HP Designjet 220 Istruzioni utente

hp surestore

tape library

2/20, 4/40, 6/60

setting up your library

SCSI Interface Cable(s): Four-meter SCSI cable(s)

with 68-pin connectors.

SCSI Terminator(s): 68-pin SCSI terminator (HVDS

or LVDS) to terminate the SCSI chain.

Fibre Channel Cable: Optical short-wave cable that

connects the Fibre Channel card to the host, hub,

or switch (for Fibre Channel configurations).

Fibre Channel GBIC: Connects the Fibre Channel

cable to the host, hub, or switch (for standard

performance Fibre Channel controllers only).

SCSI Jumper Cable(s): 68-pin cable that connects

the library controller or Fibre Channel card to a

drive.

Tape Cartridges: Cartridges included for data

backup.

Cleaning Cartridge: Cleaning cartridge to be used

when cleaning the drive.

Power Cord(s): Localized power cord(s) included

with the library.

User's Guide: Describes installation, operation, and

troubleshooting information.

Installation Poster: Provides an overview on

installing and configuring the library, as well as

additional information on support.

Trim Brackets (field rack only): Aligns the library to

the depth of the rack.

Host Interface Card: Install into the host system as

needed for your configuration.

Bar Code Label Kit: Bar code labels for data and

cleaning cartridges, and reordering information.

Library Accessories

Depending on the configuration, the following accessories may be shipped with the library.

Contact your support or service representative to obtain additional parts.

Install Rack Components

Install the clip nuts and mounting rails.

Ensure there is enough clearance between

the top and bottom rails for the library.

Note: The terms 20-slot, 40-slot and 60-slot

indicate maximum drive and slot capacity

for the library.

Install the Library into a Rack

Position the library so that

the side of the library faces

the front of an appropriately

rated mechanical lift. Align

the back of the library to the

rack and begin turning the

lift's hand crank until the

library is at the desired

height. Gently slide the

library into the rack.

Tip: To reduce the weight of the library, you can

remove all the drives.

Note: The 20-slot library can be safely installed by

two people without using a lift.

20-slot

60-slot

40-slot

Follow these steps to get connected in minutes. Depending on the configuration ordered, some of these steps may

have been completed at the factory. For users unfamiliar with storage devices, please refer to the user guide for the

library. Note: Your library model might look different from the illustrations used on this poster.

Install Library Components

Depending on your library

configuration, install the Fibre Channel

card(s) and drive(s).

Check the Host Configuration

Ensure that the host system has the

appropriate number of card expansion

slots and host interface cards for your

library configuration. For more

information on cabling, refer to Steps 5

and 6. For more information on

installation, refer to the user guide for

the card.



Connect the Library (SCSI)

Install the SCSI interface cables

and terminators. Refer to chapter

1 of the library User's Guide for

additional cabling information.



Connect the Library (Fibre

Install the SCSI interface cables

and terminators to the drives and

Fibre Channel cards. Refer to

chapter 1 of the library User's

Guide for more information on

cabling.

Connection for remote management

68-pin SCSI cables

Connection for remote management

68-pin SCSI cables68-pin SCSI cables68-pin SCSI cables68-pin SCSI cables68-pin SCSI cables

68-pin

SCSI terminators

Fibre channel connection

to hub, switch, or host

High-density

SCSI terminators

Configure the Library and

Power on the Host

Use the standby switch to power on

the library. If this is a Fibre Channel

installation, configure the library before

connecting it to the Fibre Channel

topology. (Refer to chapter 3 of library

User's Guide.)

Important: If you are using

Fibre Channel, power up in this order:

library, hub and/or switch (if applicable),

and then the host.

Install and Configure the Host

Drivers and Backup Software

(Refer to the backup software documentation for

more information.)

To verify that the host and library

are connected, look for the library's

SCSI ID on the host when the host is

powered on. You can also use HP

Library & Tape Tools (available from

www.hp.com/go/support) to ensure

the host and library are

communicating.

Run a test backup to ensure the

host, backup software, and library

are correctly configured.

Standby Switch

Getting Started

Post-Installation Configuration Tasks

Complete these tasks on the library's front panel during the initial setup.

Refer to Chapter 3 of the library User's Guide for more information.

Date and Time: When you first set up the library or if it is disconnected for an extended period of time,

you must set the real-time clock.

Mailslot: The library is initially configured for a one-slot mailslot. You can also select no mailslot, a

five-slot mailslot, or a ten-slot mailslot. The mailslot allows zero, one, five, or ten slots to be

reserved. When configuring the mailslot, ensure that the slots that will be reserved for the mailslot

are empty and that you reconfigure the host to recognize this configuration.

Password: The library does not have a password enabled when it arrives. For additional security,

enable and select a password.

Remote Access: You can monitor and manage your library anywhere on the network through user-

friendly web pages. You will need to configure the library using DHCP or by entering the IP

address, subnet mask, and gateway address. You must enable and select a library password and

then use that same password to configure the library remotely.

Note: The library has a mixed media feature that allows the use of two drive technologies in the same

library. For more information, refer to Appendix D in the library User’s Guide.

Information Roadmap

Support and Product Information: www.hp.com/go/support

TASK INFORMATION LOCATION

Installing the Library Library User's Guide, Chapter 1

This installation poster

Operating the Library Library User's Guide, Chapter 2

(opening doors, loading tapes and magazines)

Configuring the Library Library User's Guide, Chapter 3

Monitoring the Library Web-Based Library Adminstrator web pages

Library User's Guide, Chapter 3

Retrieving Library Performance Web-Based Library Adminstrator web pages

Library User's Guide, Chapter 3

Information About Library Components Front Panel INFORMATION menu

Library User's Guide, Chapter 3

Troubleshooting & Diagnostics Error codes on the library front panel

Troubleshooting table in the Library User's Guide, Chapter 4

Upgrading My System Library User's Guide, Chapter 4

(adding drives, downloading firmware)

Service and Support Library User's Guide, Appendix C

Running Internal Library Tests Library User's Guide, Chapter 4

Host Interface Card and Driver Installation Host interface card documentation and included disks

Hub, Switch, or Host Configuration Hub, switch, or host computer documentation

Drives and Media Library User's Guide, Appendix D

Front Panel Overview

The front panel is the control device for the

library. This LCD display typically provides a

status line at the top, up to five lines of text,

and a soft-key line at the bottom.

1 Front Panel Display

2 Tape Drawer with Lock

3 Soft Keys

4 Viewing Window

5 Power (Standby) Switch

Rear Panel Overview

This illustration depicts the standard fibre

channel configuration with six drives. If your

library is configured without Fibre Channel,

slot #4 will be vacant.

1 Vacant Slot

2 Remote

Management Card

3 Library Controller

Card

4 Fibre Channel

Controller Card (if

using Fibre Channel)

5 Drive Module 1

6 Drive Module 2

7 Drive Module 3

8 Drive Module 4

9 Drive Module 5

10 Drive Module 6

11 Power Supply

12 Slave Controller

Card

13 Product Information

Labels

Data subject to change

Printed in USA 12/2000

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali HP Magazzinaggio

HP P9000 Aggiornamento firmware

HP StorageWorks 2100 - Disk System Manuale utente

HP C7745NB - SureStore DLT Tape Autoloader 1/9 Manuale utente

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Manuale di istruzioni

HP StorageWorks P4000 Series Aggiornamento firmware

HP StorageWorks P4000 Series Manuale utente

HP EVA P6000 Manuale utente

HP DW017B - StorageWorks Ultrium 448 Tape Drive Manuale di istruzioni

HP 3PAR StoreServ 7000 Manuale utente

HP D2D Manuale utente

HP HPE StoreEasy 1000 Manuale utente

HP Open View Manuale del prodotto

HP StorageWorks MSL6000 series Manuale utente

HP mv2040 Manuale utente

HP StorageWorks 70 Come usare

HP Cray CS E1000 Istruzioni per l'installazione

HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard... Guida

HP P9000 Manuale utente

HP StorageWorks 1500cs - Modular Smart Array Manuale utente

HP Pavilion p6000 - Desktop PC Manuale utente

HP Surestore 6164 - Switch Manuale utente

HP 40 SCSI Istruzioni utente

HP StoreEver ESL G3 Manuale utente

HP SimpleSave Manuale utente

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente

Dell

Dell PowerVault MD3600f Series Manuale utente

CFI

CFI TERA STOR SATA RAID IV Manuale utente