Huawei ATN 910C-K Manuale utente

(IEC 19-inch & ETSI 21-inch Cabinet)

1 U Quick Installation Guide

This document applies to the installation of the ATN 910C-K/M/G,

ATN 910D-A, NetEngine 8000 M1A/M1C, and OptiX PTN 916-F.

Issue：01

Device Overview

DC chassis

AC chassis

DC and AC Chassis are installed in the same way. For installation

details, see the corresponding installation guide.

Figures in the document are for reference only and may be dierent

from actual devices.

The type and quantity of items in an installation accessory package

vary according to the device model. Check the delivered items

against the actual packing list.

NOTE

DC and AC power modules can be installed in any of the power module

slots on the ATN 910C-K/M and ATN 910D-A.

NOTE

Packing list

Insulation tape Serial cable

Label cable tie

Fiber binding tape

Panel screw (M6x12)Floating nut (M6)

Signal cable label

Cable tie (300 x 3.6 mm)

Power cable label

Cable management frame

Corrugated pipe ESD wrist strap

Device Overview

Technical Speciﬁcations

Item

Chassis height

[U]

Maximum input

current [A]

Input voltage

range [V]

Maximum input

current [A]

DC Chassis

1 U

44.45 mm x 442 mm x 220

mm(1.75 in. x 17.4 in. x 8.66

in.)

OptiX PTN 916-F: 4.0 kg

NetEngine 8000 M1A: 3.9 kg

NetEngine 8000 M1C：3.8 kg

ATN 910C-K: 4.0 kg

ATN 910C-M: 3.8 kg

ATN 910C-G: 3.9 kg

ATN 910D-A: 4.2 kg

OptiX PTN 916-F: 2.5 A

NetEngine 8000 M1A: 4 A

NetEngine 8000 M1C: 10 A

ATN 910C-K/M: 10 A

ATN 910C-G: 4 A

ATN 910D-A: 10 A

-48 V/-60 V

-40 V to -72 V 100 V to 240 V

OptiX PTN 916-F/NetEngine

8000 M1A/ATN 910C-G:

110 V/220 V

NetEngine 8000 M1C/ATN

910C-K/M/ATN 910D-A: 200 V

to 240 V/100 V to 127 V dual

live wires, support 240V HVDC

AC Chassis

1 U

44.45 mm x 442 mm x 220

mm(1.75 in. x 17.4 in. x 8.66

in.)

OptiX PTN 916-F: 3.6 kg

NetEngine 8000 M1A: 4.5 kg

NetEngine 8000 M1C：3.9 kg

ATN 910C-K: 4.1 kg

ATN 910C-M: 3.9 kg

ATN 910C-G: 4.5 kg

ATN 910D-A: 4.3 kg

OptiX PTN 916-F: 1.5 A

NetEngine 8000 M1A: 1.5 A

NetEngine 8000 M1C: 4 A

ATN 910C-K/M: 4 A

ATN 910C-G: 1.5 A

ATN 910D-A: 4 A

Dimensions

without

packaging (H

x W x D)

[mm(in.)]

Weight without

packaging (base

conﬁguration)

[kg(lb)]

Safety Guidelines

Observe all safety regulations and precautions

Only trained and qualiﬁed personnel are allowed to install, operate

or maintain the equipment. Familiarize yourself with all safety pre-

cautions before performing any operation on the equipment.

Operator qualiﬁcations

To ensure personal and equipment safety, observe all the safety

precautions on the equipmentand in this document.

and and items do not cover all the safety precautions and

are only supplementary to the safety precautions.

Follow all the safety precautions and instructions provided by Huawei.

The safety precautions outlined in this document are only requirements

of Huawei and do not cover general safety regulations. Huawei is not

liable for any consequence that results from violation of regulation

spertaining to safe operations or safety codes pertaining to design,

production, and equipment use.

DANGER WARNING

CAUTION NOTICE

Do not install or remove the equipment or power cables while power is on.

To ensure equipment and personal safety, ground the equipment before

powering it on.

DANGER

Use multiple persons to move or lift a chassis and take measures to

protect personal safety.

Laser beams will cause eye damage. Do not look into bores of optical

modules or opticalﬁbers without eye protection.

WARNING

During equipment transport and installation, prevent the equipment

from colliding with objects like doors, walls, or shelves.

Move an unpacked chassis upright. Do not drag it with it lying down.

Do not touch unpainted surfaces of the equipment with wet or

contaminated gloves.

Do not open the ESD bags of cards and modules until they are delivered

to the equipmentroom. When taking a card out of the ESD bag, do not

use the connector to support the card's weight because this operation

will distort the connector and make the pins on the backplane connector

bend.

NOTICE

Before installing, operating, or maintaining the

equipment, wear an ESD wrist strap and insert the other

end into the ESD jack on the chassis or cabinet. Remove

conductive objects like jewelry and watches to prevent

damages to the equipment and cards caused by

electrostatic discharge.

ESD Protection

Site Requirements

To ensure personal and equipment safety, observe all the safety

precautions on the equipmentand in this document.

and and items do not cover all the safety precautions and

are only supplementary to the safety precautions. The device needs to be installed in a clean, dry, well ventilated, and

temperature-controllable standard equipment room.In addition, the

equipment room must be free from leaking or dripping water, heavy

dew, and condensing.

Dustproof measures must be taken in the installation site. This is

because dust will cause electrostatic discharges on the device and aect

connections of metal connectors and joints, shortening the service life

of the device and even resulting in device failures.

The installation site must be free from acidic, alkaline, and other types

of corrosive gases.

The device that is operating may cause radio interference. If this is the

case, relevant measures may be needed to reduce the interference.

Generally, devices such as wireless antennas should not be installed in

the equipment room. If such devices must be installed indoors, ensure

that the electromagnetic environment meets relevant requirements or

take necessary electromagnetic shielding measures.

The device to be installed must be used indoors. To ensure normal

operation and long service life of the device, the following requirements

must be met:

The temperature and humidity in the installation site must meet device

requirements described in the following table.

Long-term operating

temperature [°C]

Relative operating

humidity [RH]

–40°C to +65°C

≤ 4000 m (For the altitude in the range of 1800 m to

4000 m, the operating temperature ofthe device

decreases by 1°C every time the altitude increases

by 220 m.)

Item Requirements

Storage temperature

[°C] –40°C to +70°C

Relative storage

humidity [RH]

Long-term operating

altitude [m]

Storage altitude [m] < 5000 m

OptiX PTN 916-F: Long-term: 10% to 90% RH,

non-condensing Short-term: N/A

Other devices: Long-term: 5% to 85% RH,

non-condensing Short-term: N/A

OptiX PTN 916-F: 10% to 100% RH, non-condensing

Other devices: 5% to 100% RH, non-condensing

Cabinet Requirements

NOTE

The device must be installed in an IEC 19-inch cabinet or an ETSI 21-inch

cabinet.

Huawei A63E cabinet is recommended. If customers choose to purchase

cabinets by themselves, the cabinets must meet the following

requirements:

1. 19-inch or 21-inch cabinet with a depth of greater than or equal to

300 mm.

2. The cabling space in front of the cabinet complies with the cabling

space requirements of boards. It is recommended that the distance

between the cabinet door and any device board be greater than or equal

to 120 mm. If the cabling space is insucient, cables will block the

cabinet door from closing. Therefore, a cabinet with broader cabling

space is recommended, such as a cabinet with a convex door.

3. The device draws air from the left side and exhausts from the right

side. Therefore, if the device is installed in a 19-inch cabinet, there must

be a clearance of at least 75 mm at the left and right sides of the

cabinet to ensure good ventilation.

4. The porosity of each cabinet door must be greater than 50%, meeting

heat dissipation requirements of devices.

5. The cabinet has installation accessories, such as guide rails, ﬂoating

nuts, and screws.

6. The cabinet has a ground terminal to connect to the device.

7. The cabinet has a cable outlet on the top or at the bottom for

overhead or underﬂoor cabling.

