Hunter Bullet Spotlight Kit Manuale di istruzioni
Form# 43551-01
20090420
©2009 Hunter Fan Co.
English Español
Bullet Spotlight KitBullet Spotlight KitBullet Spotlight Kit
Owner’s Guide and Installation Manual
Manual De Propietario
2
43551-01 • 04/20/09 • Hunter Fan Company
Table Of Contents
Installing the Light Kit on Fans With
Removable Switch Housing ........4
Installing the Light Kit on Fans With
Non-Removable Switch Housing...6
Installing the Light Kit on the Hunter
Original .........................8
Troubleshooting.......................9
© 2009 Hunter Fan Company
Your new Hunter® light kit is an addition to your home or oce that
will provide comfort and performance for many years. is installation
and operation manual gives you complete instructions for installing
and operating your light kit.
We are proud of our work. We appreciate the opportunity to supply
you with the best products available anywhere in the world.
Before installing your light kit, for your records and warranty assistance,
record information from the carton and Hunter nameplate label.
Cautions and Warnings
•READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING
INSTALLATION. SAVE THESE INSTRUCTIONS.
• Use only Hunter replacement parts.
• To reduce the risk of personal injury, install this light xture only on
Hunter® fan types A through Z. Note: e fan type can be found on
the ceiling fan package or on the nameplate label located on top of
the motor housing of the ceiling fan.
• To avoid possible electrical shock, before installing light xtures,
disconnect the power by turning o the circuit breakers both to
the outlet box and to its associated wall switch location. If you
cannot lock the circuit breakers in the o position, securely fasten a
prominent warning device, such as a tag, to the service panel.
• Connect house wiring to the fan before attaching the light xture to
the fan.
• All wiring must be in accordance with national and local electrical
codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a
qualied electrician.
Welcome
3
43551-01 • 04/20/09 • Hunter Fan Company
Installation Methods of Hunter® Ceiling Fans Type A-Z
Removable Switch Housing
Non-removable Switch Housing
e Hunter Original
Your ® light kit can be installed in one of three
ways, depending on the type of switch housing. e steps
in this manual include instructions for all three installation
methods: Fans with removeable switch housings, fans
with non-removeable switch housings, and
Hunter Originals.
Preparing the Light Kit.
1. Disconnect power by turning o the circuit breakers
both to the outlet box and to its associated wall switch
location.
2. Loosen or remove the three screws on the top of the
light kit tter. Twist the tter clockwise and loosen it
from the light kit.
Screws
Light Kit
Fitter
4
43551-01 • 04/20/09 • Hunter Fan Company
1. Unscrew the three screws from the upper switch housing. Disconnect
the 9-pin plug connectors. Remove the lower switch housing.
2. Push the plug button from inside the lower switch housing to remove
the plug button and switch housing cap.
NOTE: Save the plug button and switch housing cap should you
choose to remove the light xture in the future.
3.
To attach the light kit tter, partially install two #6-32 screws
and the
lock washers on the red tag
into the switch housing.
4. Align the keyhole slots in the light kit tter with the #6-32 screws.
5. Turn the housing counterclockwise until the housing assembly screws
are rmly situated in the narrow end of the keyhole slots. Tighten
screws rmly.
6. Feed the two wires from the light xture through the center hole in
the lower switch housing.
7. To secure the light kit tter, thread the nut and washer onto the rod
from the light kit. Tighten the nut and washer you previously threaded
onto the rod from the light kit.
Removable Switch Housing
9-Pin Plug
Connector
Lower Switch
Housing
Plug Button
Screw
Steps 1-2
WARNING: Improper installation could cause the light xture to fall.
Light Kit
Fitter
Washer
Threaded
Rod
Switch
Housing
Nut
#6-32
Screw
Steps 3-5
Step 7
Installing the Light Kit on Fans With Removable Switch Housings
5
43551-01 • 04/20/09 • Hunter Fan Company
Installing the Light Kit on Fans With Removable Switch Housings (Continued)
8. Remove the wire connectors from the two wires in the switch housing
labeled “Connect Light Here” or “For Light Use.”
To connect the wires, hold the bare metal leads together and place a
wire connector over them, then twist the wire connector clockwise until
tight.
Connect the black wire with a white stripe from the switch housing to
the black wire from the light kit. Connect the white wire from the switch
housing to the white wire from the light kit. Secure all wire connections
using wire connectors.
CAUTION: Be sure no bare metal wires or wire strands are visible after
making the connections.
9. Finish attaching the light kit to the lower switch housing. Align the
notches in the sides of the light kit with the screws on the tter. Twist
the light kit counterclockwise to lock the screws in place. Tighten the
screws securely.
10. Reconnect the 9-pin plug connector.
11. Reinstall screws to reattach the lower switch housing to the upper
switch housing.
12. Install the included CFL bulbs.
13. e installation is complete and you can restore power to the ceiling fan
Wire
Connections
Step 8
Step 9
Plug
Connector
Lower Switch
Housing
Housing
Assembly Screw
Plug
Connector
Detail
Steps 10-11
CFL
(included)
Light Kit
Light Kit Fitter
6
43551-01 • 04/20/09 • Hunter Fan Company
1. Uninstall the two attachment screws from the switch housing cover.
2. Remove the plug or screw from the center of the switch housing cover.
NOTE: Save the plug button and switch housing cap should you choose to
remove the light xture in the future.
3. read the switch housing cover onto the light kit tter. Align the screw
holes in the light kit tter with the screw holes in the switch housing cover.
4. Install the nut and washer onto the threaded rod from the light kit tter to
secure the switch housing cover.
5. Remove the wire connectors from the two wires in the switch housing
labeled “Connect Light Here” or “For Light Use.” One wire is white and the
other wire is black with a white stripe.
6. Feed the two wires from the switch housing through the threaded rod in
the light kit tter.
7. Use the two attachment screws removed from the lower switch housing
and the lock washers on the red tag of the light kit tter. Install the screws
into the light kit and the housing. Securely tighten the two screws.
Switch
Housing
Cover
Plug
Attachment
Screw
Non-Removable Switch
Housing
Steps 1-2
WARNING: Improper installation could cause the light xture to
fall, or result in electrical shock or personal injury.
Nut
Washer
Screw
Hole
Switch
Housing
Cover
Light Kit Fitter
Steps 3-7
Attachment
Screw
Wire
Connectors Step 5
Installing the Light Kit on Fans With Non-Removable Switch Housing
7
43551-01 • 04/20/09 • Hunter Fan Company
Installing the Light Kit on Fans With Non-Removable Switch Housing Cont.
8. To connect the wires, hold the bare metal leads together and place a wire
connector over them, then twist the wire connector clockwise until tight.
Connect the black wire with a white stripe from the switch housing to
the black wire from the light kit. Connect the white wire from the switch
housing to the white wire from the light kit. Secure all wire connections
using wire connectors.
CAUTION: Be sure no bare metal wires or wire strands are visible after making
the connections.
9. Finish attaching the light kit to the lower switch housing. Align the
notches in the sides of the light kit with the screws on the tter. Finish
attaching the light kit to the lower switch housing. Align the notches
in the sides of the light kit with the screws on the tter. Twist the tter
counterclockwise to lock the screws in place. Tighten the screws securely.
10. Install the included CFL bulbs.
11. e installation is complete and you can restore power to the ceiling fan.
Wires
and Wire
connectors
Step 8
Step 9
CFL
(included)
Light Kit
Light Kit Fitter
8
43551-01 • 04/20/09 • Hunter Fan Company
Switch
Housing
Plate
Screw
Attachment
Screws
Light Kit
Fitter
Step 1
Steps 2-4
Wire
Connectors
Step 5
Step 6
1. Uninstall the two attachment screws from the switch housing cover.
NOTE: Save the switch housing cover should you choose to remove the
light xture in the future.
2. Remove the wire connectors from the two wires in the switch housing
labeled “Connect Light Here” or “For Light Use.” One wire is white and the
other wire is black with a white stripe.
3. Feed the two wires from the switch housing through the threaded rod in
the light kit tter.
4. Use the two attachment screws removed from the lower switch housing
and the lock washers on the red tag of the light kit tter. Partially install the
screws in the switch housing. Install the screws into the light kit and the
housing.Rotate the housing counterclockwise until the screws are locked
into the narrow ends of the keyhole slots. Securely tighten the two screws.
5. To connect the wires, hold the bare metal leads together and place a wire
connector over them, then twist the wire connector clockwise until tight.
Connect the black wire with a white stripe from the switch housing to
the black wire from the light kit. Connect the white wire from the switch
housing to the white wire from the light kit. Secure all wire connections
using wire connectors.
CAUTION: Be sure no bare metal wires or wire strands are visible after making
the connections.
6. Finish attaching the light kit to the lower switch housing. Align the notches
in the sides of the light kit with the screws on the tter. Twist the tter
counterclockwise to lock the screws in place. Tighten the screws securely.
7. Install the included CFL bulbs.
8. e installation is complete and you can restore power to the ceiling fan.
CFL
(included)
Light Kit
Light Kit Fitter
Installing the Light Kit on the Hunter Original
9
43551-01 • 04/20/09 • Hunter Fan Company
Troubleshooting
Light does not come on.
1. Make sure bulbs are installed properly.
2. Make sure breakers or fuses are on.
3. Verify that the light power lead is connected at the ceiling. Refer to
your ceiling fan manual for locating assembly and wiring.
If you need parts or service assistance, please call
888-830-1326 or visit us at our Web site at
http://www.hunterfan.com.
Hunter Fan Company
7130 Goodlett Farms Pkwy. # 400
Memphis, Tennessee 38016
is Light Fixture Weighs 4 lbs. Printed in China
Troubleshooting
Indice
Altri manuali Hunter Illuminazione domestica
Hunter
Hunter MM288PU Manuale del proprietario
Hunter
Hunter Tea Stain Bowl Light Kit Manuale utente
Hunter
Hunter Casbah Light Kit Manuale utente
Hunter
Hunter Floating Glass Light Kit Manuale utente
Hunter
Hunter Tribeca Light Kit Tribeca Light Kit Manuale di istruzioni
Hunter
Hunter Marine II Manuale di istruzioni
Hunter
Hunter 10” Manuale utente
Hunter
Hunter Dual Function Bowl Light Kit Manuale di istruzioni
