HS-Technik RoboRiv Manuale utente
OPERATINGINSTRUCTIONS
RoboRiv ®
Issue date: April 2020
Tool Firmware: from 2.2.5.18
HST-Tool-Manager: from 2.0.5.4
Note
In case of doubt, the original German version of
- 2 -
Table of contents
PAGE
4
PAGE
12
PAGE
15
PAGE
18
1 Operang principles
1.1 Scope of delivery 4
1.3 Signs and symbols used 6
1.4 Structure of the warnings 7
1.6 Intended use 8
1.7 Improper use 8
1.10 Training of personnel 10
1.11 Guarantee and liability 10
1.12 Copyright 11
2 General safety informaon for power tools
2.1 Use and handling of power tools 12
2.3 Service 14
3 Important informaon about this tool
3.4 Cleaning the device and disposal 17
4 Start-up and use
4.2 Assembly of the RoboRiv 20
4.4.2 LED indicator at the back and sound signals 24
4.4.3 OLED Display 25
4.4.4 Selection of threaded mandrel and mouthpiece 26
4.4.5 Adjusting the mouthpiece 27
4.4.6 Tool start 28
4.4.7 Set blind rivet nuts 28
4.4.8 Unwinding 30
4.4.10 Use of tools and maximum load 31
4.5 Display 32
4.5.1
4.6 HST-Tool-Manager 37
4.6.1 Setup 40
- 3 -
PAGE
52
PAGE
54
PAGE
55
PAGE
56
PAGE
57
PAGE
58
PAGE
59
PAGE
60
4.6.5 Management 43
4.6.7 Signals 45
4.8.3 Machine capability test (MCT) 50
4.8.4 Service interval counter 51
5 Interfaces
5.1 Power Supply 52
5.2 Serial port 52
5.3 IO Ports 52
6 Storage
7 Technical data
8 Drawings
9 Troubleshoong and Fault repair
Declaraon of conformity in accordance with the electromagnec
compability direcve 2014/30/EU
EC Declaraon of Incorporaon according to Machinery Direcve 2006/42/
EC, Annex II, 1. B
Annex to the declaraon of incorporaon for incomplete machines
according to 2006/42/EC, Annex II, 1 B
- 4 -
1 Operang principles
Dear customers,
Thank you for choosing a HS-Technik GmbH product.
This quality product „Made in Germany“ fulfils the highest requirements with regard
to performance, quality and accuracy. When used correctly the product will definitely
perform very well for many years.
These operating principles contain information on safety and for the operation of the
tool. In addition it contains information on the dimensions and technical data. We would
be happy to assist you with additional information or to answer your questions. Our
technical support and our technicians would be happy to assist you.
1.1 Scope of delivery
• Cordless blind riveting tool
• Power supply unit for power supply
• USB Cable (Type A on Mini B)
• Operating instructions
1.2 General informaon
Read the operating manual before initial operation. Please pay particular attention to
Chapter 2 „General safety information“.
This manual should make it easier for the operator to get to know the tool and to make
use of its intended application possibilities. The operating instructions include important
information related to the safe and proper operation of the tool. Compliance with these
instructions helps you to:
• Avoid dangers
• Avoid repair costs and downtimes
• Increase the reliability and the lifespan of the product.
- 5 -
This manual must be read and applied by every person who is assigned to conduct work
using this tool.
In addition to this operation manual the applicable regulations on accident prevention
and environmental protection should be observed.
NOTE
After reading, keep the operating manual in a place accessibly to every
operator. If you have any further questions, please feel free to contact us.
- 6 -
1.3 Signs and symbols used
The following signs and symbols will be used in this manual, or on the product:
Symbol Explanaon
Do not dispose of with household waste
EU conformity marking
®Registered trademark
Use only indoors
Intrinsically safe transformer
Direct current
Universal Recycling Symbol
- 7 -
1.4 Structure of the warnings
The warnings are structured as follows:
DANGER
Indicates an immediate dangerous situation that can lead to serious or even
WARNING
Indicates a potentially dangerous situation that can lead to serious injuries
NOTE
Important and useful information on using this tool.
1.5 Technical terms and abbreviaons used
Abbreviaon Meaning
°C Degrees Celsius, temperature
AC
Ah
ahv
dB(A) Decibels, sound pressure level (A-weighted)
DC Direct current
Hz Hertz, Frequency
Li-Ion
LpA Emission sound pressure level, workplace-related
min-1
mNN Metres above sea level, height
- 8 -
Abbreviaon Meaning
SN Serial number
W
1.6 Intended use
controller is required to operate the RoboRiv.
The tool may only be used for this purpose as described in this manual. Only materials that
are suitable for this type of tool may be used.
WARNING
Intended use also includes
• following all indications of the operating instructions and
• observance of inspection and maintenance works.
Any other use or use beyond that is considered improper use. HS-Technik GmbH is not
1.7 Improper use
DANGER
The use of this tool for other purposes, e.g. for hammering, is not permitted.
Improper use or incorrect accessories can lead to dangers with unforeseeable
consequences.
We accept no liability for damage and malfunctions resulting from non-observance of
these operating instructions and improper use.
1.8 Dues of the operator
the tool at the workplace to work with this tool.
The safety awareness of the personnel while working will be reviewed at regular intervals.
1.9 Dues of personnel
Prior to its use all people who work with this tool are obligated to inform themselves of
and to observe them.
- 10 -
1.10 Training of personnel
the supervision of an experienced person.
1.11 Guarantee and liability
Guarantee and liability claims for personal injury and property damage are excluded, if
caused by one or more of the following:
• improper use
-
• improperly performed repairs
Indice
Altri manuali HS-Technik Utensili per rivetti