The cabinet may be installed on an ESD ﬂoor or a concrete ﬂoor. For

details about how to install a cabinet, see the Cabinet Installation

Guide delivered with a cabinet.

For cabinets with left-to-right air channels, such as open racks,

installing cabinets side by side may cause cascaded heating. Therefore,

you are advised to install cabinets with left-to-right air channels verti-

cally at dierent levels rather than side by side. If side-by-side installa-

tion cannot be avoided, it is recommended that the distance between

cabinets be at least 500 mm (19.67 in.).

If the device requires optical modules or attenuators with a puller,

ensure that sucient space is available for routing optical ﬁbers. For a

convex door or open rack, it is recommended that the distance

between the cabinet door and the front panel of the board be greater

than or equal to 120 mm (4.72 in.).

Installing a Device

5.1 Installing a Device in an IEC 19-Inch Cabinet

1Install ﬂoating nuts onto the cabinet.

When installing a device in a cabinet, ensure that the total heat

consumption of all devices in the cabinet does not exceed the heat

dissipation capability of the cabinet.

To prevent air return from aecting heat dissipation, leave at least 2 U

space between devices in the cabinet.

Do not block the heat dissipation holes on panels.

A device that needs to share the same cabinet with other devices

cannot be installed near the air exhaust vents of those devices.

Consider the impact of a device's air exhaust vent on adjacent devices

to prevent high temperature.

When fastening ﬂoating nuts, ensure that there is at least 75 mm

space on the left and right sides of the device for ventilation after

device installation.

CAUTION

Installation hole

Floating nut

NOTE

Certain steps support two installation modes. Select a proper PGND

cable installation mode according to cabling requirements. The PGND

cable can be connected to either the front or side face of the device.

Connecting the cable to the side face is preferred.

Figures in the document are for reference only, and the actual device

appearance may vary depending on the exact device model.

Installing a Device

PWR2 PWR1

2Connect the PGND cable to the front or side face of the device.

Connecting the cable to the side face is preferred.

Installing a Device

3Install the device into the cabinet.

ATN 910D-A

CLK/TOD

ETH/OAM

ALM/ALMO

RST

STAT

CLK/TEST

ALM

012345678910 11 12 13 14 15 16 17 18 19 20 21 22 23

10GE/FE/(0~7) 25GE/10GE/GE(8~23) BREAKOUT 012324 25

100GE/50GE

26 27

PWR2 PWR1

Installing a Device

5.2 Installing a Device in an ETSI 21-Inch Cabinet

with Front Columns

1Install ﬂoating nuts onto the cabinet.

2Install the conversion mounting ears on both sides of the chassis.

Installation hole

Floating nut

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Huawei Router di rete

Huawei

Huawei AR150 series Manuale utente

Huawei

Huawei B683 Manuale utente

Huawei

Huawei S Series Guida di riferimento rapido

Huawei

Huawei B683-74V Manuale utente

Huawei

Huawei AR Series Manuale utente

Huawei

Huawei WA1003A-RU Manuale utente

Huawei

Huawei E5170s-22 Manuale utente

Huawei

Huawei AR1200 Series Manuale utente

Huawei

Huawei E5 Manuale utente

Huawei

Huawei Pocket WiFi 4G Manuale di installazione e funzionamento

Huawei

Huawei AR1200 Series Manuale di istruzioni

Huawei

Huawei WiFi Mesh 3 Manuale utente

Huawei

Huawei AR3200 Series Manuale utente

Huawei

Huawei B311-520 Manuale utente

Huawei

Huawei B311s-220 Manuale utente

Huawei

Huawei Quidway NetEngine 20 series Manuale utente

Huawei

Huawei AR550 Series Manuale utente

Huawei

Huawei WiFi AX3 Manuale utente

Huawei

Huawei B2368 Manuale utente

Huawei

Huawei AR150 series Manuale utente

Huawei

Huawei AR1200 Series Manuale utente

Huawei

Huawei Quidway S9300 Manuale utente

Huawei

Huawei UR-LPUF Manuale

Huawei

Huawei HG232f Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza