HP Surestore 1200ex - Optical Jukebox Manuale utente

Adding 2 Drives to the

C1107 Series Jukebox

HP Part No. C1158-90001

Printed in USA February, 1998

Edition 2 0298

*A utility to download the code - SCSI Pro from CoComp or SCSI Toolbox from

*A PC with a SCSI interface and appropriate cables

Important! Read This First

BEFORE starting this upgrade, obtain the following:

*The downloadable code required for this upgrade. Obtain this code

from www.hp.com/isgsupport/optical/fw/ﬁrmware.html

This upgrade requires code to be downloaded to the controller PCA and the drives.

Peripheral Test Instruments (PTI).

Hewlett-Packard Company, 1998

Adding 2 Drives to the C1107 Series Jukebox

ESD Precautions

The optical disk jukebox contains very sensitive electrical components. It is EXTREMELY IMPOR-

TANT that you follow the proper procedures for preventing ESD (Electrostatic Discharge). Use wrist-

grounding straps, anti-static mats, and anti-static work stations when removing and replacing the

major assemblies.

a. If you want to add more than one drive upgrade to the C1104F/G/H, you must ﬁrst install a capacity

upgrade( C1159F/G/H). Installing a capacity upgrade gives the product a C1107F/G/H conﬁguration.

Before Upgrade... ..using 1, 2, or 3 drive

upgrade kits (2 drives/kit) Upgraded to equivalent of:

(# of drives)

Half-capacity conﬁgurations:

C1104F/G/H (4 drives) 1 kit C1105F/G/H (6 drives)a

Full-capacity conﬁgurations:

C1107F/G/H (6 drives)

C1108F/G/H (8 drives)

C1110F/G/H (10 drives)

1 kit C1108F/G/H (8 drives)

C1110F/G/H (10 drives)

C1112F/G/H (12 drives)

C1107F/G/H (6 drives)

C1108F/G/H (8 drives) 2 kits C1110F/G/H (10 drives)

C1112F/G/H (12 drives)

C1107F/G/H (6 drives) 3 kits C1112F/G/H (12 drives)

Table 1: Drive Upgrade Options for the C1107 Series Jukebox

Caution

Failure to follow proper procedures could lead to intermittent

failures and/or premature hard failures in the disk controller

and mechanism.

Tools Required

The following tools are needed for assembly/disassembly of the autochanger:

• Torx driver with the following bits: T-10, T-20

Kit Contents

Check the conversion kit to make sure you have the following parts:

• 2 - 4X drives — # C1113-60x00

• 1 - drive interface cable — # C1107-60x63

• 1 - drive power cable — # C1107-60x55

• 1 - drive SCSI cable — # C1107-60x46

• 2 - drive interface cable clamps — # 1400-0611

• 1 - capacitive load (terminator) - C1108-61600

• 1 - drive bracket air seal — # C1107-80604

• 10 - M3x6 T10 screws — # 0515-2382

• 2 - product upgrade label sheets (Upgrade to: ) — # 5181-9902

• 1 - these instructions

Note

This document is not necessarily revised as each part number

is revised.

In the above list, an “x” is placed in “service” part numbers

(parts orderable from Support Materials Organization) to

designate that this digit increments when the part is revised.

This digit usually starts at “0” and increments up to “9.”

Knowing this should help you locate the correct part at SMO.

For any other parts that may be missing from this kit, contact

your supplier.

Before You Begin

1. Look in the jukebox front "window" and make sure that there are no disks in any drive.

Use the control panel to eject any disk still in a drive

2. Bring the jukebox “down.”

Procedures for bringing this jukebox ofﬂine depend on the speciﬁc host system. Coordinate with

the system administrator to prepare this jukebox for the upgrade. This may involve “downing” the

host system also.

3. Remove power from the jukebox.

4. Disconnect the SCSI interface from the host.

Caution

Do NOT switch off power to the jukebox until you are sure the

SCSI bus is inactive. Switching off the jukebox when the

SCSI bus is active can cause data loss and/or indeterminate

bus states.

When doing this upgrade, be sure that disk cartridges are not

moved from their original slot locations. If you need to remove

the cartridges, record their SLOT LOCATIONS and

ORIENTATION so they can be replaced to their ORIGINAL

positions. Failure to follow this practice results in a serious

loss of ﬁle system integrity.

Installing the 2-Drive Upgrade

Note

There are 2 drives installed in each drive enclosure.

If you are upgrading a 1/2-capacity conﬁguration jukebox

that has 4 drives, you will currently be using the top 2 drive

enclosures, and will add 2 drives to the drive enclosure that is

3rd from the top.

If you are upgrading a 1/2-capacity conﬁguration jukebox

with 6 drives, you must add the capacity upgrade (C1159F/G/

H, which includes 3 empty drive enclosures) at the same time

that you add the drive upgrade.

If you are adding two drives to a full conﬁguration with 6, or

10 drives, install the drives in the ﬁrst available empty drive

enclosure from the top. DO NOT skip drive mounting

locations. See the right-hand box in Figure 1.

If you are upgrading to a 10-drive unit, move the drives at

position #3 down to position #5, move the fan at position #5

up to position #3, and add the new drives in position #6.

Enclosure #3 must not contain drives. Positioning the drives

in this way in a 10-drive upgrade matches the way 10-drive

jukeboxes ship from the factory after February, 1998. This

conﬁguration enables future connection into a high-

availability environment if requested by the customer. See the

left-hand box in Figure 1.

Figure 1: Drive locations in 8-, 10-, and 12-drive upgrades

1. Remove the 3 right-side panels.

The side panels have 2 T-20 screws on the bottom edge. Start from the bottom panel ﬁrst.

Figure 2: Screws on side and rear panels

2. Remove the two RFI panels .

There are 6 T-20 screws around the edge of each panel.

Figure 3: Lower and upper RFI panels

3. If upgrading to an 8- or 12-drive conﬁguration, remove the ﬁrst available (empty) drive enclosure

from the top. If upgrading to a 10-drive conﬁguration, remove the drive enclosure at position #6

(see Figure 1).

a. Disconnect the fan power cable from the interposer PCA.

b. Remove the 2 T-20 screws from each side of the drive enclosure and remove the drive enclo-

sure.

4. Remove the top cable access panel on the top rear of the drive enclosure.

The access panel will rotate out if the 2 T-10 mounting screws on either side of the enclosure are

removed.

5. Place the (empty) drive enclosure on its side and trim off the top half of the cable hole edge protec-

tor. Use a utility knife to cut through the middle of each side of the edge protector. Remove the top

half. See Figure 4.

Cutting off this portion of the edge protector allows the L-shaped air seal that will be mounted later

to stick,

Figure 4: Cutting off the top half of the cable hole edge protector

6. Check the DIP switches on the top of the drives. Make sure they are set to OFF, which is in the

forward position (toward the front of the drive.) Refer to Figure 5 for DIP switch location and

orientation on the top of the drives.

Figure 5: Orientation of the drive DIP switches

7. Install drives in the drive enclosure.

a. Mount the drive interface cable clips on the cable as shown in Figure 6.

Figure 6: Attaching cable clips to the (double) drive interface cable

Altri manuali per Surestore 1200ex - Optical Jukebox

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali HP Magazzinaggio

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Manuale di istruzioni

HP Storevirtual 4000 Manuale di istruzioni

HP 330834-B21 - StorageWorks Ultrium 460 Tape Library Drive... Manuale utente

HP Ultrium 1840 Manuale utente

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Manuale di istruzioni

HP StorageWorks DLT 80 Istruzioni utente

HP StorageWorks 12000 Manuale utente

HP C7745NB - SureStore DLT Tape Autoloader 1/9 Manuale utente

HP StorageWorks SB920c Tape Blade Istruzioni per il montaggio

HP STORAGEWORKS ALL-IN-ONE STORAGE SYSTEM Manuale utente

HP StoreOnce 3100 Manuale

HP 418371-B21 - Dual Port 72 GB Hard Drive Manuale utente

HP StorageWorks 8000 - NAS Manuale utente

HP StorageWorks 2012i Manuale utente

HP StoreEver MSL3040 Manuale

HP LeftHand P4000 - SAN Solutions Manuale di istruzioni

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Manuale di istruzioni

HP Storevirtual 4000 Manuale utente

HP StorageWorks XP10000 - Disk Array Manuale utente

HP StorageWorks 8000 - NAS Manuale utente

HP StoreVirtual P4000 G2 Manuale di servizio

HP StorageWorks RDX160 Istruzioni utente

HP Pavilion p6000 - Desktop PC Guida

HP Ultrium Drive Manuale del prodotto

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente

Dell

Dell PowerVault MD3600f Series Manuale utente

CFI

CFI TERA STOR SATA RAID IV Manuale utente