availability Disk Arrays Model 20 Storage...

10

Questo manuale è adatto per i seguenti modelli

1

Altri manuali HP Alimentazione elettrica

Manuali Alimentazione elettrica popolari di altre marche

Monacor

Monacor PS-12CCD Manuale utente

VOLTIMA

VOLTIMA MagicBox 15 Manuale utente

Agilent Technologies

Agilent Technologies 6032A Manuale utente

Miller

Miller Auto Deltaweld 452 Manuale utente

BCP

BCP PUOUBK Foglio di istruzioni

HC

HC 2210 Manuale utente

Puls

Puls CT5.241 Manuale utente

OCZ

OCZ ZX1250W Manuale utente

iseg

iseg ECH 238 Manuale utente

Power

Power XXL A Series Manuale utente

Agilent Technologies

Agilent Technologies 6631B Manuale utente

Renogy

Renogy PHOENIX 300 Manuale utente

Epson

Epson Stylus Scan 2500 Manuale operativo

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuale utente

Puls

Puls MiniLine ML50.100 Manuale utente

Puls

Puls AS-Interface SLA4.100 Manuale utente

Kenwood

Kenwood PS-60 Manuale utente

Elmdene

Elmdene G1380xN-y-s Series Manuale utente