HP 20/700 Manuale utente

62114 1

HP Surestore Tape Library 20/700 and

10/180 A5599A DLT Tape Drive

Installation Instruction

(for HP field service use only)

NOTE: If you are intermixing DLT7000 and DLT8000 tape drives in your

library, ensure that your backup application is configured

appropriately. The DLT7000 drive is not forward read-capable and

may overwrite a tape written by a DLT8000 drive.

CAUTION: HP tape library drives are not customer installable or replaceable.

Any servicing, adjustment, maintenance or repair must be performed only by

authorized HP service-trained personnel.

Note to Customer Engineer: This installation may add new technology to

the library that older user’s guides do not address. Please remind the

customer that the latest user documentation is available from the HP

Customer Care website: http://www.hp.com/go/support.

■Materials Included

Table 1. Materials List

Part Quantity

I/I DLT8000 1

DLT8000 Quick Reference Guide 1

DLT8000 Tape System Product Manual 1

DLT8000 Differential Drive Assembly 1

SCSI Y Cable 1

SCSI Differential Terminator 1

SCSI Mounting Screws 4

Power Termination Jumper 5

SCSI ID Jumper 10

HP Product ID Label 1

62114 2

■Installation Notes

• Confirm with the customer System Administrator that the tape library can be powered

off.

• Observe proper power off and power on procedures, as described in the Installation

or Service Manuals.

• HP has the drive factory set the drive to differential operation.

• When you install a DLT8000 tape drive remove the Product ID Label, located on the

drive, and place it in the appropriate box on the Drive Location Label. The Drive

Location Label is located on the inside of the library door, just below the UL label.

62114 3

■Tape Library Attachment

Perform these procedures to install a DLT8000 drive in an 20/700 library:

Tools Required

•Phillips screwdriver

•3/16-inch nut driver

❑Remove shipping restraint

❑Install drive(s) in library

❑Attach Y-cable between the drive and library bulkhead

❑Attach interface cable to drive

❑Power-on drive

❑Configure DLT drive

❑Attach SCSI Terminator

❑Attach interface cable to host

62114 4

■Library Drive Attachment

Tape drives are shipped individually. Due to the size differences of the DLT and 9840

drives, there are a variety of ways of installing the drives. Typically, drive installation moves

from the bottom slot and up.

Refer to Figure 1 and the explanation below for the configuration rules for installing drives.

1. The first callout in Figure 1 shows that the uppermost drive slot in the drive column can only be a

DLT drive.

2. The second callout depicts the size ratio of the 9840 drives to the DLT drives. In size, two

9840 drives fit in the same space as three DLT drives.

3. The third callout shows this ratio again: three DLT drives fit in the same space as two 9840

drives.

4. The fourth callout depicts a mixture of 9840 and DLT drives.

You may also install six 9840 drives plus one DLT drive in a column, where the DLT

drive occupies the top drive slot.

The following table lists the available combinations for one drive column.

9840 DLT

010

62114 5

Figure 1. Tape Drive Installation Guidelines

Tape Drive Installation Guidelines (H_53393)

1. DLT drive only in this position

2. Two 9840 drives (shown) or three DLT drives

3. Three DLT drives (shown) or two 9840 drives

4. Mixed 9840 and DLT drives (shown), three DLT drives, or two 9840 drives

NOTE:This graphic depicts the size relationship between DLT and 9840 drives ONLY.

Installation instructions call for installing the 9840 drives in the bottom slots, and the

DLT drives in the upper slots.

62114 6

■Installing DLT Drives

For DLT drives, follow the procedure below to unpack and install the drives.

DLT tape drives are shipped with the following, non-selectable configurations:

•DLT8000 (manufacturer’s model number)

•Differential operation

Refer to Figure 2 and make sure that the labels on the drive match the drive type and

operation required.

NOTE:Check with the customer for their maintenance agreement on tape drives. If

the customer agreement is to return the drives for repair, have them retain

one shipping box, with packing material, to be sent back to the factory.

Figure 2. DLT Labels

DLT Labels (H_65115)

1. Manufacturer’s model number label

2. Differential label (and drive serial number)

62114 7

NOTE:Refer to Figure 3 for the following procedure.

CAUTION: DLT equipment damage: Do not move the load latch of a tape drive by

hand until told to do so in later instructions.

1. Open the drive access section of the library (at the right side, as viewed from the front of

the library) by lifting up on the two latches. Turn the latches counterclockwise and open

the side door.

2. Open the drive package.

3. Remove the packing material.

4. Refer to Figure 3 while checking the side of the DLT drive for the terminating power

jumper selection.

CAUTION: Loss of data or degradation of performance: HP recommends

supplying terminating power (TERMPWR) from devices attached at both ends of

the SCSI bus. Industry standards advise that no more than three devices provide

terminating power to the bus.

Verify whether TERMPWR for DLT drives is on or off (enabled or disabled) for each

tape drive. If needed, move the jumper to match your requirement.

•TERMPWR On: Install the jumper on the pins shown in the following figure.

•TERMPWR Off: Remove the jumper on the pins shown in the following figure.

You can store the strap by placing it on one pin only.

NOTE:You may need to remove the DLT drive from its library tray to gain

access to this jumper. If removal is required, carefully turn the drive

upside down and remove drive mounting screws. Change the jumper

as required. Replace the drive mounting screws.

5. Carefully place each drive near the rear slots at the right side of the library.

62114 8

6. Look inside the drive column area and determine the slot you wish to use for each drive.

Following the lifting procedures described in Chapter 2 “Safety and ESD”, of the Instal-

lation Manual firmly grasp the drive at the rear with one hand and place the other hand

under the drive mounting plate.

7. Carefully guide the drive into its slot. Push it in as far as it will go and firmly seat the

drive.

NOTE:In the following step, do not over tighten the thumbscrew.

8. Refer to Figure 4 and turn the thumbscrew clockwise until it is secure.

Figure 3. Terminating Power Jumper DLT Drive

Terminating Power Jumper—DLT Drive (H_65116)

1. DLT drive

2. Load latch

3. TERMPWR jumper (enabled)

62114 9

Figure 4. Tape Drives Rear View

Tape Drives—Rear View (H_65124)

1. DLT power switch

2. Thumbscrews

3. 9840 power switch

62114 10

■Installing DLT Cable Connectors

The following procedures describe how to install the tape channel connectors for the tape

drives.

Standard Drive Column 0 Connectors.

NOTE:Drive column 0 is the standard drive column included in all libraries. It is

the column that contains the calibration label at the bottom. Also, some

of the following steps may require two people.

1. Go to the rear of the library, open the door, and locate the connector bulkhead.

2. Remove the SCSI “Y”channel cable and mounting screws from the drive box.

3. Refer to Figure 5 and insert the two channel connectors into the slots on the interior library

bulkhead, next to the desired drive location.

4. From the rear bulkhead, thread the four mounting screws into the connectors.

5. Tighten the mounting screws with a 3/16-inch nutdriver.

6. Insert the single connector end into the DLT drive.

7. Repeat these steps for all drives in column 0.

8. When you are finished installing all drives, place the drive power switch(es) to the ON (|)

position.

9. Close the rear door.

Figure 5. Tape Drive Cable Connectors

Tape Drive Cable Connectors (H_65226)

1. Interior bulkhead view

2. Exterior bulkhead view

Altri manuali per 20/700

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali HP Magazzinaggio

HP AJ765A - StorageWorks RDX Removable Disk Backup... Manuale di istruzioni

HP StorageWorks XP12000 Manuale utente

HP D2D Manuale utente

HP P2000 G3 Manuale utente

HP d212 Manuale utente

HP Surestore Disk Array 12h - And FC60 Manuale utente

HP EVA P6000 Manuale di servizio

HP C5658A - SureStore DLT 70e Tape Drive Manuale utente

HP C7745NB - SureStore DLT Tape Autoloader 1/9 Manuale utente

HP StorageWorks ESL E-Series Manuale utente

HP StorageWorks 2000 Series Manuale utente

HP 705 Guida rapida

HP XP7 Manuale utente

HP Surestore Tape Library Model 6/100 Manuale

HP Storevirtual 4000 Manuale utente

HP StorageWorks 8000 - NAS Manuale utente

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Manuale di istruzioni

HP FC 60 Manuale

HP Storevirtual 4000 Manuale utente

HP Alletra 4120 Istruzioni per il montaggio

HP Surestore 6164 - Switch Manuale utente

HP StorageWorks Ultrium 230 Manuale

HP Storevirtual 4000 Guida di riferimento rapido

HP Storevirtual 4000 Manuale utente

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente

Dell

Dell PowerVault MD3600f Series Manuale utente

CFI

CFI TERA STOR SATA RAID IV Manuale utente