Huawei S1700 Series Manuale utente

1U=44.45mm

Fix the captive nuts.

安装浮动螺母。

Use installation strip tofix the captive nuts.

使用安装条安装浮动螺母。

● Leave more than 1U space between the devices for proper heat dissipation.

● 设备与设备之间的距离必须大于1U。

技术支持

Service and Support

Tool List

工具参考

斜口钳

Diagonal pliers

Crosshead screwdriver

十字螺丝刀

Flathead screwdriver

一字螺丝刀

光纤绑扎带

Optical fiber bundling tape

线扣

Cable tie

防静电手套

ESD-preventive

Percussion drill(φ8 Drill bit)

冲击钻（φ8钻头）

M6 Plug bolt

M6膨胀螺栓

活动扳手

Adjustable spanner

羊角锤

Claw hammer

Marker pen

记号笔

Rev: 03 The device model is on the product nameplate. 设备的具体型号信息请从产品铭牌上获取。

快速安装指南以及简易使用说明书

S1700 Series Ethernet Switches

User Manual & Installation Quick Start

S1700 Managed Series Ethernet Switches include S1700-28GFR-4P-AC、S1700-52GFR-4P-AC、S1700-28FR-2T2P-AC、S1700-52FR-2T2P-AC.

S1700网管型以太网交换机系列包含S1700-28GFR-4P-AC、S1700-52GFR-4P-AC、S1700-28FR-2T2P-AC、S1700-52FR-2T2P-AC。

短挂耳

Short rack-mounting ear

胶垫贴

Rubber pads

浮动螺母

Captive nut

M6螺钉

M6 screw

M4螺钉

M4 screw

Installing the Device in a 19'' Cabinet

安装设备到19英寸标准机柜/机架中

Accessories

安装附件介绍

Precautions

注意事项

S1700系列以太网交换机

Before installation, take ESD-preventive measures, for example, wear ESD-preventive gloves or a wrist strap.

安装前请做好防静电保护措施，如配戴防静电手套或防静电手腕。

Fix the rack-mounting ears.

安装挂耳。

IEC cabinet (19 inch)

IEC 机柜(19英寸)

Install the device in a cabinet.

安装设备到机柜。

Installing the Device on a Worktable

安装设备到工作台

安装设备到墙面

Installing the Device on a Wall

Adhibit the rubber pads.

粘贴胶垫贴。

Install the device on a worktable.

安装设备到工作台。

Rubber pads

胶垫贴

Install the device on the wall.

安装设备到墙面。

Fix the rack-mounting ears.

安装挂耳。

Mark the hole locations on the wall according to

the device installed with rack-mounting ears.

根据已安装挂耳的设备，用记号笔标记打孔位置。

φ8 Drill bit

φ8钻头

M6 plug bolt

M6膨胀螺栓

90。

Install the plug bolt.

安装膨胀螺栓。

●To prevent injuries, check that there is no electrical wire at the locations to be drilled before drilling holes in the wall.

●

Flammable and explosive items under the device is prohibited. Leave more than 100 mm of space around the device for proper heat dissipation.

在墙上打孔时，必须确认打孔处没有墙电，避免造成人身伤害。

设备下方禁止摆放易燃易爆物品，距离设备100mm范围内不能有异物挡住。

● Do not connect power cables when the device is powered on, so as to avoid injuries.

● Please use the metal-covered optical module.

● Please use SFP transceiver to meet laser class 1 standard.

● 请使用SFP transceiver 满足 Laser Class 1。

● 请使用有金属外壳的光模块。

● Do not power on the device before device installation and cabling are completed.

● Make sure that the protection grounding cable of the device is grounded.

● The device can use only AC power supply.

● 严禁带电安装电源线，以免造成人身伤害。

● 严禁在设备安装和布线完成前向设备供电。

● 确定设备保护地线接地。

● 设备支持交流电源。

Connecting PGND Cables and Power Cables

连接保护地线和电源线

Connect the AC power cable.

连接交流电源线。

Connect the PGND cable.

连接地线。

Installing the SFP Transceiver

SFP收发器的安装

Insert the transceiver with the optical connector

facing outward and the slot connector facing down.

插入SFP收发器，光纤连接口朝外，且插槽朝下。

Connect the LC connector to SFP transceiver.

将光纤的LC连接器连接到光模块上。

线扣

Cable tie

Optical fibers

光纤

Fiber bundling tape

光纤绑扎带

Laying out Cables

布放线缆

● Do not stare at optical interfaces. The optical fiber contains laser light sources that hurt human eyes.

● Lay out and bundle power cables, optical fibers, and Ethernet cables separately, with the distances in between longer than 10 cm.

● 不要直视光纤接口，光纤中的激光会伤害眼睛。

● 电源线与信号线缆的间距要大于10厘米。

During the cabling, if the quantity of cables is rather great, you can route the cables in the cabinet first, and then install connectors

to the cables.

布线时，如果线缆数目比较多，为了布线更方便，可以先不做线缆接头，先将线缆在机柜中布置好，再做与设备连接的线缆接头。

connectors

1-24 Port LED

1-24 端口指示灯

GE1-GE4 Port LED

GE1-GE4 端口指示灯

*此为A级产品，在生活环境中，该产品可能会造成无线电干扰，在这种情况下，可能需要用户对其干扰采取切实可行的防护措施。

This is a Class A product. This product may cause radio interference, in which case the user may be required to take practical precautions interference.

LED Indicator

LED状态

LED Condition

状态

Description

描述

1 - 24 Port

GE3 - GE4 Port On Green

绿色常亮

Blinking indicates activity for 1000Mbps.

Blinking indicates activity for 10/100Mbps.

表示正在1000Mbps模式下传输数据。

表示正在10/100Mbps模式下传输数据。

The port has a valid 1000Mbps link.

端口工作在1000Mbps模式下。

端口工作在10/100Mbps模式下。

The port has a valid 10/100Mbps link.

Blinking Green

绿色闪烁

Off

熄灭

No link.

Off No link.

无效连接。

熄灭

On Green

绿色常亮

Blinking Green

绿色闪烁

Off

熄灭

On Green

绿色常亮

Blinking Green

绿色闪烁

Off

熄灭

无效连接。

GE1 - GE2 Port On Green

绿色常亮

On Amber

橙色常亮

Blinking Green

绿色闪烁

Blinking indicates activity.

表示正在传输数据。

The port has a valid 10/100Mbps link.

端口工作在10/100Mbps模式下。

No link.

无效连接。

Blinking indicates activity.

闪烁表示正在传输数据。

Blinking Amber

橙色闪烁

PWR

RUN

On Green

绿色常亮

Internal power is operating normally.

System boots up or works abnormal.

设备正常上电。

Off

熄灭

Power off.

设备未上电

系统正在启动或工作异常。

System works normally.

系统工作正常。

System off.

系统未启动。

。

S1700-28FR-2T2P-AC对应图

1-24 Port LED

1-24 端口指示灯

25-28 Port LED

25-28 端口指示灯

*此为A级产品，在生活环境中，该产品可能会造成无线电干扰，在这种情况下，可能需要用户对其干扰采取切实可行的防护措施。

This is a Class A product. This product may cause radio interference, in which case the user may be required to take practical precautions interference.

LED Indicator

LED状态

LED Condition

状态

Description

描述

1 - 24 Port

25 - 28 Port The port has a valid 1000Mbps link.

端口工作在1000Mbps模式下。

Off

熄灭

No link.

无效连接。

On Green

绿色常亮

Blinking Green

绿色闪烁

Off

熄灭

On Green

绿色常亮

Blinking Green

绿色闪烁

On Green

绿色常亮

10/1 模式下。端口工作在 00Mbps

The port has a valid 10/100Mbps link.

On Amber

橙色常亮

Blinking Green

绿色闪烁

The port has a valid 1000Mbps link.

端口工作在1000Mbps模式下。

Off

熄灭

No link.

无效连接。

Blinking indicates activity.

闪烁表示正在传输数据。

Blinking indicates activity for 10/100Mbps.

表示正在10/100Mbps模式下传输数据。

Blinking indicates activity for 1000Mbps.

表示正在1000Mbps模式下传输数据。

Blinking Amber

橙色闪烁

PWR

RUN

On Green

绿色常亮

Internal power is operating normally.

System boots up or works abnormal.

设备正常上电。

Off

熄灭

Power off.

设备未上电

系统正在启动或工作异常。

System works normally.

系统工作正常。

System off.

系统未启动。

。

S1700-28GFR-4P-AC对应图

1-48 Port LED

1-48 端口指示灯

GE1-GE4 Port LED

GE1-GE4 端口指示灯

*此为A级产品，在生活环境中，该产品可能会造成无线电干扰，在这种情况下，可能需要用户对其干扰采取切实可行的防护措施。

This is a Class A product. This product may cause radio interference, in which case the user may be required to take practical precautions interference.

LED Indicator

LED状态

LED Condition

状态

Description

描述

1 - 48 Port

GE3 - GE4 Port On Green

绿色常亮

Blinking indicates activity for 1000Mbps.

Blinking indicates activity for 10/100Mbps.

表示正在1000Mbps模式下传输数据。

表示正在10/100Mbps模式下传输数据。

The port has a valid 1000Mbps link.

端口工作在1000Mbps模式下。

端口工作在10/100Mbps模式下。

The port has a valid 10/100Mbps link.

Blinking Green

绿色闪烁

Off

熄灭

No link.

Off No link.

无效连接。

熄灭

On Green

绿色常亮

Blinking Green

绿色闪烁

Off

熄灭

On Green

绿色常亮

Blinking Green

绿色闪烁

Off

熄灭

无效连接。

GE1 - GE2 Port On Green

绿色常亮

On Amber

橙色常亮

Blinking Green

绿色闪烁

Blinking indicates activity.

表示正在传输数据。

The port has a valid 10/100Mbps link.

端口工作在10/100Mbps模式下。

No link.

无效连接。

Blinking indicates activity.

闪烁表示正在传输数据。

Blinking Amber

橙色闪烁

PWR

RUN

On Green

绿色常亮

Internal power is operating normally.

System boots up or works abnormal.

设备正常上电。

Off

熄灭

Power off.

设备未上电

系统正在启动或工作异常。

System works normally.

系统工作正常。

System off.

系统未启动。

。

S1700-52FR-2T2P-AC对应图

1-48 Port LED

1-48 端口指示灯

49-52 Port LED

49-52 端口指示灯

*此为A级产品，在生活环境中，该产品可能会造成无线电干扰，在这种情况下，可能需要用户对其干扰采取切实可行的防护措施。

This is a Class A product. This product may cause radio interference, in which case the user may be required to take practical precautions interference.

S1700-52GFR-4P-AC对应图

LED Indicator

LED状态

LED Condition

状态

Description

描述

1 - 48 Port

49 - 52 Port The port has a valid 1000Mbps link.

端口工作在1000Mbps模式下。

Off

熄灭

No link.

无效连接。

On Green

绿色常亮

Blinking Green

绿色闪烁

Off

熄灭

On Green

绿色常亮

Blinking Green

绿色闪烁

On Green

绿色常亮

10/1 模式下。端口工作在 00Mbps

The port has a valid 10/100Mbps link.

On Amber

橙色常亮

Blinking Green

绿色闪烁

The port has a valid 1000Mbps link.

端口工作在1000Mbps模式下。

Off

熄灭

No link.

无效连接。

Blinking indicates activity.

闪烁表示正在传输数据。

Blinking indicates activity for 10/100Mbps.

表示正在10/100Mbps模式下传输数据。

Blinking indicates activity for 1000Mbps.

表示正在1000Mbps模式下传输数据。

Blinking Amber

橙色闪烁

PWR

RUN

On Green

绿色常亮

Internal power is operating normally.

System boots up or works abnormal.

设备正常上电。

Off

熄灭

Power off.

设备未上电

系统正在启动或工作异常。

System works normally.

系统工作正常。

System off.

系统未启动。

。

Altri manuali per S1700 Series

Indice

Altri manuali Huawei Router di rete

Huawei

Huawei UR-LPUF Manuale

Huawei

Huawei B2368 Manuale utente

Huawei

Huawei AR150 series Manuale utente

Huawei

Huawei WS880 Manuale utente

Huawei

Huawei WiFi Mesh 3 Specifiche tecniche

Huawei

Huawei OptiXstar HG8145X6-10 Manuale utente

Huawei

Huawei H112 Manuale utente

Huawei

Huawei B618 Manuale utente

Huawei

Huawei B320-323 Manuale utente

Huawei

Huawei WiFi Q2 Pro Manuale utente

Huawei

Huawei EG8143A5 Manuale utente

Huawei

Huawei B310 Manuale utente

Huawei

Huawei V200R001 Manuale utente

Huawei

Huawei AR2200 Series Manuale utente

Huawei

Huawei CX210 Guida di riferimento rapido

Huawei

Huawei E5 Manuale utente

Huawei

Huawei 31010GAS Manuale utente

Huawei

Huawei 31010GEV Manuale utente

Huawei

Huawei Quidway S9300 Manuale utente

Huawei

Huawei Pocket WiFi 3G Manuale di installazione e funzionamento

Huawei

Huawei B311 Manuale utente

Huawei

Huawei B311-221 Manuale utente

Huawei

Huawei Mobile wifi e5330 Manuale utente

Huawei

Huawei H122-372 Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza