Hubbell VSLT-UP Manuale utente
A96462
VSLT-UP
8/13/2010
INSTALLATION INSTRUCTIONS CATALOG NUMBER
PART NO.APPRVDDATE
DATE REV.
16555 East Gale Avenue
City of Industry, CA 91745
(626)968-5666
24.86
4.16
8.31
11.16
8.16
1.28
2.07
4.14
(4)O.39"
THRU HOLES
O1.75
WIRE
WAY
1
1
(BY OTHERS)
INCOMING
WIRE LEADS
MOUNTING
HARDWARE
(BY OTHERS)
MOUNTING
SILICONE
ALL SURFACES
FIXTURE
ASSEMBLY
MOUNTING PLATE
JUNCTION BOX
EGRESS
LAMP SOCKET
EGRESS
EGRESS WIRING
TO 12 VOLT DC
(BEHIND PLATE)
WIRE CONNECTIONS
(BY OTHERS)
TURN OFF POWER.
RE-LAMPING:
2.
LAMP
MOUNTING PLATE
FRONT VIEW
SET SCREW
(4) P/N A84267
1/4-20 UNC X .63 LG
INSTALLATION COMPLETE.4.
3.
1. TURN OFF POWER.
BALLAST SERVICING:
2.
LAMP SOCKET
1.
TURN OFF POWER.
INSTALLATION
2.
SERVICE BALLAST.3.
4.
5.
6.
SURFACE
3.
4.
5.
1. TURN OFF POWER.
2.
6.
7.
3.
4.
EQUIPMENT GROUND.
5.
1. PULL INCOMING WIRE LEADS THROUGH WIREWAY
NOTE: TO BE MOUNTED INDEPENDENT OF JUNCTION
BOX. (MOUNTING HARDWARE BY OTHERS)
MAKE WIRE CONNECTIONS FROM INCOMING WIRE
LEADS TO FIXTURE ASSEMBLY. (WHITE TO WHITE,
BLACK TO BLACK, GREEN TO GREEN.)
NOTE: CONNECT GREEN GROUND LEAD TO
MEETS THE MOUNTING SURFACE.
THE EGRESS SOCKET MUST BE WIRED TO A
SEPARATE EMERGENCY CIRCUIT (12 VOLT D.C.)
MAKE WIRE CONNECTIONS.
RETURN FIXTURE HEAD ASSEMBLY TO TOP OF BODY
AND SECURE WITH (4) 1/4-20 x 5/8" SET SCREWS.
INSTALLATION COMPLETE
PLATE DISCONNECT WIRES. FIXTURE MUST BE
SUPPORTED DURING SERVICING.
REMOVE (3) 8-32 CAPTIVE SCREWS FROM TOP LID. PULL
UP ON LID TO ACCESS LAMP SOCKET, AND INSTALL LAMP.
RETURN LID AND SCREWS TO ORIGINAL POSITION
AND TIGHTEN SCREWS SECURELY.
LOOSEN (4) 1/4-20 x 5/8" SET SCREWS ON WALL CANOPY
LOOSEN (4) 1/4-20 x 5/8" SET SCREWS ON WALL
CANOPY AND LIFT FIXTURE ASSEMBLY AWAY
RE-LAMPING EGRESS LAMP
INSTALLATION COMPLETE.
REMOVE MR-11 LAMP FROM SOCKET AND REPLACE.
(4) 1/4-20 x 5/8" SET SCREWS.
INSTALLATION COMPLETE.
SECURE WITH (4) 1/4-20 x 5/8" SET SCREWS.
FROM MOUNTING PLATE.
AND LIFT FIXTURE ASSEMBLY AWAY FROM MOUNTING
(3) 8-32 CAPTIVE
SCREWS
AND SECURE MOUNTING PLATE TO MOUNTING SURFACE.
SECURE FIXTURE ASSEMBLY TO MOUNTING PLATE WITH
SILICONE ALL AROUND MOUNTING PLATE WHERE PLATE
RETURN FIXTURE ASSEMBLY TO MOUNTING PLATE AND
A96463
VSTL-DOWN
INSTALLATION INSTRUCTIONS CATALOG NUMBER
PART NO.APPRVDDATE
DATE REV.
16555 East Gale Avenue
City of Industry, CA 91745
(626)968-5666
11.16
8.16
1.28
2.07
4.14
4.16
8.31
24.86
O1.75"
WIRE
WAY
(4) O.39"
THRU HOLES
1
FIXTURE
SILICONE
(3) 8-32 CAPTIVE
SCREWS
LAMP
3.
1.
2.
1.
RE-LAMPING:
2.
4.
3.
4.
5.
6.
5.
1.
2.
6.
7.
3.
4.
5.
1.
2.
ALL SURFACES
EGRESS WIRING
TO 12 VOLT DC
(BEHIND PLATE)
JUNCTION BOX
(BY OTHERS)
WIRE CONNECTIONS
(BY OTHERS)
WIRE LEADS
LAMP SOCKET
WOUNTING PLATE
INCOMING
MOUNTING
SURFACE
MOUNTING
HARDWARE
(BY OTHERS)
3.
4.
1/4-20 UNC X .63 LG
INSTALLATION COMPLETE.
TURN OFF POWER.
BALLAST SERVICING:
TURN OFF POWER.
EGRESS
LAMP SOCKET
EGRESS
MOUNTING PLATE
FRONT VIEW
TURN OFF POWER.
RE-LAMPING EGRESS LAMP
EQUIPMENT GROUND.
TURN OFF POWER.
INSTALLATION
SERVICE BALLAST.
SET SCREW
(4) P/N A84267
ASSEMBLY
FROM MOUNTING PLATE.
SUPPORTED DURING SERVICING.
REMOVE (3) 8-32 CAPTIVE SCREWS FROM TOP LID. PULL
UP ON LID TO ACCESS LAMP SOCKET, AND INSTALL LAMP.
RETURN LID AND SCREWS TO ORIGINAL POSITION
AND TIGHTEN SCREWS SECURELY.
LOOSEN (4) 1/4-20 x 5/8" SET SCREWS ON WALL CANOPY
LOOSEN (4) 1/4-20 x 5/8" SET SCREWS ON WALL
CANOPY AND LIFT FIXTURE ASSEMBLY AWAY
INSTALLATION COMPLETE.
REMOVE MR-11 LAMP FROM SOCKET AND REPLACE.
SECURE FIXTURE ASSEMBLY TO MOUNTING PLATE WITH
(4) 1/4-20 x 5/8" SET SCREWS.
INSTALLATION COMPLETE.
RETURN FIXTURE ASSEMBLY TO MOUNTING PLATE AND
SECURE WITH (4) 1/4-20 x 5/8" SET SCREWS.
PULL INCOMING WIRE LEADS THROUGH WIREWAY
NOTE: TO BE MOUNTED INDEPENDENT OF JUNCTION
BOX. (MOUNTING HARDWARE BY OTHERS)
MAKE WIRE CONNECTIONS FROM INCOMING WIRE
LEADS TO FIXTURE ASSEMBLY. (WHITE TO WHITE,
BLACK TO BLACK, GREEN TO GREEN.)
NOTE: CONNECT GREEN GROUND LEAD TO
SILICONE ALL AROUND MOUNTING PLATE WHERE PLATE
MEETS THE MOUNTING SURFACE.
THE EGRESS SOCKET MUST BE WIRED TO A
SEPARATE EMERGENCY CIRCUIT (12 VOLT D.C.)
MAKE WIRE CONNECTIONS.
RETURN FIXTURE HEAD ASSEMBLY TO TOP OF BODY
AND SECURE WITH (4) 1/4-20 x 5/8" SET SCREWS.
INSTALLATION COMPLETE
PLATE DISCONNECT WIRES. FIXTURE MUST BE
AND LIFT FIXTURE ASSEMBLY AWAY FROM MOUNTING
AND SECURE MOUNTING PLATE TO MOUNTING SURFACE.
1
A96464
VSTS-DOWN
INSTALLATION INSTRUCTIONS CATALOG NUMBER
PART NO.APPRVDDATE
DATE REV.
16555 East Gale Avenue
City of Industry, CA 91745
(626)968-5666
(BY OTHERS)
FIXTURE
LAMP SOCKET
MOUNTING PLATE
MOUNTING
SURFACE
MOUNTING
HARDWARE
WIRE CONNECTIONS
(BY OTHERS)
INCOMING
WIRE LEADS
SILICONE
ALL SURFACES
EGRESS WIRING
TO 12 VOLT DC
(BEHIND PLATE)
JUNCTION BOX
(BY OTHERS)
(4) 8-32 CAPTIVE
SCREWS
SET SCREW
(4) P/N A84267
1/4-20 UNC X .63 LG
INSTALLATION COMPLETE.4.
3.
1. TURN OFF POWER.
BALLAST SERVICING:
2.
1. TURN OFF POWER.
RE-LAMPING:
2.
EGRESS
LAMP SOCKET
EGRESS
LAMP
FRONT VIEW
6.
4.
5.
1. TURN OFF POWER.
2.
7.
4.
EQUIPMENT GROUND.
5.
1. TURN OFF POWER.
INSTALLATION
2.
SERVICE BALLAST.3.
4.
5.
3.
ASSEMBLY
3. RETURN FIXTURE ASSEMBLY TO MOUNTING PLATE AND
SECURE WITH (4) 1/4-20 x 5/8" SET SCREWS.
FROM MOUNTING PLATE.
PULL INCOMING WIRE LEADS THROUGH WIREWAY
NOTE: TO BE MOUNTED INDEPENDENT OF JUNCTION
BOX. (MOUNTING HARDWARE BY OTHERS)
MAKE WIRE CONNECTIONS FROM INCOMING WIRE
LEADS TO FIXTURE ASSEMBLY. (WHITE TO WHITE,
BLACK TO BLACK, GREEN TO GREEN.)
NOTE: CONNECT GREEN GROUND LEAD TO
MEETS THE MOUNTING SURFACE.
THE EGRESS SOCKET MUST BE WIRED TO A
SEPARATE EMERGENCY CIRCUIT (12 VOLT D.C.)
MAKE WIRE CONNECTIONS.
RETURN FIXTURE HEAD ASSEMBLY TO TOP OF BODY
AND SECURE WITH (4) 1/4-20 x 5/8" SET SCREWS.
INSTALLATION COMPLETE
SUPPORTED DURING SERVICING.
REMOVE (4) 8-32 CAPTIVE SCREWS FROM TOP LID. PULL
UP ON LID TO ACCESS LAMP SOCKET, AND INSTALL LAMP.
RETURN LID AND SCREWS TO ORIGINAL POSITION
AND TIGHTEN SCREWS SECURELY.
LOOSEN (4) 1/4-20 x 5/8" SET SCREWS ON WALL CANOPY
AND LIFT FIXTURE ASSEMBLY AWAY FROM MOUNTING
MOUNTING PLATE
LOOSEN (4) 1/4-20 x 5/8" SET SCREWS ON WALL
CANOPY AND LIFT FIXTURE ASSEMBLY AWAY
RE-LAMPING EGRESS LAMP
INSTALLATION COMPLETE.
REMOVE MR-11 LAMP FROM SOCKET AND REPLACE.
(4) 1/4-20 x 5/8" SET SCREWS.
INSTALLATION COMPLETE.
6. PLATE DISCONNECT WIRES. FIXTURE MUST BE
AND SECURE MOUNTING PLATE TO MOUNTING SURFACE.
SECURE FIXTURE ASSEMBLY TO MOUNTING PLATE WITH
SILICONE ALL AROUND MOUNTING PLATE WHERE PLATE
3.44
5.75
5.75
2.37
4.75
13.37
(4) O.39"
THRU HOLES
O1.75"
WIRE
WAY
2.07
4.12
1
1
A96465
VSTS-UP
INSTALLATION INSTRUCTIONS CATALOG NUMBER
PART NO.APPRVDDATE
DATE REV.
16555 East Gale Avenue
City of Industry, CA 91745
(626)968-5666
MOUNTING PLATE
MOUNTING
SURFACE
MOUNTING
HARDWARE
(BY OTHERS)
SILICONE
EGRESS
ALL SURFACES
EGRESS WIRING
TO 12 VOLT DC
(BEHIND PLATE)
JUNCTION BOX
(BY OTHERS)
WIRE CONNECTIONS
(BY OTHERS)
INCOMING
WIRE LEADS
RE-LAMPING:
2.
LAMP SOCKET
LAMP SOCKET
EGRESS
LAMP
FRONT VIEW
SET SCREW
(4) P/N A84267
1/4-20 UNC X .63 LG
4.
3.
1. TURN OFF POWER.
BALLAST SERVICING:
2.
(4) 8-32 CAPTIVE
SCREWS
1. TURN OFF POWER.
1. TURN OFF POWER.
INSTALLATION
2.
SERVICE BALLAST.3.
4.
5.
6.
4.
5.
1. TURN OFF POWER.
2.
7.
4.
EQUIPMENT GROUND.
5.
FIXTURE
ASSEMBLY
3.
3.
BLACK TO BLACK, GREEN TO GREEN.)
NOTE: CONNECT GREEN GROUND LEAD TO
MEETS THE MOUNTING SURFACE.
THE EGRESS SOCKET MUST BE WIRED TO A
SEPARATE EMERGENCY CIRCUIT (12 VOLT D.C.)
MAKE WIRE CONNECTIONS.
RETURN FIXTURE HEAD ASSEMBLY TO TOP OF BODY
AND SECURE WITH (4) 1/4-20 x 5/8" SET SCREWS.
INSTALLATION COMPLETE
SUPPORTED DURING SERVICING.
REMOVE (4) 8-32 CAPTIVE SCREWS FROM BOTTOM LID.
PULL ON LID TO ACCESS LAMP SOCKET, INSTALL LAMP.
RETURN LID AND SCREWS TO ORIGINAL POSITION
AND TIGHTEN SCREWS SECURELY.
INSTALLATION COMPLETE.
LOOSEN (4) 1/4-20 x 5/8" SET SCREWS ON WALL CANOPY
AND LIFT FIXTURE ASSEMBLY AWAY FROM MOUNTING
MOUNTING PLATE
LOOSEN (4) 1/4-20 x 5/8" SET SCREWS ON WALL
CANOPY AND LIFT FIXTURE ASSEMBLY AWAY
RE-LAMPING EGRESS LAMP
INSTALLATION COMPLETE.
REMOVE MR-11 LAMP FROM SOCKET AND REPLACE.
(4) 1/4-20 x 5/8" SET SCREWS.
INSTALLATION COMPLETE.
SECURE WITH (4) 1/4-20 x 5/8" SET SCREWS.
FROM MOUNTING PLATE.
PULL INCOMING WIRE LEADS THROUGH WIREWAY
NOTE: TO BE MOUNTED INDEPENDENT OF JUNCTION
BOX. (MOUNTING HARDWARE BY OTHERS)
MAKE WIRE CONNECTIONS FROM INCOMING WIRE
LEADS TO FIXTURE ASSEMBLY. (WHITE TO WHITE,
6. PLATE DISCONNECT WIRES. FIXTURE MUST BE
AND SECURE MOUNTING PLATE TO MOUNTING SURFACE.
SECURE FIXTURE ASSEMBLY TO MOUNTING PLATE WITH
SILICONE ALL AROUND MOUNTING PLATE WHERE PLATE
RETURN FIXTURE ASSEMBLY TO MOUNTING PLATE AND
3.44
5.75
5.75
2.07
2.37
4.75
18.37
4.12
O1.75"
WIRE
WAY
(4) O.39
THRU HOLES
1
1
Indice
Altri manuali Hubbell Attrezzatura di illuminazione
Hubbell
Hubbell NXP2 Series Manuale utente
Hubbell
Hubbell SAVVANO Manuale utente
Hubbell
Hubbell DUAL LITE EVE Series Manuale utente
Hubbell
Hubbell Laredo LMC Manuale utente
Hubbell
Hubbell KIM LIGHTING VRB1 Manuale utente
Hubbell
Hubbell PRS Manuale utente
Hubbell
Hubbell Compass CU2SO Manuale utente
Hubbell
Hubbell Dual-Lite DYNC C1D2 Series Manuale utente
Hubbell
Hubbell homeSELECT RMS100 Manuale utente
Hubbell
Hubbell KILLARK VEB Series Manuale di istruzioni
Hubbell
Hubbell LITEFRAME LC4 Manuale utente
Hubbell
Hubbell DUAL LITE PG Series Manuale utente
Hubbell
Hubbell Litecontrol 22L Series Manuale utente
Hubbell
Hubbell Prescolite LBSLEDA Manuale utente
Hubbell
Hubbell Kim Lighting Lightvault LTV59 Manuale utente
Hubbell
Hubbell M-7679 R-PAC Manuale utente
Hubbell
Hubbell DUAL LITE N4X4 Manuale utente
Hubbell
Hubbell NutriLED Series Manuale utente
Hubbell
Hubbell Dual-Lite EV4D-02WAL Series Manuale
Hubbell
Hubbell Laredo LMC Manuale utente
