Hunter Hydrawise HPC Manuale utente

HPC - Using Hunter Remotes

The HPC face panel quickly and easily upgrades Pro-C® controllers (PC400 models

manufactured since March 2014) to next-generation smart controllers via the Hydrawise

platform. In addition, it lets contractors continue using their Roam and Roam XL remotes

for quick on-site management. HCC is also compatible with Hunter’s ROAM and ROAM XL

remotes, allowing for fast and reliable manual operation in the field from long-range

distances without the need for a smartphone. There is no need to remove the smart port

adapter from the controllers when doing a facepack upgrade.

Compatible models include all Hunter remotes: SRR, ICR, ROAM, and the ROAM-XL.

If the Smartport is not installed on the controller, see illustrations below for wiring

instructions.

Note: Any extension of the wiring on the SmartPort may result in an error message in

the controller display and possible malfunction of the remote unit due to radio interference.

In

some situations, lengthening of the harness may work fine, in others it may not work at all

(it is

site specific). In either case, extending the wiring harness should be done using shielded

cable to

minimize the possible effects of electrical noise. For easiest installation, order the Hunter

SmartPort shielded cable wiring harness. (P/N ROAM-SCWH) with a full 25' (7.6 meters)

of

shielded cable.

Wiring

1. Bottom 24 VAC terminal - Red wire

2. Second 24 VAC terminal - White wire

3. Remote terminal - Blue wire

Smart Port Wiring

Copyright 2020 Hunter Industries. All Rights Reserved. 1

Operation

The ROAM System will allow you to remotely turn on and off any station on your Hunter

controller with the press of a button. Once on, the station will run for the run time you have

designated in the remote. To remotely activate a station, follow the steps below:

1. Plug the receiver into a SmartPort® that is connected to a powered controller. The

receiver will beep 4 times followed by a 10-second pause and a single beep.

2. If your transmitter is not on (no display), wake it up by pressing and holding the MODE

button for 5 seconds. The Transmitter will display the active station.

3. Use the up and down buttons to display the station you would like to start.

4. Press the "Green Play Button" to start the station. The Transmitter will display the

Transmit icon . If you are near the receiver, you will hear it beep 2 times. This indicates

that the Receiver has received the command.

5. Press the "Red Stop Button" to turn off any station that is on. The display will show

the Transmit icon and receiver will beep again twice. The ROAM System is designed to

turn on

one station at a time (unless you activate a program). Therefore, turning a station on

while another station is operating will cause the operating station to turn off.

NOTE: The ROAM remote can activate any station on the controller whether the controller

dial is in the “SYSTEM OFF”, “RUN” or “RUN/BYPASS SENSOR” modes. If a sensor

device has been wired to the controller, the ROAM remote will NOT override the sensor for

Copyright 2020 Hunter Industries. All Rights Reserved. 2

manual operation. For more programming information, please see attached manuals for

both the ROAM and ROAM XL remotes.

Copyright 2020 Hunter Industries. All Rights Reserved. 3

Questo manuale è adatto per i seguenti modelli

6

Indice

Altri manuali Hunter Controllori

Hunter

Hunter ACC-1200 Manuale utente

Hunter

Hunter NODE-BT Manuale utente

Hunter

Hunter ICC2 Manuale utente

Hunter

Hunter SRC Plus Manuale utente

Hunter

Hunter PSC-Z Series Istruzioni operative

Hunter

Hunter XC Hybrid Istruzioni operative

Hunter

Hunter Pro-C Manuale utente

Hunter

Hunter IC600SS Manuale utente

Hunter

Hunter SVC-400 Manuale utente

Hunter

Hunter 600-Z Manuale utente

Hunter

Hunter NODE-BT Manuale utente

Hunter

Hunter X-CORE XC-2 Manuale utente

Hunter

Hunter 27178 Manuale utente

Hunter

Hunter Hydrawise HC-1200M Manuale utente

Hunter

Hunter Genesis Manuale utente

Hunter

Hunter ICC2 Manuale di installazione

Hunter

Hunter Smart Valve Controller Istruzioni operative

Hunter

Hunter Hydrawise Pro-HC Manuale utente

Hunter

Hunter Pro-C Manuale utente

Hunter

Hunter X-CORE Manuale utente

Hunter

Hunter X-CORE Istruzioni operative

Hunter

Hunter ICC2 Manuale utente

Hunter

Hunter EC Manuale utente

Hunter

Hunter i-core IC-600PL Istruzioni operative

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente