Huawei FusionModule500 Manuale utente

FusionModule500 Smart Mini Data Center

Quick Guide (02116410,

02116411, 02116412)

Huawei Technologies Co., Ltd.

Issue: 01

Date: 2021-07-15

Item Specifications

Cabinet dimensions (H x

W x D)

Converged Cabinet: 2000 mm x 600 mm x 1100 mm

Installation scenario

Single

-cabinet scenario

Installation space

The cabinet provides 42 U available space. The mounting bars are

adjustable forward or backward, and space is reserved at the rear of

the cabinet for installing PDU2000s horizontally and vertically.

Power distribution

6 kVA UPS

PDU2000: can be installed horizontally or vertically.

IEC and GB

models are optional for horizontal installation.

Lithium battery: 100 Ah/48 V DC

Operating temperature

Indoor:

0°C to +40°C

Operating humidity

–95% RH

IP rating

IP20

Installation mode

Installed on a concrete floor or an

ESD floor

Altitude

≤ 1000 m (

derated

when the altitude ranges from 1000 m to 4000 m)

1Overview

No. Component Onsite

Installation

(1) ECC800 Not

required

(2) Door status sensor Not

required

(3) Power distribution

subrack

Not

required

(4) UPS Not

required

(5) Lithium battery Required

(6) Water sensor Required

(7) Smoke detector Not

required

(8)

Temperature and

humidity (T/H)

sensor

Required

(9) PDU2000 Required

Cabinet Internal Layout (02116410)

The component layout is for reference only. The actual installation positions of the

components may vary.

If the IVS, server, and LAN switch are configured, determine their installation positions

based on the site requirements.

No. Component Onsite

Installation

(1) ECC800

Not required

(2)

Power

distribution

subrack

Not required

(3) UPS

Not required

(4)

Electronic clasp

lock

Not required

(5)

Lithium battery

Required

(6)

Integrated air

conditioner

Not required

(7) Water sensor Required

(8)

Smoke detector

Not required

(9) T/H sensor Required

(10) PDU2000 Required

No. Component Onsite

Installation

(1) ECC800

Not required

(2)

Power

distribution

subrack

Not required

(3) UPS

Not required

(4)

Electronic clasp

lock

Not required

(5)

Lithium battery

Required

(6) Transformer

Not required

(7) Integrated air

conditioner

Not required

(8) Water sensor Required

(9)

Smoke detector

Not required

(10) T/H sensor Required

(11) PDU2000 Required

Cabinet Internal Layout (02116412)

Cabinet Internal Layout (02116411)

(Front) (Rear)

Hardware Installation

1. Determine the cabinet position based on the

engineering layout diagram.

2. Place the cabinet at the correct installation position.

3. Level the cabinet using a wrench.

Use a measuring tape to check

that the vertical distance

between the top of the 2000

mm high cabinet and the floor

is 2000 mm (+3 mm). Then use

a level to check that the

cabinet is level.

Do not remove the anchor

bolts. Otherwise, you need to

rework them for use.

1. Remove the baffle plate from the smart cooling product.

2. Cut a cross in the middle of the rubber plug for the water pipe hole at the bottom of the

cabinet using an electrician's knife, and route the drainpipe.

3. Install the baffle plate for the smart cooling product.

1Installing the Cabinet

2Installing a Drainpipe for the Smart Cooling Product

For the 02116410 cabinet, install the

lithium battery at the 2 U or higher

position in the cabinet.

For the 02116411 cabinet, install the

lithium battery at the 11 U or higher

position in the cabinet.

For the 02116412 cabinet, install the

lithium battery at the 14 U or higher

position in the cabinet.

One lithium battery occupies 3 U space.

1. Push a lithium battery into the cabinet and

secure it.

3Installing Power Supply and Distribution Devices

3.1 Installing a Lithium Battery

3.2 Installing a PDU2000

Full-height Vertical PDU2000 Horizontal Non-intelligent PDU2000

Horizontal Intelligent PDU2000

For the 02116410 cabinet, one full-height vertical PDU2000 is installed in the left at the rear

of the cabinet.

For the 02116411 cabinet, two horizontal PDU2000s are installed. Intelligent PDU2000s and

non-intelligent PDU2000s are supported. Non-intelligent PDU2000s are installed at the 11 U

and 13 U positions at the rear of the cabinet. Intelligent PDU2000s are installed at the 10–

11 U and 12–13 U positions at the rear of the cabinet.

For the 02116412 cabinet, two horizontal non-intelligent PDU2000s are installed at the 16 U

and 18 U positions at the rear of the cabinet.

3.3 (Optional) Installing Busbars

If there is more than one

lithium battery, install

busbars.

For the 02116410 cabinet,

install the busbars at the 2

U and 3U positions in the

cabinet.

For the 02116411 cabinet,

install the busbars at the 17

U and 18 U positions in the

cabinet.

For the 02116412 cabinet,

install the busbars at the 20

U and 21 U positions in the

cabinet.

4Installing Monitoring Devices

4.1 Installing a SIM Card and Antenna

1. Remove the ECC800 main control module.

2. Install a SIM card. 3. Attach the antenna to the middle of

the cabinet top.

4. Connect the antenna cable.

4.2 Installing a PAD

1. (Optional) Remove the baffle plate from the front door of the Converged Cabinet.

2. (Optional) Install the PAD support fastener on the back of the front door of the Converged

Cabinet.

3. Adjust the PAD mounting support to match the dimensions of the PAD to be installed.

4. Remove the nuts from the PAD mounting support and install the support.

5. Route the PAD power cable through the cable hole in the PAD mounting support and

connect the cable to the PAD.

6. Adjust the feet on the top of the PAD mounting support and clamp the PAD to the PAD

mounting support.

7. Connect the ECC800 USB cable to the charging port on the PAD.

Adjusting screws

4.3 Installing T/H Sensors

The installation positions of the T/H sensors can be adjusted as required.

The default device address is 1.

Installing Remote T/H Sensors for the Smart Cooling Product

Installing T/H Sensors for the Cabinet

1. Place the water sensor on the floor under the cabinet.

2. Use an electrician's knife to cut a cross in the rubber plug for the cable hole at the bottom

of the cabinet.

3. Route the water sensor cable through the cable hole at the bottom of the cabinet, and

connect the cable to the water sensor cable connected to the ECC.

4.4 Installing an Electrode Water Sensor

1. Unpack the two T/H sensors, and attach one to the 33 U position on the right post of

the front door and the other to the 10 U position on the right post of the rear door of

the cabinet.

2. Set the DIP switch address of the T/H sensor on the front door to 2 and that of the

T/H sensor on the rear door to 1.

3. Insert the pre-routed cable into the port on the T/H sensor on the front door.

1. Unpack the two T/H sensors and attach them to the cabinet posts.

For the 02116410 cabinet, a T/H sensor is installed on the right post of the 39–41 U

position on the front door of the cabinet.

For the 02116411 or 02116412 cabinet, two T/H sensors are installed on the right post

of the 39 U position on the front door and 37 U position on the rear door of the cabinet.

2. Set the DIP switches on the T/H sensors.

For the 02116410 cabinet, set the DIP switch address of the T/H sensor on the front door

to 2.

For the 02116411 or 02116412 cabinet, set the DIP switch address of the T/H sensor on

the front door to 2 and that of the T/H sensor on the rear door to 1.

3. Insert the pre-routed cable into the port on the T/H sensor on the front door.

1. Determine the installation position of the server and check whether floating nuts are

installed. If not, install them first.

4.5 (Optional) Installing a Server

2. Install guide rails. 3. Place the server on the guide rails

and push it in to the cabinet.

4. Secure the server.

It is recommended that the server be installed at the 33–34 U position of the cabinet. You can

adjust the position based on site requirements.

c. Use a hook-and-loop fastener to

secure the power cable.

5. Connect the power cable of the server.

a. Wear an ESD wrist strap or ESD gloves.

b. Connect one end of the power cable to

the cable port on the AC power module of

the server.

d. Route the power cable along the cable tray neatly, use cable ties to bind the power

cable, and use diagonal pliers to trim off the excess of the cable ties.

1. (Optional) Install an SD card. 2. Secure the camera to the mounting plate.

(1) Cable outlet

4.6 (Optional) Installing a Camera

3. Secure the mounting plate to the top

of the cabinet front door.

4. Adjust the camera.

5. Install the transparent cover.

Altri manuali per FusionModule500

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Huawei Magazzinaggio

Huawei

Huawei OceanStor S2600 Manuale di installazione

Huawei

Huawei OceanStor 2600 V3 Video Surveillance Edition Specifiche tecniche

Huawei

Huawei OceanStor VIS6000 Series Manuale utente

Huawei

Huawei FusionModule1000A40 ICT Solution Manuale operativo

Huawei

Huawei FusionModule500 Manuale utente

Huawei

Huawei OceanStor 2600 V3 Video Surveillance Edition Manuale utente

Huawei

Huawei OceanStor VIS6300 Manuale utente

Huawei

Huawei E618 Manuale utente

Huawei

Huawei EG602 Manuale utente

Huawei

Huawei FusionModule5000 Manuale utente

Huawei

Huawei E180 Manuale utente

Huawei

Huawei FusionModule2000-S Manuale utente

Huawei

Huawei N2000H V3 Manuale utente

Huawei

Huawei FusionModule2000 V500R003C10 Manuale operativo

Huawei

Huawei 3 U Manuale utente

Huawei

Huawei ES3000 V5 Manuale utente

Huawei

Huawei OceanStor T Series Manuale utente

Huawei

Huawei OceanStor 5110F V5 Manuale utente

Huawei

Huawei OceanStor Dorado2100 G2 Manuale utente

Huawei

Huawei FusionModule5000 Manuale operativo

Huawei

Huawei FusionModule2000 V500R003C10 Manuale utente

Huawei

Huawei OceanStor V5 Series Manuale per l'uso e la cura

Huawei

Huawei ES3000 V5 Manuale utente

Huawei

Huawei FusionModule1000A40 ICT Solution Manuale utente

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

HP StorageWorks MSL2024 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

HP P9000 Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente