Huawei YDS60-80 Manuale utente

YDS60-80 Smart Power Sensor

Quick Guide

Issue: 02

Date: 2022-08-20

1Overview

Specifications on the front panel

YDS60-80

The dimensional tolerance is ±1 mm.

Nameplate

Dimensions

Appearance

1.2

1.1

Installation

position

Category YDS60-80

Nominal voltage 230 V AC/400 V AC, 50 Hz/60 Hz

Current measurement range Direct connection: 0–80 A

Connection through current transformers: > 80 A

Voltage measurement range 90–1000 V (line voltage; potential transformers are required

if the voltage is greater than 500 V)

Electricity metering accuracy Class 1 (error within ±1%)

Power grid system Three-phase four-wire or three-phase three-wire

Baud rate 4800/9600/19200/115200 bps (default value: 9600 bps)

Operating temperature –25℃to +60℃

Installation mode Guide rail-mounted

Certification CE, RCM, and UKCA

Key Specifications

1.3

•Input voltage: When the line voltage is less than or equal to 500 V, connect the meter

directly. When the line voltage is greater than 500 V, connect the meter through potential

transformers.

•Input current: When the input current is 0 A to 80 A, connect the meter directly (channel 1).

When the input current is greater than or equal to 80 A, connect the meter through current

transformers (channel 2).

Port Definition

1.4

Cable Inlet Cable Outlet

1.4

2Installing the YDS60-80

1. Install the Smart Power

Sensor on the standard

guide rail of DIN35mm.

2. Press the Smart Power

Sensor downwards onto

the guide rail, and then

push it in place along

the guide rail.

Cable Port Type

Conductor

Cross-

sectional

Area Range

Outer

Diameter Source

Channel 1

voltage

cable

Ua IN and OUT Single-core

outdoor copper

cable

25 mm210 mm

Prepared by

the customer

Ub IN and OUT

Uc IN and OUT

Un IN and OUT

Channel 2

voltage

cable

Ua IN Single-core

outdoor copper

cable

4–25 mm25–10 mm

Prepared by

the customer

Ub IN

Uc IN

Un IN

Channel 2

current

transformer

cable

Ia*

Single-core

outdoor copper

cable

2–4 mm23–5 mm

Prepared by

the customer

or supplied

with current

transformers

Ib*

Ic*

Communications

cable

RS485A

wo-core

outdoor

shielded twisted

pair copper

cable

0.25–1.5

mm24–11 mm

Supplied by

the

manufacturer

RS485B

3Installing Cables

3.1 Preparing Cables

The maximum torque of Ua, Ub, Uc and Un terminal screws is 1.7 N·m, and the

recommended torque is 0.9–1.1 N·m. The maximum torque of Ia*, Ia, Ib*, Ib, Ic*, Ic, RS485A

and RS485B terminal screws is 0.4 N·m, and the recommended torque is 0.15

–

0.25 N·m.

Current ≤ 80 A > 80 A ≥ 0 A

Line voltage ≤ 500 V > 500 V

Connection

mode

Current and voltage

direct connection

Connection through

current transformers and

voltage direct connection

Connection through current

transformers and p

otential

transformers

Connection

setting

Direct connection:

SPEC = 1 (default)

Connection through transformers:

SPEC = 0

Current

transformation

ratio

CT = 1

(default)

CT = Ratio of the installed

current transformer

Potential

transformation

ratio

PT = 1.0

(default)

PT = Ratio of

the installed

potential transformer

Wiring

mode

3P4W:

net = n.34

(default)

3P3W:

net = n.33

3P4W:

net = n.34

(default)

3P3W:

net = n.33

3P4W:

net = n.34

(default)

3P3W:

net = n.33

3.2 Wiring Scenarios

•You need to set parameters after cable connections are complete. For details, see section 4

"Display and Parameter Settings".

•This meter is generally used in commercial and industrial high-current scenarios. In external

CT scenarios, the precision of the secondary-side current is ±5 mA. For example, if a CT with

a transformer ratio of 400/1 is selected, the error is ±2 A. This meter is not recommended

in scenarios where the plant power is low or the control precision of the grid-connection

point is high. Instead, use a meter with higher precision.

Current and Voltage Direct Connection (Current ≤ 80 A and Line

Voltage ≤ 500 V)

3.3

•Three-phase four-wire

connection

•Three-phase three-wire connection

(1) Shield layer of the signal cable

You need to set parameters after

cable connections are complete.

For details, see section 4 "Display

and Parameter Settings".

SmartLogger networking

In the SmartLogger

networking scenario, the

power meter is connected to

the SmartLogger. In the non-

SmartLogger networking

scenario, the power meter is

connected to the inverter.

•Three-phase four-wire connection

•Three-phase three-wire connection

(1) Shield layer of the signal cable

You need to set parameters after

cable connections are complete. For

details, see section 4 "Display and

Parameter Settings".

Smart Dongle networking

Please ensure that the

ground cable is installed

securely. Poor grounding

may cause electric shocks.

Connection Through Current Transformer and Voltage Direct

Connection (Current > 80 A, Line Voltage ≤ 500 V)

3.4

•You need to set

parameters after

cable connections

are complete. For

details, see section 4

"Display and

Parameter Settings".

•For the three-phase

three-wire

connection, phase B

does not need to

connect to a current

transformer.

Current transformers specifications: The accuracy class is 0.5, and the current on the secondary

side is 1 A or 5 A.

•Three-phase four-wire

connection

•Three-phase three-wire connection

(1) Shield layer of the signal cable

SmartLogger networking

In the SmartLogger

networking scenario, the

power meter is connected to

the SmartLogger. In the non-

SmartLogger networking

scenario, the power meter is

connected to the inverter.

Please ensure that the

ground cable is installed

securely. Poor grounding

may cause electric shocks.

•You need to set

parameters after cable

connections are

complete. For details, see

section 4 "Display and

Parameter Settings".

•For the three-phase

three-wire connection,

phase B does not need to

connect to a current

transformer.

•Three-phase four-wire connection

•Three-phase three-wire connection

(1) Shield layer of the signal cable

Smart Dongle networking

3.4 Connection Through Current Transformer and Potential

Transformer (Current ≥ 0 A, Line Voltage > 500 V)

3.5

Please ensure that the

ground cable is installed

securely. Poor grounding

may cause electric shocks.

Cable outlet (OUT)

•Three-phase four-wire connection

Cable outlet (OUT)

Current

transformers

Cable inlet (IN)

UA UB UC UN

Cable inlet (IN)

UA UB UC

You need to set parameters

after cable connections are

complete. For details, see

section 4 "Display and

Parameter Settings".

Current

transformers

•Three-phase three-wire connection

Indice

Altri manuali Huawei Accessori

Huawei

Huawei NetCol5000-C Manuale utente

Huawei

Huawei DDSU666-H Manuale utente

Huawei

Huawei iSiteC BTS3601C Manuale utente

Huawei

Huawei Airbridge DBS3900 Specifiche tecniche

Huawei

Huawei BTS3900A Istruzioni operative originali

Huawei

Huawei BBU3900 Manuale del proprietario

Huawei

Huawei RRU3268 Manuale utente

Huawei

Huawei BTS3701B Manuale utente

Huawei

Huawei NetCol5000-A Manuale utente

Huawei

Huawei NetCol8000-A013 Manuale utente

Huawei

Huawei 3900 Series Guida rapida

Huawei

Huawei BTS3606 Manuale utente

Huawei

Huawei FusionCol8000-E260 Manuale utente

Huawei

Huawei FusionCol8000-E260 Manuale utente

Huawei

Huawei RRU3942 Guida

Huawei

Huawei Airbridge cBTS3612-1900 Manuale utente

Huawei

Huawei eNodeB Manuale utente

Huawei

Huawei FusionCol8000-E240 Manuale utente

Huawei

Huawei NetCol5000-A021HN12D 20020E1 Manuale utente

Huawei

Huawei Airbridge cBTS3612 Manuale utente

Huawei

Huawei BTS3902E WCDMA Manuale utente

Huawei

Huawei RRU3201 Manuale utente

Huawei

Huawei RRU3642 Manuale utente

Huawei

Huawei NetCol5000-A025 Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente