Huawei SmartACU2000D Series Manuale utente

HUAWEI TECHNOLOGIES CO., LTD.

SmartACU2000D Smart Array Controller

Quick Guide (with No PID Module)

Issue: 02

Part Number: 31500BWD

Date: 2020-04-10

1Product Overview

1. The information in this document is subject to change due to version upgrade or other reasons.

Every effort has been made in the preparation of this document to ensure accuracy of the

contents, but all statements, information, and recommendations in this document do not

constitute a warranty of any kind, express or implied.

2. Before installing the device, closely read the SmartACU2000D Smart Array Controller User

Manual (with no PID module) to get familiar with product information and precautions.

3. Only qualified and trained electrical technicians are allowed to operate the device. Operation

personnel should understand the composition and working principles of the grid-tied PV power

system and local regulations.

4. Before installing the device, check that the package contents are intact and complete against the

packing list. If any damage is found or any component is missing, contact your dealer.

5. Use insulated tools when installing the device. For personal safety, wear insulation gloves and

protective shoes.

6. When installing the device and connecting cables, use appropriate tools and take necessary

protective measures to avoid damaging the device.

7. Huawei shall not be liable for any consequence caused by violation of the storage, installation,

and operation regulations specified in this document and the user manual.

Name

Model

Voltage Level

Configuration

Smart array

controller

SmartACU2000D

-D-00

D: ≤ 800 V

three

-phase

AC input

•

00: one MBUS route

•

02: two MBUS routes

•

05CN: one MBUS route and 4G

antenna

SmartACU2000D

-D-02

SmartACU2000D

-D-05CN

Cabinet Dimensions

(1) Cabinet door

(2) Mounting plate

(3) Waterproof connector for the protective earthing

cable (PE, 3/4 in.)

(4) Waterproof connectors for the RS485

communications cable, network cable, and

DC power cables (RS485/ETH/DC, 3/4 in.)

(5) Waterproof connector for the

DO signal cable

(DO, 5/4 in.)

(6) Waterproof connector for the DI signal cable

(DI, 3/4 in.)

(7) Waterproof connector for the AI signal cable (AI,

5/4 in.)

(8) USB port (USB)

(9) Waterproof connectors for the RS485

communications cable and network cable

(RS485/ETH, 3/4 in.)

(10) Ventilation valve

(11) Waterproof connectors for the three

phase AC

power cable (MBUS01, MBUS02, 1 in.)

(12) Waterproof connector for the single

-phase

AC power cable (AC INPUT, 3/4 in.)

(13) Waterproof connector for the optical cable

(SFP1, 3/4 in.)

(14) Waterproof connector for the optical cable,

network cable, or 4G antenna (SFP2/4G

LTE/4G, 3/4 in.)

SmartACU2000D-D-02 Components

For simplicity purposes, the following figure shows only the components that you need to operate and

reserved installation positions.

(1)

SmartLogger power adapter (U01)

(11) Position for the power over Ethernet (PoE)

SPD

(2) Position for the 24 V DC power module (U02)

(12) Position for the

PoE module (POE)

(3) AC input terminal of the 24 V power module

(JX02)

(13)

ATB (Access Terminal Box)

(4) Single

-phase surge protective device (SPD)

(F03)

(14) Single

-phase input switch (QF03)

(5) Three

-phase SPD 1 (F01)

(15) Three

-phase input switch 2 (FU02)

(6) Three

-phase SPD 2 (F02)

(16) Three

-phase input switch 1 (FU01)

(7) Position for the Ethernet switch (SWITCH)

(17

) RS485 communications terminal (JX01)

(8) SmartMBUS CCO (MBUS CCO)

(18) Position for the SmartModule1000A01

(SmartModule)

(9) SmartLogger3000

(SmartLogger)

(19) PE bar

(10) Optical fiber adapter (OFA01, OFA02)

SmartACU2000D-D-00 and SmartACU2000D-D-05CN Components

(1)

SmartLogger power adapter (U01)

(10)

Position for the PoE SPD

(2) Position for the 24 V DC power module (U02)

(11)

Position for the PoE module (POE)

(3) AC input terminal of the 24 V power module

(JX02)

(12) ATB (

Access Terminal Box)

(4) Single

-phase SPD (F03)

(13)

Single-phase input switch (QF03)

(5) Three

-phase SPD (F01)

(14)

Three-phase input switch (FU01)

(6)

Position for the Ethernet switch (SWITCH)

(15)

RS485 communications terminal (JX01)

(7)

Position for the SmartMBUS CCO (MBUS

CCO)

(16)

Position for the SmartModule1000A01

(SmartModule)

(8)

SmartLogger3000 (SmartLogger)

(17)

PE bar

(9)

Optical fiber adapter (OFA01, OFA02)

For simplicity purposes, the following figure shows only the components that you need to operate

and reserved installation positions.

2Configurations in Typical Scenarios

Components in dashed-line boxes are optional. To highlight the involved area, the figure does not

show all factory-installed components and cables.

Fiber Ring Network

Only the SmartACU2000D-D-00 and SmartACU2000D-D-02 are applicable to this scenario.

Position

Component

Recommended Model or

Specifications

Component

Source

Quantity

Smart array

controller

(Optional) SmartModule

SmartModule1000A01

Purchased

from Huawei

(Optional) Ethernet

switch

-H605 or ES1000

(Optional) 24 V power

supply

N/A

Fitting bag

for optical

ring

switching

Optical

module

N/A

Optical

jumper

N/A

Transformer

station

Miniature circuit breaker

(MCB)

Recommended rated

current: 32 A; number of

poles: 2

Prepared by

the customer

Three

phase

power switch

Knife fuse

switch

•

When the rated AC

voltage on the low-

voltage (LV) side of the

transformer station is

less than or equal to

600 V, the rated

voltage of the knife

fuse switch should be

greater than or equal to

600 V.

•

When the rated AC

voltage on the LV side

of the transformer

station is greater than

600 V and less than or

equal to 800 V, the

rated voltage of the

knife fuse switch

should be greater than

or equal to 800 V.

•

Recommended rated

current of the fuse: 32

A; rated current of the

knife fuse switch box: ≥

32 A; number of poles:

3 (three fuses for each

knife fuse switch box)

•Scenario with a

double-column

transformer: 1

•Scenario with a

dual-split

transformer: 2

Note a: There are two types of fitting bags for fiber ring switching: with 100M optical modules or with

1000M optical modules. You can purchase a fitting bag based on the specifications of the optical

modules used on the fiber channel (FC) switch.

The following table describes the components to be configured in the fiber ring network scenario.

•Components listed in the table need to be installed onsite.

•Models of the components inside the transformer station are specified by the transformer station

vendor.

No.

Cable

Recommended Model or Specifications

Cross

-sectional Area

Range of the Cable

(Recommended Value)

Three

-phase AC

power cable

•

Three-core (L1, L2, and L3) outdoor

armored copper cable

•When the rated AC voltage on the LV side

of the transformer station is less than or

equal to 600 V, the operating voltage

between the three-

phase AC power cable

and the ground should be greater than or

equal to 600 V.

•When the rated AC voltage on the LV side

of the transformer station is greater than

600 V and less than or equal to 800 V, the

operating voltage between the three-

phase AC power cable and the ground

should be greater than or equal to 1000 V.

•

8–10 mm2(10 mm2)

•

8 AWG

(Optional)

Peripheral network

cable

CAT 5E outdoor shielded network cable with

an outer diameter less than 9 mm (0.35 in.)

and internal resistance less than or equal to

1.5 ohms/10 m (1.5 ohms/393.70 in.), as well

as shielded RJ45 connectors

N/A

Peripheral RS485

communications

cable

Computer cable (DJYP2VP2

-22 2x2x1) or

armored shielded twisted pair that can be

used outdoors, as well as OT

-M4 terminals

•

0.5–1 mm2(1 mm2)

•

20–

18 AWG (18 AWG)

Cabinet PE cable

Outdoor copper cable and OT

-M6 terminals

•

6–16 mm2(16 mm2)

•

10–6 AWG (6 AWG)

Optical fiber cable

Four

-core or eight-core single-

mode armored

optical cable with a transmission wavelength

of 1310 nm and an outer diameter less than

or equal to 18 mm (0.71 in.)

N/A

Single

-phase AC

power cable

•

Standard connection: two-core outdoor

armored copper cable

•

Connection through a tube: single-core

outdoor copper cable

•

Operating voltage to the ground ≥ 300 V

•

4–6 mm2(4 mm2)

•

12–

10 AWG (12 AWG)

(Optional) 24 V DC

output power cable

•

Standard connection: two-core outdoor

armored copper cable

•

Connection through a tube: single-core

outdoor copper cable

•

Operating voltage to the ground ≥ 300 V

•

2.5–4 mm2(2.5 mm2)

•

14–

12 AWG (14 AWG)

The following table describes the cables to be prepared by yourself in the fiber ring network scenario.

Components in dashed-line boxes are optional. To highlight the involved area, the figure does not

show all factory-installed components and cables.

4G LTE Network

Only the SmartACU2000D-D-00 and SmartACU2000D-D-02 are applicable to this scenario.

Position

Component

Recommended Model

or Specifications

Component

Source

Quantity

Smart array

controller

(Optional) SmartModule

SmartModule1000A01

Purchased

from Huawei

(Optional) 24 V power

supply

N/A

Fitting bags

for the PoE

module and

customer

premises

equipment

(CPE)

PoE

module

N/A

Outside the

smart array

controller and

transformer

station

CPE

N/A

Transformer

station

Miniature circuit breaker

(MCB)

Rated current: 32 A,

number of poles: 2

Prepared by

the customer

Three

phase

power switch

Knife

fuse

switch

•

When the rated AC

voltage on the LV

side

of the transformer

station is less than or

equal to 600 V, the

rated voltage of the

knife fuse switch

should be greater

than or equal to 600

•

When the rated AC

voltage on the LV side

of the transformer

station is greater than

600 V and less than

or equal to 800 V, the

rated voltage of the

knife fuse switch

should be greater

than or equal to 800

•Recommended rated

current of the fuse: 32

A; rated current of the

knife fuse switch box:

≥ 32 A; number of

poles: 3 (three fuses

for each knife fuse

switch box)

•Scenario with a

double-

column

transformer: 1

•Scenario with a

dual-split

transformer: 2

The following table describes the components to be configured in the 4G LTE network scenario.

•Components listed in the table need to be installed onsite.

•Models of the components inside the transformer station are specified by the transformer station

vendor.

Altri manuali per SmartACU2000D Series

Indice

Altri manuali Huawei Controllori

Huawei

Huawei ECC800 Manuale utente

Huawei

Huawei SmartACU2000D Series Manuale utente

Huawei

Huawei ECC800 Manuale utente

Huawei

Huawei SmartACU2000D Series Manuale utente

Huawei

Huawei ECC800 Manuale utente

Huawei

Huawei SUN2000-20KTL-M3 Manuale utente

Huawei

Huawei AC & Fit AP Manuale operativo

Huawei

Huawei ECC800 Manuale utente

Huawei

Huawei NetCol5000-A Manuale utente

Huawei

Huawei SmartACU2000B Manuale utente

Huawei

Huawei PDU8000-0125DCV8-BXA006 Manuale utente

Huawei

Huawei SmartACU2000B Manuale utente

Huawei

Huawei ECC500 Manuale utente

Huawei

Huawei ECC500 Manuale utente

Huawei

Huawei ECC800 Manuale utente

Huawei

Huawei V100R021C10 Manuale utente

Huawei

Huawei SmartACU2000D Series Manuale utente

Huawei

Huawei SmartACU2000B Manuale utente

Huawei

Huawei V100R001C50 Manuale utente

Huawei

Huawei SUN2000-3KTL-M1 Manuale utente

Huawei

Huawei Backup Box-B0 Manuale utente

Huawei

Huawei APAA00001 Manuale utente

Huawei

Huawei SE2900 Guida

Huawei

Huawei ECC800-Pro Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente