PURE LED
Aug 2023 V2 Hunza-High-Power-Spike-Spot_SS-HP_Installation-Instructions-International HUNZATM
©Copyright 2023. This document contains proprietary information of Hunza™. Its receipt or possession does not convey any rights to reproduce or disclose its content.
2
2. All Hunza™ luminaires must be installed according to the installation
instructions supplied with the luminaires by a certificated electrician. The
installer is solely responsible for determining the correct wiring of series or
parallel luminaires.
3. All connections within the electrical system must be waterproof.
4. The environment in which the fixture is to be installed must be considered
carefully when selecting the finish. Solid Bronze, Copper or Stainless Steel
luminaires are recommended for high-risk environments such as near salt water
or salt laden air. Aluminium luminaires may not be covered by the full warranty
in these situations.
5. Bronze, Copper and Aluminium fixtures are not recommended for installation
in areas high in geothermal activity. Warranty is not offered for these materials in
geothermal areas.
6. For aluminium fixtures, warranty on the powder coat finish is excluded for
failure due to exposure to: chemical substances in the ground, fertilizers and
water containing corrosive agents.
7. Stainless Steel requires regular cleaning with fresh water when installed in
high salinity environments. (Refer to instructions supplied with luminaire). The
warranty does not cover tea staining or surface pitting caused by inadequate
maintenance procedures.
8. Hunza™ underwater fixtures are not covered by warranty in situations where
there are chemical imbalances in the water.
9. Warranty is excluded for corrosion due to electrolytic reactions caused by the
presence of electrical current in the ground or water.
10. Warranty excludes impact damage (except for glass lenses), incorrect
installation and incorrect re-assembly.
11. Fixtures must be kept properly maintained, including replacement of gaskets
and lenses when necessary and use of approved wattage lamps.
12. Fixtures must not be pressure washed (water blasted). Please refer to IP
ratings of each fixture.
13. Hunza™, at its discretion, may replace components to remedy the fault or
supply a replacement fixture.
14. Hunza™ warranty is limited to the repair or replacement of products ONLY.
Labour charges will not be accepted.
15. Warranty on transformers is limited to 5 years, and applies only when
transformers are installed in environments at less than 40 degrees Celsius
ambient temperature.
16. Hunza™ will not be liable for any labour charges for any repair or
replacement of defective drivers. Drivers have their own manufacturer warranty
and any faults will be at the responsibility of the manufacturer.
17. Hunza™ reserves the right to limit liability on non-standard (custom
designed) luminaires and/or delivery arrangements.
18. Damage caused by lightning strikes, high voltage spikes or incorrect polarity
connection is not covered by the Black Label warranty.
19. Polycarbonate and acrylic lenses are limited to a 5 year warranty.
20. N.B. Acrylic Quartz, Cloak, TIR or Bollard lenses must NOT be cleaned with
any petrochemical substance. This will void the warranty.
21. Warranty excludes halogen lamps and lamp holders, which are consumable
items.
22. Use of 3rd party colour correction gels and filters will void the warranty if
used with PureLED products.
HUNZA™ BLACK LABEL WARRANTY
When you purchase or specify a Hunza™ luminaire, you get the benefit of
the legendary Hunza™ reputation for high quality and long life. We back this
up with our Black Label extended warranty, offering up to 25 years on body
components and 5 years on the integral PURE LED™ system. When installed
and maintained properly, Hunza™ luminaires will last a lifetime so we keep
serviceability firmly in mind when designing the components and system
construction.
Hunza™ 25 Year Warranty All Hunza™ Cast Bronze luminaires have a 25
year replacement warranty against body corrosion, subject to the standard
conditions listed below.
Hunza™ 10 Year Warranty Hunza™ stainless steel* and copper luminaires have
a 10 year replacement warranty on body components, subject to the standard
conditions listed below (*excludes underwater fixtures ).
Hunza™ 5 Year Warranty All Hunza™ aluminium luminaires with a UV stable
powder-coat finish and underwater fixtures have a 5 year replacement warranty
on body components, subject to the standard conditions listed below.
Hunza™ Lifetime Warranty All glass lenses supplied with Hunza™ luminaires
have a lifetime warranty.
Hunza™ PURE LED™ System Integral PURE LED components have a 5 year
warranty and are subject to the standard conditions listed below.
Other Hunza™ Components 5 year warranty on other Hunza™ components,
Hunza™ accessories and are subject to the standard conditions listed below.
Third Party Components Coverage on plug-in (drop-in) LED lamps, power
supplies and other 3rd-party components are limited to the manufacturer’s
warranty.
STANDARD CONDITIONS:
1. Warranty is subject to proof of purchase being provided and begins at the
date of invoicing from the factory.
DO NOT USE BLEACH, concentrated cleaners, or solvents under any circumstances. DO NOT water blast/pressure blast
fixtures. DO NOT USE ABRASIVE COMPOUNDS.
POWDER-COATED ALUMINIUM: To keep your powdercoated aluminium fixtures in the best condition, please clean
by wiping gently with a damp, soft cloth or chamois and window cleaner. Do not use metal polishing compounds like
Brasso1, Autosol2 etc. To restore the lustre of the paint finish, use a silicon spray.
Powdercoated aluminium fixtures are not recommended for installation near the sea or close to salt water.
CAST BRONZE, COPPER AND BRASS will age naturally and will patina over time, it is not necessary to clean copper
frequently. When they do require cleaning, wipe them with a damp cloth. DO NOT use polishing compounds.
HUNZA PRODUCTIONS LTD
130 Felton Mathew Ave
Saint Johns, Auckland 1072
New Zealand
Ph: +64-9-528 9471
Fax: +64-9-528 9471
Hunza™ fixtures are available from specialist outdoor lighting distributors.
Specifications, Installation, IES, CAD & Guides are available online: www.hunzalighting.com
FOR 316 MARINE GRADE STAINLESS STEEL LUMINARIES: To maintain the finish of 316 stainless steel it is
recommended to wash the luminaire with fresh water from time to time to stop salt and corrosive elements building
up. For extra protection, we recommend applying a thin film of CLEAR SILICON GREASE (Moreys© Crystal Clear Food
Machinery MP2 Grease) to the exterior of fixture between maintenance.
ELECTRO POLISHES still require regular maintenance. Even an electro polished stainless steel fixture under an eave or
roof will suffer from the build up of salt deposits as it will not be washed away by rain.
MATERIAL MAINTENANCE
Made in New Zealand
by Hunza™ Productions LTD
SS/HP
PURE LED REPLACEMENT
CAUTION: Make sure that the power to the luminaire is switched off before attempting to change the lamp. Beware of hot luminaire and lamp. Make absolutely sure when changing lamps that the correct wattage
lamp is installed. Incorrect wattage lamps may cause HUNZA™ transformers to overload causing them to heat up and turn the luminaires off.
LED REPLACEMENT (PLEASE PAY CLOSE ATTENTION TO THE COMPONENT ORDER): Unscrew the lens ring from the front of the fixture. Carefully remove the lens, gasket and heat sink assembly, noting which
order they are installed. Unclip the “C” spring holder from the front of the heat sink and remove the plastic optic. Unscrew the two hex head screws holding the round LED board in place and remove the board.
Put the new LED board in place and reinsert the screws, using a small amount of white heat sink compound underneath the board. Replace the plastic optic and hold in place with the “C” clip. Insert the front
lens with the step facing outwards, put the gasket around the stop and hold in place while screwing the lens ring back in place, ensuring that the gasket is not bunched up.
INTERNATIONAL
Wiring Guide
Make water proof connections using heavy walled adhesive lined heat shrink (refer to wiring guide below). Recommendations: Run all low voltage cables in flexible
conduit for extra protection. Use Hunza Cable Joint Kit CJK15.0 Heavy Duty Cable Boots are available for additional ingress protection.
INPUT:
240VAC
Mains Voltage
Circuit: Wire in Series With Remote Driver
Please see installation instructions
for full details.
FIXTURE INPUT:
Constant Current DC
REQUIRED
NOT SUPPLIED
POWER SUPPLY:
Constant Current
LED Driver
Circuit: 24VDC - Wired In Parallel
Please see installation instructions
for full details.
FIXTURE INPUT:
24VDC Constant Voltage
REQUIRED
NOT SUPPLIED
POWER SUPPLY:
Constant Voltage
LED Driver
D
R
I
V
E
R
2
4
V
D
C
D
R
I
V
E
R
2
4
V
D
C
INPUT:
240VAC
Mains Voltage
LUMINAIRE MUST
BE GROUNDED
Circuit: 240VAC - Wired in Parallel
Please see installation instructions
for full details.
FIXTURE INPUT: 240VAC Mains Voltage
D
R
I
V
E
R
1
1
0
/
2
4
0
V
A
C
D
R
I
V
E
R
1
1
0
/
2
4
0
V
A
C
D
R
I
V
E
R
1
1
0
/
2
4
0
V
A
C
